This reverts commit d1857056.

Double commit, noticed by Thomas Gleixner.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Revert double commit by mistake. Noticed by Thomas Gleixner.

This reverts commit cc7e5166.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

This reverts commit 01a5bba5.

There seem to be some FADTs around with bogus information
in the v2 fields. Revert this patch for now until
this can be properly resolved.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Subject:ACPI: Set FAN device to correct state in boot phase
From: Zhao Yakui <yakui.zhao@intel.com>

On some laptops when ACPI FAN driver is loaded, maybe the FAN device will be
turned on. But if the temperature is below the threshold, the corresponding
FAN device should be turned off in the course of loading thermal driver.

So it is necessary to set the FAN device to the correct state in course of loading
the thermal driver.

http://bugzilla.kernel.org/show_bug.cgi?id=8049Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

According to acpi spec , the objectes of  _BCL and _BCM are required if
integrated LCD is present and supports brightness level and the _BQC is
the optional object. So the _BQC object will be ignored when the backlight
device is registered.
At the same time when there is no _BQC object, the current brightness will be
set to the maximum.

http://bugzilla.kernel.org/show_bug.cgi?id=10206Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NZhang Rui  <rui.zhang@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Silently ignore _PRS End Tags.  We already ignore Start Dependent Functions in
_PRS, and we already ignore End Tags in _CRS, so we might as well ignore End
Tags in _PRS as well.

Silently ignore _PRS IRQ descriptors that mention no interrupts.  The spec
allows this (section 6.4.2.1 in ACPI 3.0b spec), and it probably means the
interrupt link can't be configured at all.

This patch doesn't change any functional behavior; it just removes confusing
complaints like these:

    ACPI: Blank IRQ resource
    ACPI: Resource is not an IRQ entry

when parsing _PRS data "23 00 00 18 79 00" from an IBM xSeries 335 dual
Pentium IV Xeon 2.40 GHz machine.  For more details, see
    http://bugzilla.kernel.org/show_bug.cgi?id=11049

The "23 00 00 18" part is a three-byte-long small IRQ resource with no bits set
in the IRQ mask ("00 00"), and level-triggered, active low, shareable ("18").

The "79 00" is an End Tag (type 0x7).  It is superfluous since there is no
Start Dependent Function tag and there are no resources after it, but it is
harmless.

Thanks to Gabriele Trombetti <g.trombetti.lkrnl1213@logicschema.com>
(aka Kurk) for reporting this and testing the patch.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

The (1.0 inherited) separate length fields in the FADT are byte granular.
Further, PM1a/b may have distinct lengths and live in distinct address spaces.
 acpi_tb_convert_fadt() should account for all of these conditions.

Apart from these changes I'm puzzled by the fact that, not just for
acpi_gbl_xpm1{a,b}_enable, acpi_hw_low_level_{read,write}() get an explicit
size passed rather than using the size found in the passed GAS.  What happens
on a platform that defines PM1{a,b} wider than 16 bits?  Of course,
acpi_hw_low_level_{read,write}() at present are entirely un-prepared to deal
with sizes other than 8, 16, or 32, not to speak of a non-zero bit_offset or
access_width...
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

Signed-off-by: NAaron Durbin <adurbin@google.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

Convert printks to use dev_printk().  The most obvious change will
be messages like this:

   -ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 31 (level, low) -> IRQ 31
   +cciss 0000:00:04.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Fix use of uninitialized device->brightness.
Signed-off-by: NJulia Jomantaite <julia.jomantaite@gmail.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Acked-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

If a system matches in this DMI table,
Linux will disable MWAIT support for idle.
ie. "idle=nomwait" is automatically invoked
and C1_FFH and C2C3_FFH access mode are disabled.

http://bugzilla.kernel.org/show_bug.cgi?id=10807
http://bugzilla.kernel.org/show_bug.cgi?id=10914Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLi Shaohua <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

"idle=nomwait" disables the use of the MWAIT
instruction from both C1 (C1_FFH) and deeper (C2C3_FFH)
C-states.

When MWAIT is unavailable, the BIOS and OS generally
negotiate to use the HALT instruction for C1,
and use IO accesses for deeper C-states.

This option is useful for power and performance
comparisons, and also to work around BIOS bugs
where broken MWAIT support is advertised.

http://bugzilla.kernel.org/show_bug.cgi?id=10807
http://bugzilla.kernel.org/show_bug.cgi?id=10914Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLi Shaohua <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

"idle=halt" limits the idle loop to using
the halt instruction.  No MWAIT, no IO accesses,
no C-states deeper than C1.

