This patch makes the followinf proc entries per-netns:
/proc/net/igmp
/proc/net/mcfilter
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NDaniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: NBenjamin Thery <benjamin.thery@bull.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Looks like everything is already ready.

Required for ebtables(8) for one thing.

Also, required for ipmr per-netns (coming soon). (Benjamin)
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NBenjamin Thery <benjamin.thery@bull.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the module is removed while its interface is up, smsc911x_stop is not
called until after smsc911x_drv_remove has disposed of phy_dev.  This
patch changes the stop method to handle this situation.

This is a different problem to the one reported by dfoley@telus.net.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:

	drivers/net/ppp_generic.c

When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter.  This patch cleans up that api by
properly removing it..
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flag marking a device running must be set before the URBs for
recption are submitted or they may complete too early and fail to resubmit.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While implementing a TCQ_F_THROTTLED flag there was used an smp_wmb()
in qdisc_watchdog(), but since this flag is practically used only in
sch_netem(), and since it's not even clear what reordering is avoided
here (TCQ_F_THROTTLED vs. __QDISC_STATE_SCHED?) it seems the barrier
could be safely removed.
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch bumps the release number of the driver.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch saves the MIER register contents before treating
interrupts, then restores them correcty at the end of the
interrupt routine.
Signed-off-by: NJoe Chou <Joe.Chou@rdc.com.tw>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a reverse logic in the MDIO code.
Signed-off-by: NJoe Chou <Joe.Chou@rdc.com.tw>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A command like this: "brctl addif br1 eth1" issued as a user gave me
an oops when bridge module wasn't loaded. It's caused by using a dev
pointer before checking for NULL.
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the version number to 3.97.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleans up the tg3 header file by removing the preprocessor
definitions for standard PCI configuration space registers.  The driver
should be using the standard definitions when needed.  The patch
continues by removing redundant PHY related definitions and reorganizes
some of the remaining entries.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the pci_bist and pci_hdr_type members from the
device structure and removes the code that references them.  They are
not really used.

The patch rounds out the changes by moving the pci_cmd member to plug
a structure hole that would have been created.  On 32-bit systems, this
movement removes a subsequent structure hole later in the structure. On
64-bit systems though, the movement merely consolidates two holes into
one larger hole.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch attempts to make the relationship between IPV6 checksum
offload and IPV6 LSO more obvious.  The patch also toggles a bit
needed for IPV6 LSO on 5785 and 57780 devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first hunk of this patch inverts a flag that was accidentally
toggled as part of commit 0a459aac
("tg3: Allow WOL for phylib controlled Broadcom phys").

The second hunk of the patch removes the call to
device_may_wakeup() in the 5906 config detection path.  At the
point of the call, the driver shouldn't be querying for WOL
capability.  It should be detecting and setting it.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some gcc versions warn that ret may be used uninitialized in
sfq_enqueue(). It's a false positive, so let's annotate this.
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Priority flow contol statistics for Data Center Bridging (DCB) weren't
included in ethtool.  This patch adds them.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NEric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds the Backward Congestion Notification Address (BCNA) attribute to the
Backward Congestion Notification (BCN) interface for Data Center Bridging
(DCB), which was missing.  Receive the BCNA attribute in the ixgbe driver.
The BCNA attribute is for a switch to inform the endstation about the physical
port identification in order to support BCN on aggregated links.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NEric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Data Center Bridging (DCB) had no way to know if setstate had failed in the
driver.  This patch enables dcb netlink code to handle the status for the DCB
setstate interface.  Likewise it allows the driver to return a failed status
if MSI-X isn't enabled.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NEric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds an option to dump all crypto related memory to
the kernel log.
Obviously, it should not be enabled on productive systems. ;)
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We should suspend the MAC, before we kill the radio. This gives
the MAC a chance to leave any TX/RX state and it avoids races on
the PHY/RADIO registers.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Packet length calculation (which includes frame check sequence)
should take into account whether we add a pad field or not.
Extract the calculation into a helper and use it in both places.

Changes to desc.c
Changes-licensed-under: ISC

Changes to ath5k.h, base.c
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch implements dynamic power save for mac80211. Basically it
means enabling power save mode after an idle period. Implementing it
dynamically gives a good compromise of low power consumption and low
latency. Some hardware have support for this in firmware, but some
require the host to do it.

