_transceiver() in otg.c is replaced with _phy. usb_set_transceiver is
replaced with usb_add_phy to make it similar to other usb standard
function names like usb_add_hcd.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Currently usb_put_transceiver calls put_device so this is a no-op but it
is better to keep API usage consistent as ehci->transceiver is allocated
with usb_get_transceiver.

While at there remove one extra ehci->transceiver test as the code block
has already tested it.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit 28c56ea1
(powerpc/usb: fix bug of kernel hang when initializing usb)
the kernel crashes on mpc5121e. mpc5121e doesn't have system interface
registers, accessing this register address space cause the machine check
exception and a kernel crash:
...
[    1.294596] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.316491] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[    1.337334] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[    1.358548] Machine check in kernel mode.
[    1.375917] Caused by (from SRR1=49030): Transfer error ack signal
[    1.395505] Oops: Machine check, sig: 7 [#1]
[    1.413113] MPC5121 ADS
[    1.428718] Modules linked in:
[    1.444841] NIP: c026efc4 LR: c0278b50 CTR: 00000000
[    1.463342] REGS: df837ba0 TRAP: 0200   Not tainted  (3.3.0-08839-gb5174fa3)
[    1.484083] MSR: 00049030 <EE,ME,IR,DR>  CR: 42042022  XER: 20000000
[    1.504099] TASK = df834000[1] 'swapper' THREAD: df836000
[    1.509667] GPR00: 1c000000 df837c50 df834000 df9d74e0 00000003 00000010 00000000 00000000
[    1.531650] GPR08: 00000020 00000000 c037cdd8 e1088000 22042028 1001a69c 00000000 00000000
[    1.553762] GPR16: 1ffbce70 00000000 1fef5b28 1fef3e08 00000000 00000000 1ffcbc7c c045b264
[    1.575824] GPR24: 0000008b 00000002 c04a7dd0 e1088000 df33c960 df9d74e0 00000000 df9d7400
[    1.612295] NIP [c026efc4] ehci_fsl_setup_phy+0x110/0x124
[    1.632454] LR [c0278b50] ehci_fsl_setup+0x29c/0x304
[    1.652065] Call Trace:
[    1.668923] [df837c50] [c0278a40] ehci_fsl_setup+0x18c/0x304 (unreliable)
[    1.690332] [df837c70] [c025cba4] usb_add_hcd+0x1f0/0x66c
[    1.710377] [df837cb0] [c0277ab8] ehci_fsl_drv_probe+0x180/0x308
[    1.731322] [df837ce0] [c01fc7a8] platform_drv_probe+0x20/0x30
[    1.752202] [df837cf0] [c01fb0ac] driver_probe_device+0x8c/0x214
[    1.773491] [df837d10] [c01f956c] bus_for_each_drv+0x6c/0xa8
[    1.794279] [df837d40] [c01fafdc] device_attach+0xb4/0xd8
[    1.814574] [df837d60] [c01fa44c] bus_probe_device+0xa4/0xb4
[    1.835343] [df837d80] [c01f87a8] device_add+0x52c/0x5dc
[    1.855462] [df837dd0] [c01fcd58] platform_device_add+0x124/0x1d0
[    1.876558] [df837df0] [c036dcec] fsl_usb2_device_register+0xa0/0xd4
[    1.897512] [df837e10] [c036df28] fsl_usb2_mph_dr_of_probe+0x208/0x264
[    1.918253] [df837e90] [c01fc7a8] platform_drv_probe+0x20/0x30
[    1.938300] [df837ea0] [c01fb0ac] driver_probe_device+0x8c/0x214
[    1.958511] [df837ec0] [c01fb2f0] __driver_attach+0xbc/0xc0
[    1.978088] [df837ee0] [c01f9608] bus_for_each_dev+0x60/0x9c
[    1.997589] [df837f10] [c01fab88] driver_attach+0x24/0x34
[    2.016757] [df837f20] [c01fa744] bus_add_driver+0x1ac/0x274
[    2.036339] [df837f50] [c01fb898] driver_register+0x88/0x150
[    2.056052] [df837f70] [c01fcabc] platform_driver_register+0x68/0x78
[    2.076650] [df837f80] [c0446500] fsl_usb2_mph_dr_driver_init+0x18/0x28
[    2.097734] [df837f90] [c0003988] do_one_initcall+0x148/0x1b0
[    2.117934] [df837fc0] [c042d89c] kernel_init+0xfc/0x190
[    2.137667] [df837ff0] [c000d2c4] kernel_thread+0x4c/0x68
[    2.157240] Instruction dump:
[    2.174119] 90050004 4e800020 2f840003 419e0014 2f840004 409eff64 6400c000 4bffff5c
[    2.196000] 64001000 7c0004ac 812b0500 0c090000 <4c00012c> 61290200 7c0004ac 912b0500
[    2.218100] ---[ end trace 21659aedb84ad816 ]---
[    2.237089]
[    3.232940] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007
[    3.232954]
[    3.271575] Rebooting in 1 seconds..