If something is broken in the idle code,
"idle=halt" is a less severe workaround
than "idle=poll" which disables all power savings.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Allow users to enable/disable/clear a specific & valid GPE/Fixed Event
in user space.

This is useful for debugging, especially for some
interrupt storm issues.

All wakeup GPEs are disabled and they can not be enabled at runtime,
and we mark them as invalid.

All GPEs that don't have a _Lxx/_Exx method are marked as invalid.

All Fixed Events that don't have an event handler are marked as invalid
and they can't be enabled until an event handler is registered.
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLing Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Loop was terminating one iteration early, missing one of the
debugger handshake mutexes. Linn Crosetto.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Removed extraneous else clauses, other general cleanup.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Eliminated unnecessary operands; eliminated use of negative index
in loop.  Operands now displayed in correct order, not backwards.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

This problem was introduced in 20080514 as a result of the
elimination of the acpi_native_uint type. Code uses a negative
array index, which should be eliminated.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Synchronized tables with current specifications.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Some BIOSs erroneously reverse the _PRT SourceName and the
SourceIndex.  Detect and repair this problem. MS ACPI also allows
and repairs this problem, thus ACPICA must also.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Mostly MODULE_NAME and printf format strings.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Remove pointer cast warnings and fix for a debug printf.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

From lint.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

No longer needed; replaced mostly with u32, but also acpi_size
where a type that changes 32/64 bit on 32/64-bit platforms is
required.

v2: Fix a cast of a 32-bit int to a pointer in ACPI to avoid a compiler warning.
from David Howells
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Added NULL fields to the exception string arrays to eliminate
the -1 subtraction on the SubStatus field.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Fixes problem where the new method argument count validation mechanism
will enter an infinite loop when a GPE method is dispatched.
Problem fixed be removing the obsolete code that passes GPE block
information to the notify handler via the control method parameter pointer.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Error if too few arguments, warning if too many. This applies
only to external programmatic control method execution, not
method-to-method calls within the AML.
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Remove the obsolete workaround for a Toshiba Satellite 4030cdt
S1 problem from drivers/acpi/sleep/main.c .
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NLen Brown <len.brown@intel.com>

Get rid of a superfluous acpi_pm_device_sleep_state() parameter.  The
only legitimate value of that parameter must be derived from the first
parameter, which is what all the callers already do.  (However, this
does not address the fact that ACPI still doesn't set up those flags.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Ingo Molnar wrote:
> -tip auto-testing started triggering this spinlock corruption message
> yesterday:
>
> [    3.976213] calling  acpi_rtc_init+0x0/0xd3
> [    3.980213] ACPI Exception (utmutex-0263): AE_BAD_PARAMETER, Thread F7C50000 could not acquire Mutex [3] [20080321]
> [    3.992213] BUG: spinlock bad magic on CPU#0, swapper/1
> [    3.992213]  lock: c2508dc4, .magic: 00000000, .owner: swapper/1, .owner_cpu: 0

This is apparently because some parts of ACPI, including mutexes, are not
initialized when acpi=off is passed to the kernel.
Reported-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NVegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Implemented another change for the GPE disable. We now perform a
read-change-write of the enable register instead of simply writing out the
cached enable mask. This will prevent inadvertent enabling of GPEs if a rogue
GPE is received during initialization (before GPE handlers are installed.)

http://bugzilla.kernel.org/show_bug.cgi?id=6217Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Fix printk format warning:

linux-next-20080617/drivers/acpi/processor_throttling.c:1258: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

http://bugzilla.kernel.org/show_bug.cgi?id=9704

When echo some invalid values to /proc/acpi/processor/*/throttling,
there isn't any error info returned, on the contray, it sets
throttling value to some T* successfully, obviously, this is incorrect,
a correct way should be to let it fail and return error info.

This patch fixed the aforementioned issue, it also enables
/proc/acpi/processor/*/throttling to accept such values as 't0' and 'T0',
it also strictly limits /proc/acpi/processor/*/throttling only to accept
 "*", "t*" and "T*", "*" is the throttling state value the processor can
support, current, it is 0 - 7.

