The in_irq() check in rcu_enter_nohz() is redundant because if we really
are in an interrupt, the attempt to re-enter dyntick-idle mode will invoke
rcu_needs_cpu() in any case, which will force the check for RCU callbacks.
So this commit removes the check along with the set_need_resched().
Suggested-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

RCU no longer uses this global variable, nor does anyone else.  This
commit therefore removes this variable.  This reduces memory footprint
and also removes some atomic instructions and memory barriers from
the dyntick-idle path.
Signed-off-by: NAlex Shi <alex.shi@intel.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

When rcutorture is compiled directly into the kernel
(instead of separately as a module), it is necessary to specify
rcutorture.stat_interval as a kernel command-line parameter, otherwise,
the rcu_torture_stats kthread is never started.  However, when working
with the system after it has booted, it is convenient to be able to
change the time between statistic printing, particularly when logged
into the console.

This commit therefore allows the stat_interval parameter to be changed
at runtime.
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

There is often a delay between the time that a CPU passes through a
quiescent state and the time that this quiescent state is reported to the
RCU core.  It is quite possible that the grace period ended before the
quiescent state could be reported, for example, some other CPU might have
deduced that this CPU passed through dyntick-idle mode.  It is critically
important that quiescent state be counted only against the grace period
that was in effect at the time that the quiescent state was detected.

Previously, this was handled by recording the number of the last grace
period to complete when passing through a quiescent state.  The RCU
core then checks this number against the current value, and rejects
the quiescent state if there is a mismatch.  However, one additional
possibility must be accounted for, namely that the quiescent state was
recorded after the prior grace period completed but before the current
grace period started.  In this case, the RCU core must reject the
quiescent state, but the recorded number will match.  This is handled
when the CPU becomes aware of a new grace period -- at that point,
it invalidates any prior quiescent state.

This works, but is a bit indirect.  The new approach records the current
grace period, and the RCU core checks to see (1) that this is still the
current grace period and (2) that this grace period has not yet ended.
This approach simplifies reasoning about correctness, and this commit
changes over to this new approach.
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

Add trace events to record grace-period start and end, quiescent states,
CPUs noticing grace-period start and end, grace-period initialization,
call_rcu() invocation, tasks blocking in RCU read-side critical sections,
tasks exiting those same critical sections, force_quiescent_state()
detection of dyntick-idle and offline CPUs, CPUs entering and leaving
dyntick-idle mode (except from NMIs), CPUs coming online and going
offline, and CPUs being kicked for staying in dyntick-idle mode for too
long (as in many weeks, even on 32-bit systems).
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

rcu: Add the rcu flavor to callback trace events

The earlier trace events for registering RCU callbacks and for invoking
them did not include the RCU flavor (rcu_bh, rcu_preempt, or rcu_sched).
This commit adds the RCU flavor to those trace events.
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

This patch #ifdefs TINY_RCU kthreads out of the kernel unless RCU_BOOST=y,
thus eliminating context-switch overhead if RCU priority boosting has
not been configured.
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

Add event-trace markers to TREE_RCU kthreads to allow including these
kthread's CPU time in the utilization calculations.
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

Andi Kleen noticed that one of the RCU_BOOST data declarations was
out of sync with the definition.  Move the declarations so that the
compiler can do the checking in the future.
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

We now have kthreads only for flavors of RCU that support boosting,
so update the now-misleading comments accordingly.
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

Add a string to the rcu_batch_start() and rcu_batch_end() trace
messages that indicates the RCU type ("rcu_sched", "rcu_bh", or
"rcu_preempt").  The trace messages for the actual invocations
themselves are not marked, as it should be clear from the
rcu_batch_start() and rcu_batch_end() events before and after.
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

In order to allow event tracing to distinguish between flavors of
RCU, we need those names in the relevant RCU data structures.  TINY_RCU
has avoided them for memory-footprint reasons, so add them only if
CONFIG_RCU_TRACE=y.
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