The dynamic power save is implemented by adding an timeout to
ieee80211_subif_start_xmit(). The timeout can be enabled from userspace
with Wireless Extensions. For example, the command below enables the
dynamic power save and sets the time timeout to 500 ms:

iwconfig wlan0 power timeout 500m

Power save now only works with devices which handle power save in firmware.
It's also disabled by default and the heuristics when and how to enable is
considered as a policy decision and will be left for the userspace to handle.
In case the firmware has support for this, drivers can disable this feature
with IEEE80211_HW_NO_STACK_DYNAMIC_PS.

Big thanks to Johannes Berg for the help with the design and code.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a preparation for the dynamic power save support. In future there are
two paths to stop the master queues and we need to track this properly to
avoid starting queues incorrectly. Implement this by adding a status
array for each queue.

The original idea and design is from Johannes Berg, I just did
the implementation based on his notes. All the bugs are mine, of course.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also disable power save when disassociated. It makes no sense to have
power save enabled while disassociated.

iwlwifi seems to have this check in the driver, but it's better to do this
in mac80211 instead.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes some locking w.r.t. the lower MAC (firmware).
It also removes a lot of ancient IRQ-locking that's not needed anymore.
We simply suspend the MAC. That's easier and causes less trouble.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes unused parameter and unused local variable in
methods in iwl-tx.c:

- Remove a parameter (is_unicast) from iwl_tx_cmd_build_basic().

- Remove an unused variable name unicast from iwl_tx_skb().
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The RX code in ath9k uses sc_keymap to figure out whether a default
key was used. However, the default key entries in sc_keymap were
always set and as such, frames could have been claimed to be decrypted
by hardware when they were not. This can cause problems especially
with TKIP since mac80211 is validating the Michael MIC in the frame
and this will result in MIC failure and potentially TKIP
countermeasures if the frame was not decrypted correctly.

Change key cache slot allocation to mark only the keys that really
have been used in sc_keymap to avoid the issue. The key cache slot
selection routines are now internally avoiding the slots that may be
needed for TKIP group keys.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath_reserve_key_cache_slot() was obviously supposed to return an index
to a free slot, not reserved one. This could have caused problems with
hardware revisions that use splitmic.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This should fix the timeout issues seen when using wpa_supplicant.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In stress testing p54usb, the WARN_ON() in ieee80211_tasklet_handler() was
triggered; however, there is no logging of the received value for packet
type. Adding that feature will improve the warning.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a serious regression (introduced by:
"p54: fix memory management")
that affected isl3886+net2280 usb devices operation.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Tested-by: NArtur Skawina <art.08.09@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enhance allocation of key cache entries to support multiple pairwise
keys to fix AP mode with more than one associated STA.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It looks like mac80211 may try to send unicast frames to a STA that
does not have a STA entry. We need to make sure that that is caught in
the rate control code before dereferencing STA data.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch checks if the radio is disabled before displaying the tx power
level. Previously when the txpower was set off show_tx_power still
returned the prior power level. Now it will indicate the power has been
turned off.
Signed-off-by: NJay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously we allocate Rx SKB with GFP_ATOMIC flag. This is because we need
to hold a spinlock to protect the two rx_used and rx_free lists operation
in the rxq.

	spin_lock();
	...
	element = rxq->rx_used.next;
	element->skb = alloc_skb(..., GFP_ATOMIC);
	list_del(element);
	list_add_tail(&element->list, &rxq->rx_free);
	...
	spin_unlock();

After spliting the rx_used delete and rx_free insert into two operations,
we don't require the skb allocation in an atomic context any more (the
function itself is scheduled in a workqueue).

	spin_lock();
	...
	element = rxq->rx_used.next;
	list_del(element);
	...
	spin_unlock();
	...
	element->skb = alloc_skb(..., GFP_KERNEL);
	...
	spin_lock()
	...
	list_add_tail(&element->list, &rxq->rx_free);
	...
	spin_unlock();

This patch should fix the "iwlagn: Can not allocate SKB buffers" warning
we see recently.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>