Before applying this patch, the test result is below:

[root@localhost acpi]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T1
state available: T0 to T7
states:
    T0:                  100%
   *T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost acpi]# echo "1xxxxxx" > /proc/acpi/processor/CPU0/throttling
[root@localhost acpi]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T1
state available: T0 to T7
states:
    T0:                  100%
   *T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost acpi]# echo "0" > /proc/acpi/processor/CPU0/throttling
[root@localhost acpi]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost acpi]# cd /
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost /]# echo "T0" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost /]# echo "T7" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost /]# echo "T100" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost /]# echo "xxx" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost /]# echo "2xxxx" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T2
state available: T0 to T7
states:
    T0:                  100%
    T1:                  87%
   *T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost /]# echo "" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost /]# echo "7777" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost /]# echo "7xxx" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T7
state available: T0 to T7
states:
    T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
   *T7:                  12%
[root@localhost /]#

After applying this patch, the test result is below:

[root@localhost linux-2.6.24-rc6]# echo > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo "" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo "0" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# echo "t0" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# echo "T0" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost linux-2.6.24-rc6]# echo "T7" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T7
state available: T0 to T7
states:
    T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
   *T7:                  12%
[root@localhost linux-2.6.24-rc6]# echo "T8" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# vi drivers/acpi/processor_throttling.c
[root@localhost linux-2.6.24-rc6]# echo "T8" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo "t7" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# echo "t70" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo "70" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo "7000" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo "70" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo "xxx" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo -n > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# echo -n "" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# echo $?
0
[root@localhost linux-2.6.24-rc6]# echo -n "" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T7
state available: T0 to T7
states:
    T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
   *T7:                  12%
[root@localhost linux-2.6.24-rc6]# echo -n "" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T7
state available: T0 to T7
states:
    T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
   *T7:                  12%
[root@localhost linux-2.6.24-rc6]# echo t0 > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# echo T0 > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# echo Tt0 > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo T > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]#
Signed-off-by: NYi Yang <yi.y.yang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Under /proc/acpi, there is a fan control interface, a user can
set 0 or 3 to /proc/acpi/fan/*/state, 0 denotes D0 state, 3
denotes D3 state, but in current implementation, a user can
set a fan to D1 state by any char excluding '1', '2' and '3'.

For example:

[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost acpi]# echo "" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  on
[root@localhost acpi]# echo "3" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost acpi]# echo "xxxxx" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  on

Obviously, such inputs as "" and "xxxxx" are invalid for fan state.

This patch fixes this issue, it strictly limits fan state only to
accept 0, 1, 2 and 3, any other inputs are invalid.

Before applying this patch, the test result is:

[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost acpi]# echo "" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  on
[root@localhost acpi]# echo "3" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost acpi]# echo "xxxxx" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  on
[root@localhost acpi]# echo "3" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost acpi]# echo "3x" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost acpi]# echo "-1x" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  on
[root@localhost acpi]#

After applying this patch, the test result is:

[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost ~]# echo "" > /proc/acpi/fan/C31B/state
-bash: echo: write error: Invalid argument
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost ~]# echo "3" > /proc/acpi/fan/C31B/state
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost ~]# echo "xxxxx" > /proc/acpi/fan/C31B/state
-bash: echo: write error: Invalid argument
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost ~]# echo "-1x" > /proc/acpi/fan/C31B/state
-bash: echo: write error: Invalid argument
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost ~]# echo "0" > //proc/acpi/fan/C31B/state
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  on
[root@localhost ~]# echo "4" > //proc/acpi/fan/C31B/state
-bash: echo: write error: Invalid argument
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  on
[root@localhost ~]# echo "3" > //proc/acpi/fan/C31B/state
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost ~]# echo "0" > //proc/acpi/fan/C31B/state
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  on
[root@localhost ~]# echo "3x" > //proc/acpi/fan/C31B/state
-bash: echo: write error: Invalid argument
[root@localhost ~]#
Signed-off-by: NYi Yang <yi.y.yang@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Acked-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

http://bugzilla.kernel.org/show_bug.cgi?id=9772Signed-off-by: NAlok N Kataria <akataria@vmware.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Change processors from an array sized by NR_CPUS to a per_cpu variable.
Signed-off-by: NMike Travis <travis@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Sys I/F under acpi device node and sysdev device node are both
needed for cpu hot-removal. User space need this link so that
they know they are poking the sys I/F for the same cpu.
http://bugzilla.kernel.org/show_bug.cgi?id=9772Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

The ACPI device node for the cpu has already been unregistered
when acpi_processor_handle_eject is called.
Thus we should offline the cpu and continue, rather than a failure here.
http://bugzilla.kernel.org/show_bug.cgi?id=9772Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

"/sys/devices/LNXSYSTM:00/.../eject" is used to evaluate _EJx method
and eject a device in user space.
But system hangs when poking the "eject" file because that
the device hot-removal code invoke the driver .remove method which will
try to remove the "eject" file as a result.

Queues the hot-removal function for deferred execution in this patch.
http://bugzilla.kernel.org/show_bug.cgi?id=9772Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>