This commit adds the trace_rcu_utilization() marker that is to be
used to allow postprocessing scripts compute RCU's CPU utilization,
give or take event-trace overhead.  Note that we do not include RCU's
dyntick-idle interface because event tracing requires RCU protection,
which is not available in dyntick-idle mode.
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

There was recently some controversy about the overhead of invoking RCU
callbacks.  Add TRACE_EVENT()s to obtain fine-grained timings for the
start and stop of a batch of callbacks and also for each callback invoked.
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

The rcu_torture_boost() cleanup code destroyed debug-objects state before
waiting for the last RCU callback to be invoked, resulting in rare but
very real debug-objects warnings.  Move the destruction to after the
waiting to fix this problem.
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

Now that the RCU API contains synchronize_rcu_bh(), synchronize_sched(),
call_rcu_sched(), and rcu_bh_expedited()...

Make rcutorture test synchronize_rcu_bh(), getting rid of the old
rcu_bh_torture_synchronize() workaround.  Similarly, make rcutorture test
synchronize_sched(), getting rid of the old sched_torture_synchronize()
workaround.  Make rcutorture test call_rcu_sched() instead of wrappering
synchronize_sched().  Also add testing of rcu_bh_expedited().
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

Pull the code that waits for an RCU grace period into a single function,
which is then called by synchronize_rcu() and friends in the case of
TREE_RCU and TREE_PREEMPT_RCU, and from rcu_barrier() and friends in
the case of TINY_RCU and TINY_PREEMPT_RCU.
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

rcutree.c defines rcu_cpu_kthread_cpu as int, not unsigned int,
so the extern has to follow that.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

Long ago, using TREE_RCU with PREEMPT would result in "scheduling
while atomic" diagnostics if you blocked in an RCU read-side critical
section.  However, PREEMPT now implies TREE_PREEMPT_RCU, which defeats
this diagnostic.  This commit therefore adds a replacement diagnostic
based on PROVE_RCU.

Because rcu_lockdep_assert() and lockdep_rcu_dereference() are now being
used for things that have nothing to do with rcu_dereference(), rename
lockdep_rcu_dereference() to lockdep_rcu_suspicious() and add a third
argument that is a string indicating what is suspicious.  This third
argument is passed in from a new third argument to rcu_lockdep_assert().
Update all calls to rcu_lockdep_assert() to add an informative third
argument.

Also, add a pair of rcu_lockdep_assert() calls from within
rcu_note_context_switch(), one complaining if a context switch occurs
in an RCU-bh read-side critical section and another complaining if a
context switch occurs in an RCU-sched read-side critical section.
These are present only if the PROVE_RCU kernel parameter is enabled.

Finally, fix some checkpatch whitespace complaints in lockdep.c.

Again, you must enable PROVE_RCU to see these new diagnostics.  But you
are enabling PROVE_RCU to check out new RCU uses in any case, aren't you?
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

There are a number of cases where the RCU can find additional work
for the per-CPU kthread within the context of that per-CPU kthread.
In such cases, the per-CPU kthread is already running, so attempting
to wake itself up does nothing except waste CPU cycles.  This commit
therefore checks to see if it is in the per-CPU kthread context,
omitting the wakeup in this case.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

Commit a26ac245 (move TREE_RCU from softirq to kthread) added
per-CPU kthreads.  However, kthread creation uses kthread_create(), which
can put the kthread's stack and task struct on the wrong NUMA node.
Therefore, use kthread_create_on_node() instead of kthread_create()
so that the stacks and task structs are placed on the correct NUMA node.

A similar change was carried out in commit 94dcf29a (kthread:
use kthread_create_on_node()).

