RealView boards like PB11MPCore have 512MB of RAM available contiguously
at 0x70000000. Half of the memory is mirrored at 0x00000000 for
backwards compatibility. This patch adds the
CONFIG_REALVIEW_HIGH_PHYS_OFFSET option option to change the physical
base address so that the full amount of RAM is available to Linux. Note
that the EB board has 256MB of RAM also mirrored at 0x70000000, the only
board without this feature being PB1176.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Since boards like PB11MPCore have 512MB of RAM and 128MB of flash, the
virtual space is short on vmalloc memory and mapping the flash fails.
This patch changes the IO_ADDRESS so that static mappings start at
0xfc000000 and moves the PCI virtual addresses higher up. The new
VMALLOC_END is set to 0xf8000000 (512MB higher than the old value).
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The UART0 address is different on PB1176 from EB or PB11MPCore. This
patch adds the necessary #ifdef's to this file. The disadvantage is
that enabling CONFIG_DEBUG_LL will work properly on PB1176 if only
this platform is enabled.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch adds another clcd_panel structure for the above resolution
and makes it the default for the PB1176 and PB11MPCore platforms.
Signed-off-by: NColin Tuckley <Colin.Tuckley@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

On PB1176, oscillator 0 rather than 4 should be used.
Signed-off-by: NColin Tuckley <colin.tuckley@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch annotates the platform_secondary_init function in
arch/arm/mach-realview/platsmp.c with trace_hardirqs_off to avoid a
warning when LOCKDEP and TRACE_IRQFLAGS are enabled.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch annotates the platform_secondary_init function in
arch/arm/mach-realview/platsmp.c with trace_hardirqs_off to avoid a
warning when LOCKDEP and TRACE_IRQFLAGS are enabled.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

None of these files use any of the functionality promised by
asm/semaphore.h.  It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

By default, this option was selected by the platform Kconfig. This
patch adds "depends on" to L2X0 so that it can be enabled/disabled
manually.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch enables the building of Linux for the PB1176 platform.
Signed-off-by: NBahadir Balban <bahadir.balban@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch adds the base files for the PB1176 platform support.
Signed-off-by: NBahadir Balban <bahadir.balban@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch adds the resource and device definitions for the compact
flash.
Signed-off-by: NBahadir Balban <bahadir.balban@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch adds the PB11MPCore support to the corresponding Kconfig
and Makefile to enable building.
Signed-off-by: NBahadir Balban <bahadir.balban@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch adds the initialisation calls for the SMP support on the
PB11MPCore platform.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch adds the base files for the PB11MPCore platform support.
Signed-off-by: NBahadir Balban <bahadir.balban@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The upcoming PB11MPCore and PB1176 have different memory maps and some
of the definitions in platform.h are no longer common. This patch
moves them to the board-eb.h file and updates their usage in
realview_eb.c.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Since the PB1176 has different UART base addresses, this patch moves
the definitions form platorm.h to board-eb.h. It also modifies
uncompress.h to detect the platform type at run-time.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch moves the timer definitions from platform.h into board-eb.h
as they are different on PB11MPCore and PB1176. It also adds
timerX_va_base variables in core.c which are set by the
realview_eb_timer_init function before invoking realview_timer_init.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch moves the patch definitions into board-eb.h and
realview_eb.c (from core.c) as they are different on the PB11MPCore
and PB1176 platforms.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This is in preparation for the RealView PB11MPCore and PB1176 patches
which have different base addresses for the GIC.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

RealView/EB revD platform comes with the SMSC LAN9118 Ethernet
chip. This patch allows either the smc91x or the smc911x drivers to be
used with the RealView/EB platform.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch moves the SCU initialisation from __v6_setup to the
smp_prepare_cpus() function as it relies on platform-specific
settings. Changes to get_core_count() are mainly for allowing cleaner
code with the upcoming PB11MPCore patches.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch changes the REALVIEW_MPCORE configuration option to
REALVIEW_EB_ARM11MP since this is only specific to RealView/EB.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch removes the TWD_BASE macro used to set up and configure the
local timers on ARM11MPCore. The twd_base_addr and twd_size variables
are defined in localtimer.c and set from the realview_eb_init function.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch sets the timer IRQ at run-time by moving the sys_timer
structure and the timer_init function to the realview_eb.c file. This
allows multiple RealView platforms to be compiled in the same kernel
image.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch modifies the get_irqnr_preamble macro to work with multiple
platforms at run-time by reading the address of the GIC controller from
the gic_cpu_base_addr variable. This variable is defined in core.c and
intialised in realview_eb.c (gic_init_irq).
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds the core-tile detection and only enables devices if the
corresponding tile is present. It currently detects the ARM11MPCore via
the core_tile_eb11mp() macro.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch moves the IRQ and DMA definitions from core.h into
realview_eb.c since they are platform-specific. It adds a
realview_eb11mp_fixup function to adjust the IRQ numbers if the
ARM11MPCore tile is fitted. The realview_smc91x_device is also moved
from core.c into realview_eb.c.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch moves the platform specific definitions from platform.h into
the board-eb.h file. It drops the INT_* definitions as they are no
longer used in irqs.h (moved to board-eb.h). It renames REALVIEW_*
macros to REALVIEW_EB_* or REALVIEW_EB11MP_* to distinguish between
standard EB and EB + the ARM11MPCore tile. The platform.h file contains
common definitions to the RealView platforms and it is only directly
included in board-*.h files.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch registers the local timers on ARM11MPCore as clock event
devices. The clock device can be set up as periodic or oneshot.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds dummy local timers for each CPU so that the board clock
device is used to broadcast events to the other CPUs. The patch also
adds the declaration for the dummy_timer_setup function (the equivalent
of local_timer_setup when CONFIG_LOCAL_TIMERS is not set).

Due to the way clockevents work, the dummy timer on the first CPU has to
be registered before the board timer.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The patch updates the RealView code to the clockevents infrastructure.
The SMP support is implemented in subsequent patches. Based on the
Versatile implementation by Kevin Hilman.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The patch updates the RealView platform code to use the generic
clocksource infrastructure for basic time keeping. Based on the
Versatile implementation by Kevin Hilman.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the xtime write mode seqlock into timer_tick(), so it only
surrounds the call to do_timer().

This avoids a deadlock in update_process_times() ...
hrtimer_get_softirq_time() which tries to get a read mode seqlock
on xtime, thereby preventing booting.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The second GIC asserts a permanent interrupt on Rev.B MPCore platforms.
Disable initialisation of this GIC to avoid unbootable systems.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Spelling fixes in arch/arm/.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>