Originally, I expected that there would be needed to call update
operation in case RALUE record action is changed. However, that is not
needed since write operation takes care of that nicely. Remove prepared
construct and always call the write operation.

Fixes: 61c503f9 ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In mlxsw we squash tables 254 and 255 together into HW. Kernel adds/dels
/32 ip to/from both 254 and 255. On del path, that causes the same
prefix being removed twice. Fix this by introducing reference counting
for private mlxsw fib entries. That required a bit of code reshuffle.
Also put dev into fib entry key so the same prefix could be represented
once per every router interface.

Fixes: 61c503f9 ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch takes care of clearing the uninitialized buffer before using it.
1. pfc pri-enable bitmap need to be cleared before setting the requested
   enable bits. Without this, the un-touched values will be merged with
   requested values and sent to MFW.
2. The data in app-entry field need to be cleared before using it.
3. Clear the output data buffer used in qed_dcbx_query_params().
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Management firmware requires the selection-field (SF) to be set for
configuring the application/protocol entry in IEEE mode. Without this
setting, the app entry will be configured incorrectly in MFW.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dcbx configuration is not supported for VF interfaces. Hence don't populate
the callbacks for VFs and also fail the dcbx-query for VFs.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return -ENODEV if the MDIO bus is disabled in the device tree.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Acked-by: NJohn Crispin <john@phrozen.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

a lot of parts in the driver uses devm_* APIs to gain benefits from the
device resource management, so devm_mdiobus_alloc is also used instead
of mdiobus_alloc to have more elegant code flow.

Using common code provided by the devm_* helps to
1) have simplified the code flow as [1] says
2) decrease the risk of incorrect error handling by human
3) only a few drivers used it since it was proposed on linux 3.16,
so just hope to promote for this.

Ref:
[1] https://patchwork.ozlabs.org/patch/344093/Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the missing of_node_put() after finishing the usage
of of_get_child_by_name.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Acked-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mtk_stop() must be called to stop for freeing DMA
resources acquired and restoring state changed by mtk_open()
firstly when module removal.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

original mdio_cleanup is not in the symmetric place against where
mdio_init is, so relocate mdio_cleanup to the right one.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Acked-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

these irqs are not used for shared irq and disabled during ethernet stops.
irq requested by devm_request_irq is safe to be freed automatically on
driver detach.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Acked-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use skb_free_frag() instead of legacy put_page()
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Acked-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) If the return value of devm_clk_get is EPROBE_DEFER, we should
defer probing the driver. The change is verified and works based
on 4.8-rc1 staying with the latest clk-next code for MT7623.
2) Changing with the usage of loops to work out if all clocks
required are fine
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

which net device the SKB is complete for depends on the forward port
on txd4 on the corresponding TX descriptor, but the information isn't
set up well in case of  SKB fragments that would lead to watchdog timeout
from the upper layer, so fix it up.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Acked-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Attribute array it87_attributes_in lacks its NULL terminator,
causing random behavior when operating on the attribute group.

Fixes: 52929715 ("hwmon: (it87) Use is_visible for voltage sensors")
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

The Kconfig entry controlling compilation of this code is:

drivers/platform/x86/Kconfig:config GPIO_INTEL_PMIC
drivers/platform/x86/Kconfig:   bool "Intel PMIC GPIO support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

We delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

We don't replace module.h with init.h since the file already has that.

Cc: Alek Du <alek.du@intel.com>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

The Kconfig entry controlling compilation of this code is:

arch/x86/Kconfig:config OLPC
arch/x86/Kconfig:       bool "One Laptop Per Child support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

We delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit b70661c7 ("net: smc91x: use run-time configuration on all ARM
machines") broke some ARM platforms through several mistakes.  Firstly,
the access size must correspond to the following rule:

(a) at least one of 16-bit or 8-bit access size must be supported
(b) 32-bit accesses are optional, and may be enabled in addition to
    the above.

Secondly, it provides no emulation of 16-bit accesses, instead blindly
making 16-bit accesses even when the platform specifies that only 8-bit
is supported.

Reorganise smc91x.h so we can make use of the existing 16-bit access
emulation already provided - if 16-bit accesses are supported, use
16-bit accesses directly, otherwise if 8-bit accesses are supported,
use the provided 16-bit access emulation.  If neither, BUG().  This
exactly reflects the driver behaviour prior to the commit being fixed.

Since the conversion incorrectly cut down the available access sizes on
several platforms, we also need to go through every platform and fix up
the overly-restrictive access size: Arnd assumed that if a platform can
perform 32-bit, 16-bit and 8-bit accesses, then only a 32-bit access
size needed to be specified - not so, all available access sizes must
be specified.

This likely fixes some performance regressions in doing this: if a
platform does not support 8-bit accesses, 8-bit accesses have been
emulated by performing a 16-bit read-modify-write access.

Tested on the Intel Assabet/Neponset platform, which supports only 8-bit
accesses, which was broken by the original commit.