Also change rcutorture's priority-boost-test kthread creation.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Tejun Heo <tj@kernel.org>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Andi Kleen <ak@linux.intel.com>
CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

If PTRACE_LISTEN fails after lock_task_sighand() it doesn't drop ->siglock.
Reported-by: NMatt Fleming <matt.fleming@intel.com>
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Even with just the interface limited to admin, there really is little to
reason to give byte-per-byte counts for taskstats.  So round it down to
something less intrusive.
Acked-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Ok, this isn't optimal, since it means that 'iotop' needs admin
capabilities, and we may have to work on this some more.  But at the
same time it is very much not acceptable to let anybody just read
anybody elses IO statistics quite at this level.

Use of the GENL_ADMIN_PERM suggested by Johannes Berg as an alternative
to checking the capabilities by hand.
Reported-by: NVasiliy Kulikov <segoon@openwall.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Acked-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Take cwq->gcwq->lock to avoid racing between drain_workqueue checking to
make sure the workqueues are empty and cwq_dec_nr_in_flight decrementing
and then incrementing nr_active when it activates a delayed work.

We discovered this when a corner case in one of our drivers resulted in
us trying to destroy a workqueue in which the remaining work would
always requeue itself again in the same workqueue.  We would hit this
race condition and trip the BUG_ON on workqueue.c:3080.
Signed-off-by: NThomas Tuttle <ttuttle@chromium.org>
Acked-by: NTejun Heo <tj@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If an irq_chip provides .irq_shutdown(), but neither of .irq_disable() or
.irq_mask(), free_irq() crashes when jumping to NULL.
Fix this by only trying .irq_disable() and .irq_mask() if there's no
.irq_shutdown() provided.

This revives the symmetry with irq_startup(), which tries .irq_startup(),
.irq_enable(), and irq_unmask(), and makes it consistent with the comment for
irq_chip.irq_shutdown() in <linux/irq.h>, which says:

 * @irq_shutdown:	shut down the interrupt (defaults to ->disable if NULL)

This is also how __free_irq() behaved before the big overhaul, cfr. e.g.
3b56f058 ("genirq: Remove bogus conditional"),
where the core interrupt code always overrode .irq_shutdown() to
.irq_disable() if .irq_shutdown() was NULL.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Link: http://lkml.kernel.org/r/1315742394-16036-2-git-send-email-geert@linux-m68k.org
Cc: stable@kernel.org
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

We detected a serious issue with PERF_SAMPLE_READ and
timing information when events were being multiplexing.

Samples would have time_running > time_enabled. That
was easy to reproduce with a libpfm4 example (ran 3
times to cause multiplexing on Core 2):

 $ syst_smpl -e uops_retired:freq=1 &
 $ syst_smpl -e uops_retired:freq=1 &
 $ syst_smpl -e uops_retired:freq=1 &
 IIP:0x0000000040062d ... PERIOD:2355332948 ENA=40144625315 RUN=60014875184
 syst_smpl: WARNING: time_running > time_enabled
	63277537998 uops_retired:freq=1 , scaled

The bug was not present in kernel up to (and including) 3.0. It turns
out the bug was introduced by the following commit:

commit c4794295

    events: Move lockless timer calculation into helper function

The parameters of the function got reversed yet the call sites
were not updated to reflect the change. That lead to time_running
and time_enabled being swapped. That had no effect when there was
no multiplexing because in that case time_running = time_enabled
but it would show up in any other scenario.
Signed-off-by: NStephane Eranian <eranian@google.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110829124112.GA4828@quadSigned-off-by: NIngo Molnar <mingo@elte.hu>

The current cgroup context switch code was incorrect leading
to bogus counts. Furthermore, as soon as there was an active
cgroup event on a CPU, the context switch cost on that CPU
would increase by a significant amount as demonstrated by a
simple ping/pong example:

 $ ./pong
 Both processes pinned to CPU1, running for 10s
 10684.51 ctxsw/s

Now start a cgroup perf stat:
 $ perf stat -e cycles,cycles -A -a -G test  -C 1 -- sleep 100

$ ./pong
 Both processes pinned to CPU1, running for 10s
 6674.61 ctxsw/s

That's a 37% penalty.

