Add support for multiple hardware receive queues. The ingress traffic is hashed into one of the receive queues based on IP or TCP or both headers. The max no. of receive queues supported is 8.
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid Wang <dwang2@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removed code that is unused
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid Wang <dwang2@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) Update copyright
2) Fix hardware queue descriptor field size CQ_ENET_RQ_DESC_FCOE_SOF_BITS
3) Include rtnetlink.h instead of if_link.h
4) Selectively flush writes to interrupt mask register
5) Use pci_enable_device_mem
6) Remove unused variables and header files
7) Fix size mismatch between memory alloc and free operations of a variable
8) Check for non null arguments to vic_provinfo_alloc
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware has the loopback capability to queue the packets transmitted from
a device to the receive queue of the same device. enic now supports the
loopback capability.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add wrapper routines that issue devcmds to firmware and ensure that a
devcmd lock is held for each devcmd call.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add enic ndo_{set|get}_vf_port ops to support setting/getting
port-profile for enic dynamic devices.  Enic dynamic devices are just like
normal enic eth devices except dynamic enics require an extra configuration
step to assign a port-profile identifier to the interface before the
interface is useable.  Once a port-profile is assigned, link comes up on the
interface and is ready for I/O.  The port-profile is used to configure the
network port assigned to the interface.  The network port configuration
includes VLAN membership, QoS policies, and port security settings typical
of a data center network.

A dynamic enic initially has a zero-mac address.  Before a port-profile is
assigned, a valid non-zero unicast mac address should be assign to the
dynamic enic interface.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>

Provision for multiple Rx/Tx queues.  Max of 8 WQs and 8 RQs.  Max for
completion queue is 8+8=16 and max for interrupt resources is 8+8+2.

Add driver/firmware interface for setting up RSS secret key and indirection
table.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>