Fixes: b70661c7 ("net: smc91x: use run-time configuration on all ARM machines")
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethtool has 11 flow tables, each flow table has its own priority.
Increase the number of priorities to be aligned with the number of flow
tables.

Fixes: 1174fce8 ('net/mlx5e: Support l3/l4 flow type specs in ethtool flow steering')
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon set ETS failure due to user invalid input, add error prints to
specify the exact error to the user.

Fixes: cdcf1121 ('net/mlx5e: Validate BW weight values of ETS')
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Free 'in' command object also when mlx5_core_modify_tir fails.

Fixes: 724b2aa1 ("net/mlx5e: TIRs management refactoring")
Signed-off-by: NKamal Heib <kamalh@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a counter in ethtool for the number of times that
TX xmit_more was used.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver RQ has two possible configurations: striding RQ and
non-striding RQ.  Until this patch, the driver always reported the
number of hardware WQEs (ring descriptors). For non striding RQ
configuration, this was OK since we have one WQE per pending packet
For striding RQ, multiple packets can fit into one WQE. For better
user experience we normalize the rx_pending parameter (size of wqe/mtu)
as the average ring size in case of striding RQ.

Fixes: 461017cb ('net/mlx5e: Support RX multi-packet WQE ...')
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of asking the firmware to flush the SQ (Send Queue) via
asynchronous completions when moved to error, we handle SQ flush
manually (mlx5e_free_tx_descs) same as we did when SQ flush got
timed out or on tx_timeout.

This will reduce SQs flush time and speedup interface down procedure.

Moved mlx5e_free_tx_descs to the end of en_tx.c for tx
critical code locality.

Fixes: 29429f33 ('net/mlx5e: Timeout if SQ doesn't flush during close')
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ICO (Internal control operations) SQ (Send Queue) is closed/disabled
after RQ (Receive Queue).  After RQ is closed an ICO SQ completion
might post a fragmented MPWQE (Multi Packet Work Queue Element) into
that RQ.

As on regular RQ post, check if we are allowed to post to that
RQ (RQ is enabled). Cleanup in-progress UMR MPWQE on mlx5e_free_rx_descs
if needed.

Fixes: bc77b240 ('net/mlx5e: Add fragmented memory support for RX multi packet WQE')
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will significantly reduce receive queue flush time on interface
down.

Instead of asking the firmware to flush the RQ (Receive Queue) via
asynchronous completions when moved to error, we handle RQ flush
manually (mlx5e_free_rx_descs) same as we did when RQ flush got timed
out.

This will reduce RQs flush time and speedup interface down procedure
(ifconfig down) from 6 sec to 0.3 sec on a 48 cores system.

Moved mlx5e_free_rx_descs en_main.c where it is needed, to keep en_rx.c
free form non critical data path code for better code locality.

Fixes: 6cd392a0 ('net/mlx5e: Handle RQ flush in error cases')
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ConnectX-4 UMR (User Memory Region) MTT translation table offset in WQE
is limited to U16_MAX, before this patch we ignored that limitation and
requested the maximum possible UMR translation length that the netdev
might need (MAX channels * MAX pages per channel).
In case of a system with #cores > 32 and when linear WQE allocation fails,
falling back to using UMR WQEs will cause the RQ (Receive Queue) to get
stuck.

Here we limit UMR length to min(U16_MAX, max required pages) (while
considering the required alignments) on driver load, by default U16_MAX is
sufficient since the default RX rings value guarantees that we are in
range, dynamically (on set_ringparam/set_channels) we will check if the
new required UMR length (num mtts) is still in range, if not, fail the
request.

Fixes: bc77b240 ('net/mlx5e: Add fragmented memory support for RX multi packet WQE')
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to assigning the 'replaced' value instead of or'ing it,
if drm_atomic_crtc_set_property() gets called multiple times,
the last call will define the color_mgmt_changed flag, so
a non-updating call to a property can reset the flag and
prevent actual hw state updates required by preceding
property updates.
Signed-off-by: NMario Kleiner <mario.kleiner.de@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: <stable@vger.kernel.org> # v4.6+
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

On 32-bit systems, mask is only an array of 3 longs, not 4, so don't try
to write to mask[3].
Also include build-time checks in case the size of the bitmask changes.

Fixes: 3c36a2ad ("sfc: display vadaptor statistics for all interfaces")
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The data offset for a dax region needs to account for a reservation in
the resource range.  Otherwise, device-dax is allowing mappings directly
into the memmap or device-info-block area with crash signatures like the
following:

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
 IP: get_zone_device_page+0x11/0x30
 Call Trace:
   follow_devmap_pmd+0x298/0x2c0
   follow_page_mask+0x275/0x530
   __get_user_pages+0xe3/0x750
   __gfn_to_pfn_memslot+0x1b2/0x450 [kvm]
   tdp_page_fault+0x130/0x280 [kvm]
   kvm_mmu_page_fault+0x5f/0xf0 [kvm]
   handle_ept_violation+0x94/0x180 [kvm_intel]
   vmx_handle_exit+0x1d3/0x1440 [kvm_intel]
   kvm_arch_vcpu_ioctl_run+0x81d/0x16a0 [kvm]
   kvm_vcpu_ioctl+0x33c/0x620 [kvm]
   do_vfs_ioctl+0xa2/0x5d0
   SyS_ioctl+0x79/0x90
   entry_SYSCALL_64_fastpath+0x1a/0xa4