Note that pong is not even in the monitored cgroup.

The results shown by perf stat are bogus:
 $ perf stat -e cycles,cycles -A -a -G test  -C 1 -- sleep 100

 Performance counter stats for 'sleep 100':

 CPU1 <not counted> cycles   test
 CPU1 16,984,189,138 cycles  #    0.000 GHz

The second 'cycles' event should report a count @ CPU clock
(here 2.4GHz) as it is counting across all cgroups.

The patch below fixes the bogus accounting and bypasses any
cgroup switches in case the outgoing and incoming tasks are
in the same cgroup.

With this patch the same test now yields:
 $ ./pong
 Both processes pinned to CPU1, running for 10s
 10775.30 ctxsw/s

Start perf stat with cgroup:

 $ perf stat -e cycles,cycles -A -a -G test  -C 1 -- sleep 10

Run pong outside the cgroup:
 $ /pong
 Both processes pinned to CPU1, running for 10s
 10687.80 ctxsw/s

The penalty is now less than 2%.

And the results for perf stat are correct:

$ perf stat -e cycles,cycles -A -a -G test  -C 1 -- sleep 10

 Performance counter stats for 'sleep 10':

 CPU1 <not counted> cycles test #    0.000 GHz
 CPU1 23,933,981,448 cycles      #    0.000 GHz

Now perf stat reports the correct counts for
for the non cgroup event.

If we run pong inside the cgroup, then we also get the
correct counts:

$ perf stat -e cycles,cycles -A -a -G test  -C 1 -- sleep 10

 Performance counter stats for 'sleep 10':

 CPU1 22,297,726,205 cycles test #    0.000 GHz
 CPU1 23,933,981,448 cycles      #    0.000 GHz

      10.001457237 seconds time elapsed
Signed-off-by: NStephane Eranian <eranian@google.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110825135803.GA4697@quadSigned-off-by: NIngo Molnar <mingo@elte.hu>

This patch fixes the following memory leak:

unreferenced object 0xffff880107266800 (size 512):
  comm "sched-powersave", pid 3718, jiffies 4323097853 (age 27495.450s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff81133940>] create_object+0x187/0x28b
    [<ffffffff814ac103>] kmemleak_alloc+0x73/0x98
    [<ffffffff811232ba>] __kmalloc_node+0x104/0x159
    [<ffffffff81044b98>] kzalloc_node.clone.97+0x15/0x17
    [<ffffffff8104cb90>] build_sched_domains+0xb7/0x7f3
    [<ffffffff8104d4df>] partition_sched_domains+0x1db/0x24a
    [<ffffffff8109ee4a>] do_rebuild_sched_domains+0x3b/0x47
    [<ffffffff810a00c7>] rebuild_sched_domains+0x10/0x12
    [<ffffffff8104d5ba>] sched_power_savings_store+0x6c/0x7b
    [<ffffffff8104d5df>] sched_mc_power_savings_store+0x16/0x18
    [<ffffffff8131322c>] sysdev_class_store+0x20/0x22
    [<ffffffff81193876>] sysfs_write_file+0x108/0x144
    [<ffffffff81135b10>] vfs_write+0xaf/0x102
    [<ffffffff81135d23>] sys_write+0x4d/0x74
    [<ffffffff814c8a42>] system_call_fastpath+0x16/0x1b
    [<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: NWANG Cong <amwang@redhat.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: stable@kernel.org # 3.0
Link: http://lkml.kernel.org/r/1313671017-4112-1-git-send-email-amwang@redhat.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

There is no real reason to run blk_schedule_flush_plug() with
interrupts and preemption disabled.

Move it into schedule() and call it when the task is going voluntarily
to sleep. There might be false positives when the task is woken
between that call and actually scheduling, but that's not really
different from being woken immediately after switching away.