Check pdata->have_sysif_regs flag before accessing system interface
registers.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for ULPI and UTMI PHYs based on usb controller
version info read from device-tree

Example of USB Controller versioning info:
Version 1.2 and below : MPC8536, MPC8315, etc
Version 1.6 : P1020, P1010, P2020, P5020, etc
Version 2.2 : PSC9131, PSC9132, P3060, etc

No changes for non-DT users
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 529febee.

To quote Dirk:
	This commit introduces a check for the USB PHY clock.
	Problem is that CTRL_PHY_CLK_VALID bit seems not to be present
	on all Freescale ehci implementations, at least P1022 does not
	have it.  So this check always fails and the driver never gets
	loaded.

So we need to revert this patch.
Reported-by: NDirk Eibach <Eibach@gdsys.de>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 79857e8e.

To quote Shengzhou Liu:
	I'm sorry, please don't apply this patch.
	It appears not only on P1022 platform.
	There will be more breaks on other platforms regarding
	CTRL_PHY_CLK_VALID bit.
	I will post a new patch with well compatibility on all
	platforms as soon as I get necessary confirmations.

Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix checking of CTRL_PHY_CLK_VALID bit break on some platform on which
there is not USB CTRL_PHY_CLK_VALID bit.
  - P1023/P3041/P5020 etc,have this bit
  - P3060/4080/PSC913x do have this bit, but not mentioned in RM.
  - P1022(perhaps and other) has no this bit
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This changes the otg functions so that they receive struct
otg instead of struct usb_phy as parameter and
converts all users of these functions to pass the otg member
of their usb_phy.

Includes fixes to IMX code from Sascha Hauer.

[ balbi@ti.com : fixed a compile warning on ehci-mv.c ]
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Acked-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: NLi Yang <leoli@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the new usb_phy_* functions with transceiver
operations instead of the old otg functions.

Includes fixes from Sascha Hauer.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: NLi Yang <leoli@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If USB UTMI PHY is not enable, writing to portsc register will lead to
kernel hang during boot up.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Reported-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If a MPC8xxx was being used, 'have_sysif_regs' should be set and
it should setup cache snooping for all the 4GB space on both PPC32
and PPC64.
Signed-off-by: NPan Jiafei <Jiafei.Pan@freescale.com>
Acked-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

when missing USB PHY clock, kernel booting up will halt during USB
initialization. We should check USBGP[PHY_CLK_VALID] bit to avoid
CPU hang in this case.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use INCR8 mode for system bus interface of the USB controller
on MPC512x. This is a work-around for the AHB bus lock up
problem observed on MPC512x when there is heavy simultaneous
PATA write or network (FEC) activity.

See also "12.4 The USB controller can issue transactions that lock
up the AHB bus under certain conditions" in MPC5121e (M36P) Errata.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Tested-by: NMatthias Fuchs <matthias.fuchs@esd.ue>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
    when != iounmap(e)
*if (...)
   { ... when != iounmap(e)
     return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This flag is a NOOP and can be removed now.
Signed-off-by: NYong Zhang <yong.zhang0@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1483) improves the ehci-hcd driver family by getting rid
of the reliance on the hcd->state variable.  It has no clear owner and
it isn't protected by the usual HCD locks.  In its place, the patch
adds a new, private ehci->rh_state field to record the state of the
root hub.

Along the way, the patch removes a couple of lines containing
redundant assignments to the state variable.  Also, the QUIESCING
state simply gets changed to the RUNNING state, because the driver
doesn't make any distinction between them.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Several fixes as well where the +1 was missing.

Done via coccinelle scripts like:

@@
struct resource *ptr;
@@

- ptr->end - ptr->start + 1
+ resource_size(ptr)

and some grep and typing.

Mostly uncompiled, no cross-compilers.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The two first HC capability registers (CAPLENGTH and HCIVERSION)
are defined as one 8-bit and one 16-bit register. Most HC
implementations have selected to treat these registers as part
of a 32-bit register, giving the same layout for both big and
small endian systems.

