This patch adds wol support for the older 440x nics that use pattern matching.
This patch is a redo thanks to feedback from Michael Chan and Francois Romieu.
Signed-off-by: NGary Zambrano  <zambrano@broadcom.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds a parameter to init_hw() to not completely initialize
the nic for wol.
Signed-off-by: NGary Zambrano <zambrano@broadcom.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Adds wol to the driver.
This is a redo of a previous patch thanks to feedback from Francois Romieu.

Signed-off-by Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fixes for speed/duplex/autoneg settings and driver settings info.
This is a redo of a previous patch thanks to feedback from Jeff Garzik.
Signed-off-by: NGary Zambrano <zambrano@broadcom.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Adds power-management (suspend/resume) support to the AT91RM9200
Ethernet driver.
Patch from David Brownell.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Moved global ether_clk variable into controller data structure.
Patch from David Brownell.

Davicom 9161 PHY was being incorrectly displayed as "9196".
Patch from Brian Stafford.

clk_get() doesn't return NULL on error, so the return value needs to be
tested with IS_ERR().

Whitespace cleanup.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Adds support for the MII ioctls via generic_mii_ioctl().
Patch from Brian Stafford.

Set the mii.phy_id to the detected PHY address, otherwise ethtool cannot
access PHYs other than 0.
Patch from Roman Kolesnikov.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

For Ethernet PHYs that don't have an IRQ pin or boards that don't
connect the IRQ pin to the processor, we enable a timer to poll the
PHY's link state.

Patch originally supplied by Eric Benard and Roman Kolesnikov.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

IOC3's homegrown DMA mapping functions that are used to optimize things
a little on IP27 set the wrong bit.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The AGP default doesn't work well with other selects, so use a select for
GART_IOMMU as well.  Remove a redundant default for SWIOTLB as well.
Signed-off-by: NRoman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

VGA_MAP_MEM translates to ioremap() on some architectures.  It makes sense
to do this to vga_vram_base, because we're going to access memory between
vga_vram_base and vga_vram_end.

But it doesn't really make sense to map starting at vga_vram_end, because
we aren't going to access memory starting there.  On ia64, which always has
to be different, ioremapping vga_vram_end gives you something completely
incompatible with ioremapped vga_vram_start, so vga_vram_size ends up being
nonsense.

As a bonus, we often know the size up front, so we can use ioremap()
correctly, rather than giving it a zero size.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Someone changed skb_linearize().

Cc: Brice Goglin <bgoglin@myri.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

drivers/w1/w1.c:423: warning: long long unsigned int format, __u64 arg (arg 8)

u64 is not, never has been and never will be "unsigned long long"!

While we're there, fix up some code layout - it looks awful in an 80-col
display.

Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If w1 is not enabled, w1_con should not appear in configuration,
even if no logic is turned on without w1.
W1_CON should depend on W1 also.
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

From: Adrian Bunk <bunk@stusta.de>

drivers/w1/w1.c:197: error: static declaration of 'w1_bus_type' follows non-static declaration
drivers/w1/w1.h:217: error: previous declaration of 'w1_bus_type' was here
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

From: Jean-Luc Leger <jean-luc.leger@dspnet.fr.eu.org>

Default values for boolean and tristate options can only be 'y', 'm' or 'n'.
This patch fixes dependencies of W1_SLAVE_DS2433_CRC.
Signed-off-by: NJean-Luc Leger <jean-luc.leger@dspnet.fr.eu.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch contains the following possible cleanups:
- the following file did't #include the header with the prototypes for
  it's global functions:
  - w1_int.c
- #if 0 the following unused global function:
  - w1_family.c: w1_family_get()
- make the following needlessly global functions static:
  - w1_family.c: __w1_family_put()
  - w1_io.c: w1_delay()
  - w1_io.c: w1_touch_bit()
  - w1_io.c: w1_read_8()
- remove the following unused EXPORT_SYMBOL's:
  - w1_family.c: w1_family_put
  - w1_family.c: w1_family_registered
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Nice cleanup spotted by Adrian Bunk, which was lost due to moving to the
completely new functionality.

Shame-shame-shame on me.
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

From: Andrew Morton <akpm@osdl.org>

WARNING: "w1_read_block" [drivers/w1/slaves/w1_therm.ko] undefined!
WARNING: "w1_write_8" [drivers/w1/slaves/w1_therm.ko] undefined!
WARNING: "w1_reset_select_slave" [drivers/w1/slaves/w1_therm.ko] undefined!
WARNING: "w1_reset_bus" [drivers/w1/slaves/w1_ds2433.ko] undefined!
WARNING: "w1_write_8" [drivers/w1/slaves/w1_ds2433.ko] undefined!
WARNING: "w1_read_block" [drivers/w1/slaves/w1_ds2433.ko] undefined!
WARNING: "w1_write_block" [drivers/w1/slaves/w1_ds2433.ko] undefined!
WARNING: "w1_reset_select_slave" [drivers/w1/slaves/w1_ds2433.ko] undefined!

Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use mutexes instead of semaphores.
Patch tested on x86_64 and i386 with test bus master driver.
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make w1 connector notifications depend on connector.
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There are three types of messages between w1 core and userspace:
1. Events. They are generated each time new master or slave device found
	either due to automatic or requested search.
2. Userspace commands. Includes read/write and search/alarm search comamnds.
3. Replies to userspace commands.

From: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Special file in each w1 slave device's directory called "rw" is created
each time new slave and no appropriate w1 family is registered.
"rw" file supports read and write operations, which allows to perform
almost any kind of operations. Each logical operation is a transaction
in nature, which can contain several (two or one) low-level operations.
Let's see how one can read EEPROM context:
1. one must write control buffer, i.e. buffer containing command byte
and two byte address. At this step bus is reset and appropriate device
is selected using either W1_SKIP_ROM or W1_MATCH_ROM command.
Then provided control buffer is being written to the wire.
2. reading. This will issue reading eeprom response.

It is possible that between 1. and 2. w1 master thread will reset bus for
searching and slave device will be even removed, but in this case 0xff will
be read, since no device was selected.
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I2C creates some sysfs nodes in the wrong places:  not as children of parent
controllers, but as their peers (!).  This puts them into the right place
always, instead of just when the adapter is on the platform bus.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for two new VID codes, supporting Intel mobile Core
processors and new Conroe based platforms.
Signed-off-by: NRudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver implements support for the National Semiconductor LM70
temperature sensor.

The LM70 temperature sensor chip supports a single temperature sensor.
It communicates with a host processor (or microcontroller) via an
SPI/Microwire Bus interface.

Communication with the LM70 is simple: when the temperature is to be sensed,
the driver accesses the LM70 using SPI communication: 16 SCLK cycles
comprise the MOSI/MISO loop. At the end of the transfer, the 11-bit 2's
complement digital temperature (sent via the SIO line), is available in the
driver for interpretation. This driver makes use of the kernel's in-core
SPI support.
Signed-off-by: NKaiwan N Billimoria <kaiwan@designergraphix.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Hardware monitoring chips don't have to be on the I2C bus.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

i2c-i801: Merge setup function

Merge i801_setup into i801_probe, as it doesn't make much sense to
have them split. This lets us handle errors better. Christopher
Hellwig had been suggesting this back in March 2003 when the driver
was merged.

Also drop two useless debug messages (revision and base address can be
obtained from lspci, procfs or sysfs.)
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

i2c-i801: Better pci subsystem integration

Integrate the i2c-i801 driver better with the pci subsystem, by
calling pci_{enable,disable}_device and requesting the I/O region
by BAR rather than direct configuration space access.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

i2c-i801: Cleanups

Various cleanups to the i2c-i801 driver:
* Fix documentation file and self file name references.
* i801_setup can be marked __devinit.
* Drop useless error local variable and label in i801_setup.
* Avoid a double PCI configuration register write in some cases.
* Use symbolic names for SMBHSTCFG bits.
* Transmit the error code returned by i801_setup instead of forcing it
  to an arbitrary value.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

i2c-i801: Remove PCI function check

Remove the PCI function number check when probing devices.
This check is redundant, each function has a separate PCI device
ID, so checking for that ID is sufficient.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

i2c-i801: Remove force_addr parameter

Remove the force_addr module parameter. It doesn't appear to ever
have been needed, and PCI resources shouldn't be arbitrarily
changed anyway.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

i2c-i801: Fix block transaction poll loops

Two of the three poll loops have the poll and sleep swapped,
causing an extra sleep to occur after the polled condition is
fulfilled. In practice, this doubles the amount of sleep time for
every block transaction.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In i2c bus driver scx200_acb, function scx200_acb_probe can be
tagged __init.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On the CS5535 and CS5536, the I/O resource is allocated through PCI,
so use that instead of using the MSR backdoor.
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The attached patch marks i2c_smbus_write_block_data() and
i2c_smbus_write_i2c_block_data() buffers as const.
Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Minor cleanup to the i2c-ocores driver.

Peter Korsgaard will maintain the i2c-ocores driver.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

One of my testers had a problem where the driver only saw 2 of the 4 fan
sensors his uGuru has, this fixes this.
 -accept 0x40 (bit 6) being high as a valid fan sensor setting for all fans
  not just fan 1, I have a feeling this bit indicates whether or not a fan is
  actually connected .
Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>