This fixes a deadlock in the scheduler where the
blk_schedule_flush_plug() callchain enables interrupts and thereby
allows a wakeup to happen of the task that's going to sleep.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@kernel.org # 2.6.39+
Link: http://lkml.kernel.org/n/tip-dwfxtra7yg1b5r65m32ywtct@git.kernel.orgSigned-off-by: NIngo Molnar <mingo@elte.hu>

Block-IO and workqueues call into notifier functions from the
scheduler core code with interrupts and preemption disabled. These
calls should be made before entering the scheduler core.

To simplify this, separate the scheduler core code into
__schedule(). __schedule() is directly called from the places which
set PREEMPT_ACTIVE and from schedule(). This allows us to add the work
checks into schedule(), so they are only called when a task voluntary
goes to sleep.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@kernel.org # 2.6.39+
Link: http://lkml.kernel.org/r/20110622174918.813258321@linutronix.deSigned-off-by: NIngo Molnar <mingo@elte.hu>

The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It seems that 7bf69395 ("console: allow to retain boot console via
boot option keep_bootcon") doesn't always achieve what it aims, as when
printk_late_init() runs it unconditionally turns off all boot consoles.
With this patch, I am able to see more messages on the boot console in
KVM guests than I can without, when keep_bootcon is specified.

I think it is appropriate for the relevant -stable trees.  However, it's
more of an annoyance than a serious bug (ideally you don't need to keep
the boot console around as console handover should be working -- I was
encountering a situation where the console handover wasn't working and
not having the boot console available meant I couldn't see why).
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg KH <gregkh@suse.de>
Acked-by: NFabio M. Di Nitto <fdinitto@redhat.com>
Cc: <stable@kernel.org>		[2.6.39.x, 3.0.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I ran into a couple of programs which broke with the new Linux 3.0
version.  Some of those were binary only.  I tried to use LD_PRELOAD to
work around it, but it was quite difficult and in one case impossible
because of a mix of 32bit and 64bit executables.

For example, all kind of management software from HP doesnt work, unless
we pretend to run a 2.6 kernel.

  $ uname -a
  Linux svivoipvnx001 3.0.0-08107-g97cd98f #1062 SMP Fri Aug 12 18:11:45 CEST 2011 i686 i686 i386 GNU/Linux

  $ hpacucli ctrl all show

  Error: No controllers detected.

  $ rpm -qf /usr/sbin/hpacucli
  hpacucli-8.75-12.0

Another notable case is that Python now reports "linux3" from
sys.platform(); which in turn can break things that were checking
sys.platform() == "linux2":

  https://bugzilla.mozilla.org/show_bug.cgi?id=664564

It seems pretty clear to me though it's a bug in the apps that are using
'==' instead of .startswith(), but this allows us to unbreak broken
programs.

This patch adds a UNAME26 personality that makes the kernel report a
2.6.40+x version number instead.  The x is the x in 3.x.

I know this is somewhat ugly, but I didn't find a better workaround, and
compatibility to existing programs is important.

Some programs also read /proc/sys/kernel/osrelease.  This can be worked
around in user space with mount --bind (and a mount namespace)

To use:

  wget ftp://ftp.kernel.org/pub/linux/kernel/people/ak/uname26/uname26.c
  gcc -o uname26 uname26.c
  ./uname26 program
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit f3637a5f.

It turns out that this breaks several drivers, one example being OMAP
boards which use the on-board OMAP UARTs and the omap-serial driver that
will not boot to userspace after the commit.

Paul Walmsley reports that enabling CONFIG_DEBUG_SHIRQ reveals 'IRQ
handler type mismatch' errors:

  IRQ handler type mismatch for IRQ 74
  current handler: serial idle
  ...

and the reason is that setting IRQF_ONESHOT will now result in those
interrupt handlers having different IRQF flags, and thus being
unsharable.  So the commit log in the reverted commit:

                            "Since it is required for those users and
    there is no difference for others it makes sense to add this flag
    unconditionally."

is simply not true: there may not be any difference from a "actions at
irq time", but there is a *big* difference wrt this flag testing irq
management (see __setup_irq() in kernel/irq/manage.c).