This patch adds a new quirk, big_endian_capbase, to support
controllers with big endian register interfaces that treat
HCIVERSION and CAPLENGTH as individual registers.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Previously a check was done on an ID register at the base of a CPU's
internal USB registers to determine if system interface regsiters were
present.  The check looked for an ID register that had the format
ID[0:5] == ~ID[8:13] as described in the MPC5121 User's Manual to
determine if a MPC5121 or MPC83xx/85xx was being used.

There are two issues with this method:
- The ID register is not defined on the MPC83xx/85xx CPUs, so its
  unclear what is being checked on them.
- Newer CPUs such as the P4080 also don't document the ID register, but
  do share the same format as the MPC5121.  Thus the previous code did
  not set 'have_sysif_regs' properly which results in the P4080 not
  properly initializing its USB ports.

Using the device tree 'compatible' node is a cleaner way to determine if
'have_sysif_regs' should be set and resolves the USB initialization issue
seen on the P4080.

Tested on a P4080-based system and compile tested on mpc512x_defconfig
with Freescale EHCI driver enabled.

Cc: Anatolij Gustschin <agust@denx.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Extends FSL EHCI platform driver glue layer to support
MPC5121 USB controllers. MPC5121 Rev 2.0 silicon EHCI
registers are in big endian format. The appropriate flags
are set using the information in the platform data structure.
MPC83xx system interface registers are not available on
MPC512x, so the access to these registers is isolated in
MPC512x case. Furthermore the USB controller clocks
must be enabled before 512x register accesses which is
done by providing platform specific init callback.

The MPC512x internal USB PHY doesn't provide supply voltage.
For boards using different power switches allow specifying
DRVVBUS and PWR_FAULT signal polarity of the MPC5121 internal
PHY using "fsl,invert-drvvbus" and "fsl,invert-pwr-fault"
properties in the device tree USB nodes. Adds documentation
for this new device tree bindings.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

tdi_reset is already taking care of setting host mode for tdi devices.
Don't duplicate code in platform driver.

Make ehci_halt a nop if the controller is not in host mode (otherwise it 
will fail), and let's ehci_reset do the tdi_reset.
We need to move hcd->has_tt flags before ehci_halt, in order ehci_halt 
knows we are a tdi device.


Before the setup routine was doing :
- put controller in host mode
- ehci_halt
- ehci_init
- hcd->has_tt = 1;
- ehci_reset

Now we do :
- hcd->has_tt = 1;
- ehci_halt
- ehci_init
- ehci_reset

PS : now we handle correctly the device -> host transition.
Signed-off-by: NMatthieu CASTET <matthieu.castet@parrot.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1385) adds a "do_wakeup" parameter to the pci_suspend
method used by PCI-based host controller drivers.  ehci-hcd in
particular needs to know whether or not to enable wakeup when
suspending a controller.  Although that information is currently
available through device_may_wakeup(), when support is added for
runtime suspend this will no longer be true.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1380) fixes a bug in the wakeup settings for EHCI host
controllers.  When the controller is suspended, if it isn't enabled
for remote wakeup then we have to turn off all the port wakeup flags.
Disabling PCI PME# isn't good enough, because some systems (Intel)
evidently use alternate wakeup signalling paths.

In addition, the patch improves the handling of the Intel Moorestown
hardware by performing various power-up and power-down delays just
once instead of once for each port (i.e., the delays are moved outside
of the port loops).  This requires extra code, but the total delay
time is reduced.

There are also a few additional minor cleanups.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NOndrej Zary <linux@rainbow-software.org>
CC: Alek Du <alek.du@intel.com>
CC: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

EHCI FSL controller preserve its state during sleep mode, so nothing
fancy needs to be done.

Though, during 'deep sleep' mode (as found in MPC831x CPUs) the
controller turns off and needs to be reinitialized upon resume.

This patch adds support for hibernation and resuming after deep sleep.
Based on Dave Liu and Jerry Huang's work[1].

[1] http://www.bitshrine.org/gpp/linux-fsl-2.6.24.3-MPC8315ERDB-usb-power-mangement.patchSigned-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes following warnings:

ehci-fsl.c:43:5: warning: symbol 'usb_hcd_fsl_probe' was not declared. Should it be static?
ehci-fsl.c:150:6: warning: symbol 'usb_hcd_fsl_remove' was not declared. Should it be static?
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1256) changes ehci-hcd and all the other drivers in the
EHCI family to make use of the new clear_tt_buffer callbacks.  When a
Clear-TT-Buffer request is in progress for a QH, the QH is not allowed
to be linked into the async schedule until the request is finished.
At that time, if there are any URBs queued for the QH, it is linked
into the async schedule.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1245) fixes a bug in ehci-hcd.  When an URB is queued
for an endpoint whose QH is already in the LINKED state, the QH
doesn't get refreshed.  As a result, if usb_clear_halt() was called
during the time that the QH was linked but idle, the data toggle value
in the QH doesn't get reset.