Fixes: ab68f262 ("/dev/dax, pmem: direct access to persistent memory")
Link: http://lkml.kernel.org/r/147205536732.1606.8994275381938837346.stgit@dwillia2-desk3.amr.corp.intel.comSigned-off-by: NDan Williams <dan.j.williams@intel.com>
Reported-by: NAbhilash Kumar Mulumudi <m.abhilash-kumar@hpe.com>
Reported-by: NToshi Kani <toshi.kani@hpe.com>
Tested-by: NToshi Kani <toshi.kani@hpe.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When team is in bridge and LACP is utilized, LACPDU packets are pushed
to userspace using raw socket and there they are processed. However,
since 8626c56c, LACPDU skbs are dropped by bridge rx_handler so
they never reach packet handlers in rx path. Fix this by explicity treat
LACPDUs to be pushed to exact delivery in team rx_handler.
Reported-by: NIdo Schimmel <idosch@mellanox.com>
Fixes: 8626c56c ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ppe_cb->ppe_common_cb is being dereferenced before a null check is
being made on it.  If ppe_cb->ppe_common_cb is null then we end up
with a null pointer dereference when assigning dsaf_dev.  Fix this
by moving the initialisation of dsaf_dev once we know
ppe_cb->ppe_common_cb is OK to dereference.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NYisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bootloader (U-boot) sometimes uses this timer for various delays.
It uses it as a ongoing counter, and does comparisons on the current
counter value. The timer counter is never stopped.

In some cases when the user interacts with the bootloader, or lets
it idle for some time before loading Linux, the timer may expire,
and an interrupt will be pending. This results in an unexpected
interrupt when the timer interrupt is enabled by the kernel, at
which point the event_handler isn't set yet. This results in a NULL
pointer dereference exception, panic, and no way to reboot.

Clear any pending interrupts after we stop the timer in the probe
function to avoid this.

Cc: stable@vger.kernel.org
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Driver init code incorrectly uses the block base address and as a result
clears clocksource structure's fields instead of the hardware registers.

Commit 09a99820 ("timekeeping: Lift clocksource cacheline
restriction") has changed the offsets within pistachio_clocksource
structure and what has previously gone unnoticed now leads to a kernel
panic during boot.
Signed-off-by: NMarcin Nowakowski <marcin.nowakowski@imgtec.com>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

mck is needed to get the PIT working. Explicitly prepare_enable it instead
of assuming it is enabled.

This solves an issue where the system is freezing when the ETM/ETB drivers
are enabled.
Reported-by: NOlivier Schonken <olivier.schonken@gmail.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

When cp_rx_poll does not get enough packet, it will check the rx
interrupt status again. If so, it will jumpt to rx_status_loop again.
But the goto jump resets the rx variable as zero too.

As a result, it causes one possible deadloop. Assume this case,
rx_status_loop only gets the packet count which is less than budget,
and (cpr16(IntrStatus) & cp_rx_intr_mask) condition is always true.
It causes the deadloop happens and system is blocked.
Signed-off-by: NGao Feng <fgao@ikuai8.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes a common flow for Client instance open during init
and reset path. The Client subtask can handle both the cases instead of
making a separate notify_client_of_open call.
Also it may fix a bug during reset where the service task was leaking
some memory and causing issues.

Change-Id: I7232a32fd52b82e863abb54266fa83122f80a0cd
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts:
  commit 33c133cc ("phy: IRQ cannot be shared")

On hardware with multiple PHY devices hooked up to the same IRQ line, allow
them to share it.

Sergei Shtylyov says:
  "I'm not sure now what was the reason I concluded that the IRQ sharing
  was impossible... most probably I thought that the kernel IRQ handling
  code exited the loop over the IRQ actions once IRQ_HANDLED was returned
  -- which is obviously not so in reality..."
Signed-off-by: NXander Huff <xander.huff@ni.com>
Signed-off-by: NNathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We kept shadow copies of which interrupt sources we have enabled and
disabled, but due to an order bug in how intrl2_mask_clear was defined,
we could run into the following scenario:

CPU0					CPU1
intrl2_1_mask_clear(..)
sets INTRL2_CPU_MASK_CLEAR
					bcm_sf2_switch_1_isr
					read INTRL2_CPU_STATUS and masks with stale
					irq1_mask value
updates irq1_mask value

Which would make us loop again and again trying to process and interrupt
we are not clearing since our copy of whether it was enabled before
still indicates it was not. Fix this by updating the shadow copy first,
and then unasking at the HW level.

Fixes: 246d7f77 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>