One solution may be to stop verifying IRQF_ONESHOT in __setup_irq(), but
right now the safe course of action is to revert the change.  Let's
revisit this in a later merge window.
Reported-by: NPaul Walmsley <paul@pwsan.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Requested-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix kernel-doc warning in irqdesc.c:

  Warning(kernel/irq/irqdesc.c:353): No description found for parameter 'owner'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Function genpd_queue_power_off_work() is not defined for
CONFIG_PM_RUNTIME, so pm_genpd_poweroff_unused() causes a build
error to happen in that case.  Fix the problem by making
pm_genpd_poweroff_unused() depend on CONFIG_PM_RUNTIME too.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Use the move from Linux 2.6 to Linux 3.x as an excuse to kill the
annoying subdirectories in the XFS source code.  Besides the large
amount of file rename the only changes are to the Makefile, a few
files including headers with the subdirectory prefix, and the binary
sysctl compat code that includes a header under fs/xfs/ from
kernel/.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NAlex Elder <aelder@sgi.com>

The patch http://lkml.org/lkml/2003/7/13/226 introduced an RLIMIT_NPROC
check in set_user() to check for NPROC exceeding via setuid() and
similar functions.

Before the check there was a possibility to greatly exceed the allowed
number of processes by an unprivileged user if the program relied on
rlimit only.  But the check created new security threat: many poorly
written programs simply don't check setuid() return code and believe it
cannot fail if executed with root privileges.  So, the check is removed
in this patch because of too often privilege escalations related to
buggy programs.

The NPROC can still be enforced in the common code flow of daemons
spawning user processes.  Most of daemons do fork()+setuid()+execve().
The check introduced in execve() (1) enforces the same limit as in
setuid() and (2) doesn't create similar security issues.

Neil Brown suggested to track what specific process has exceeded the
limit by setting PF_NPROC_EXCEEDED process flag.  With the change only
this process would fail on execve(), and other processes' execve()
behaviour is not changed.

Solar Designer suggested to re-check whether NPROC limit is still
exceeded at the moment of execve().  If the process was sleeping for
days between set*uid() and execve(), and the NPROC counter step down
under the limit, the defered execve() failure because NPROC limit was
exceeded days ago would be unexpected.  If the limit is not exceeded
anymore, we clear the flag on successful calls to execve() and fork().

The flag is also cleared on successful calls to set_user() as the limit
was exceeded for the previous user, not the current one.

Similar check was introduced in -ow patches (without the process flag).

v3 - clear PF_NPROC_EXCEEDED on successful calls to set_user().
Reviewed-by: NJames Morris <jmorris@namei.org>
Signed-off-by: NVasiliy Kulikov <segoon@openwall.com>
Acked-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add FLUSH/FUA support to blktrace. As FLUSH precedes WRITE and/or
FUA follows WRITE, use the same 'F' flag for both cases and
distinguish them by their (relative) position. The end results
look like (other flags might be shown also):

 - WRITE:            W
 - WRITE_FLUSH:      FW
 - WRITE_FUA:        WF
 - WRITE_FLUSH_FUA:  FWF

Note that we reuse TC_BARRIER due to lack of bit space of act_mask
so that the older versions of blktrace tools will report flush
requests as barriers from now on.

Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Reviewed-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Its possible to jam up the alarm timers by setting very small interval
timers, which will cause the alarmtimer subsystem to spend all of its time
firing and restarting timers. This can effectivly lock up a box.

A deeper fix is needed, closely mimicking the hrtimer code, but for now
just cap the interval to 100us to avoid userland hanging the system.

CC: Thomas Gleixner <tglx@linutronix.de>
CC: stable@kernel.org
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>