The symptom is that after a clear_halt, data gets lost and transfers
time out.  This problem is starting to show up now because the
"ehci-hcd unlink speedups" patch causes QHs with no queued URBs to
remain linked for a suitable time.

The patch utilizes the new endpoint_reset mechanism to fix the
problem.  When an endpoint is reset, the new method forcibly unlinks
the QH (if necessary) and safely updates the toggle value.  This
allows qh_update() to be simplified and avoids using usb_device's
toggle bits in a rather unintuitive way.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: NDavid <david@unsolicited.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A couple of USB register initializations had to be changed on MPC85xx
platforms.  This is due to the internal SoC buses being different on
MPC83xx SoCs vs MPC85xx SoCs.

We currently handle this via an ifdef since 83xx and 85xx are mutually
exclusive kernel builds.
Signed-off-by: NSrikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The bus_id field is going away, use the dev_name() function instead.
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1096) fixes an annoying problem: When a full-speed or
low-speed device is plugged into an EHCI controller, it fails to
enumerate at high speed and then is handed over to the companion
controller.  But usbcore logs a misleading and unwanted error message
when the high-speed enumeration fails.

The patch adds a new HCD method, port_handed_over, which asks whether
a port has been handed over to a companion controller.  If it has, the
error message is suppressed.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1095) cleans up the HCD glue and several of the EHCI
bus-glue files.  The ehci->is_tdi_rh_tt flag is redundant, since it
means the same thing as the hcd->has_tt flag, so it is removed and the
other flag used in its place.

Some of the bus-glue files didn't get the relinquish_port method added
to their hc_driver structures.  Although that routine currently
doesn't do anything for controllers with an integrated TT, in the
future it might.  So the patch adds it where it is missing.

Lastly, some of the bus-glue files have erroneous entries for their
hc_driver's suspend and resume methods.  These method pointers are
specific to PCI and shouldn't be used otherwise.

(The patch also includes an invisible whitespace fix.)
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>

Various minor fixes to some SOC bus glue for EHCI:

 - Remove a bogus copyright (by "me"!) which someone added to the FSL
   driver, and an irrelevant comment.

 - Un-break MODULE_ALIAS() directives after platform_bus hotplugging
   acquired a backwards-incompatible change.  (Which didn't fix ANY
   of the in-tree drivers it prevented from hotplugging -- sigh.)

 - Remove some bogus assignments of platform_bus_type; that's done by
   the platform_bus code.

 - Add some FIXMEs for drivers with that pointless two-level idiom for
   probe() and remove() routines.  ("Obfuscation" is a non-goal.)
   That should help avoid future bus glue which copies that idiom.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch hands over the port to the companion when the
hub_port_connect_change fails.
Signed-off-by: NBalaji Rao <balajirrao@gmail.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Host controller IRQs are supposed to be serviced with interrupts
disabled.  This patch (as1026) adds an IRQF_DISABLED flag to all the
controller drivers that lack it.  It also replaces the
spin_lock_irqsave() and spin_unlock_irqrestore() calls in uhci_irq()
with simple spin_lock() and spin_unlock().

This fixes Bugzilla #9335.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For MPC831x support, change the ehci-fsl driver to preserve
bits set in platform code.  Add a common CONFIG_USB_EHCI_FSL
to indicate presence of Freescale EHCI SOC.  Add FSL_USB2_DR_OTG
operating mode support, thus both host and device can work for the
mini-ab receptacle.  Note: this doesn't enable OTG protocol
support.
Signed-off-by: NLi Yang <leoli@freescale.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The patch fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=7482.

It sets USB snooping on 4G space for PowerPC platforms without
CONFIG_NOT_COHERENT_CACHE defined.
Reported-by: NStefan Meyer <reyems@telkomsa.net>
Signed-off-by: NLi Yang <leoli@freescale.com>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch implements supports for EHCI controllers whose MMIO
registers are big endian and enables that functionality for
the Toshiba SCC chip. It does _not_ add support for big endian
in-memory data structures as this is not needed for that chip
and I hope it will never be.

The guts of the patch are to convert readl(...) to
ehci_readl(ehci, ...) and similarly for register writes.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>