This fixes a netstamp_needed accounting issue when the listen socket
has SO_TIMESTAMP set:

    s = socket(AF_INET, SOCK_STREAM, 0);
    setsockopt(s, SOL_SOCKET, SO_TIMESTAMP, 1); -> netstamp_needed = 1
    bind(s, ...);
    listen(s, ...);
    s2 = accept(s, ...); -> netstamp_needed = 1
    close(s2); -> netstamp_needed = 0
    close(s); -> netstamp_needed = -1
Signed-off-by: NOctavian Purdila <opurdila@ixiacom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the driver probe function the emac module clock needs to
be enabled before calling register_netdev(). As soon as the
device is registered the driver get_stats function can be invoked
by the core - the module clock must be switched on to be able to
read from stats registers. Also explicitly call matching clk_disable
for failure conditions in probe function.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Davicom DM9100 and DM9102 chips are used on the motherboards of
some SPARC systems (supported by the tulip driver) and also in PCI
expansion cards (supported by the dmfe driver).  There is no
difference in the PCI device ids for the two different configurations,
so these drivers both claim the device ids.  However, it is possible
to distinguish the two configurations by the presence of Open Firmware
properties for them, so we do that.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tc is still throwing a warning that is could be used
uninitialized.  This fixes it, and properly formats the device ID
checks for the use of this variable.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If NET_SKB_PAD is not a multiple of the cache line size, mv643xx_eth
allocates a couple of extra bytes at the start of each receive buffer
to make the data payload end up on a cache line boundary.

These extra bytes are skb_reserve()'d before DMA mapping, so they
should not be included in the DMA map byte count (as the mapping is
done starting at skb->data), nor should they be included in the
receive descriptor buffer size field, or the hardware can end up
DMAing beyond the end of the buffer, which can happen if someone
sends us a larger-than-MTU sized packet.

This problem was introduced in commit 7fd96ce4 ("mv643xx_eth:
rework receive skb cache alignment", May 6 2009), but hasn't appeared
to be problematic so far, probably as the main users of mv643xx_eth
all have NET_SKB_PAD == L1_CACHE_BYTES.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stanse found a memory leak in atl2_get_eeprom. eeprom_buff is not
freed/assigned on all paths. Fix that.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: atl1-devel@lists.sourceforge.net
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A failure on request_irq() is always fatal but unlike other fatal
errors it's only reported to the user if net_debug is set. Make the
diagnostic unconditional and raise the priority so that errors are
more obvious to the user.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed missing newlines in calls to dev_warn & dev_err.
Signed-off-by: NJan Dumon <j.dumon@option.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't send flow control settings to any port other than the modem port.
Older firmware ignored this request but did sent a reply. Newer firmware just
ignores it without reply and causes a 5 second timeout every time a port
(except for the modem port) is opened or if tiocm settings are changed.
Signed-off-by: NJan Dumon <j.dumon@option.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Attempt to reset the usb device when we receive usb bus errors.
Signed-off-by: NJan Dumon <j.dumon@option.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't change the state of a port if it's not open. This fixes an issue where a
port sometimes has to be opened twice before data can be received.
Signed-off-by: NJan Dumon <j.dumon@option.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some fields are always little endian and have to be converted on big endian
machines.
Signed-off-by: NJan Dumon <j.dumon@option.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add product ID's for new devices.
Signed-off-by: NJan Dumon <j.dumon@option.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Claw module cannot be loaded together with qeth, because "qeth" has
been errorneously used as root device name. It is changed into "claw".
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pcnet_cs,serial_cs:

add cis of KTI PE520 pcmcia network card,
and serial card(Sierra Wireless AC860).
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we have L3 tunnels with different inner/outer families
(i.e. IPV4/IPV6) which use a multicast address as the outer tunnel
destination address, multicast packets will be loopbacked back to the
sending socket even if IP*_MULTICAST_LOOP is set to disabled.

The mc_loop flag is present in the family specific part of the socket
(e.g. the IPv4 or IPv4 specific part).  setsockopt sets the inner
family mc_loop flag. When the packet is pushed through the L3 tunnel
it will eventually be processed by the outer family which if different
will check the flag in a different part of the socket then it was set.
Signed-off-by: NOctavian Purdila <opurdila@ixiacom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

current the Rx/Tx FIFO size settings cause problem
when four UEC ethernets work simultaneously.

eg: GETH1, UEM-J15, GETH2, UEC-J5 on 8569MDS board

 $ ifconfig eth0 10.193.20.166
 $ ifconfig eth1 10.193.20.167
 $ ifconfig eth2 10.193.20.168
 then
 $ ifconfig eth3 10.193.20.169

The fourth ethernet will cause all of interface broken,
you cann't ping successfully any more.
The patch fix this issue for MPC8569 Rev1.0 and Rev2.0
Signed-off-by: NDave Liu <daveliu@freescale.com>
Acked-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noticed by Stephen Rothwell.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Fix ethtool link test for NX3031 chip.
o Remove unused code from phy interrupt callback
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Dump registers such as tx ring and rx ring counter, firmware state,
  niu regs, etc. which can be useful for debugging purpose.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tx_skbuff is define as:
        struct sk_buff          *tx_skbuff[TX_RING_ENTRIES];

EVT_RING_ENTRIES is 64 and TX_RING_ENTRIES is 32.

This function is in a error path so that's why it wasn't noticed.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This always evaluates to true.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If no break occurred, cnt reaches 0 after the loop.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With `while (--limit > 0)' i reaches 0 after the loop, so upon timeout the
error was not returned.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With `while (--i > 0)' i reaches 0 after the loop, so upon timeout the
error was not issued.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

lp->rx_skb has type struct sk_buff **, not struct sk_buff *, so the
elements of the array should have pointer type, not structure type.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@disable sizeof_type_expr@
type T;
T **x;
@@

  x =
  <+...sizeof(
- T
+ *x
  )...+>
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a target login issue, when parent interface is vlan and we are using cxgb3i sepecific
private ip address in '/etc/iscsi/ifaces/' iface file.
Acked-by: NKaren Xie <kxie@chelsio.com>
Signed-off-by: NRakesh Ranjan <rakesh@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This should address the problems in version 1 (lazy) and version 2 (ugly).

Bump the stats on orig_dev not on the newly assigned NULL dev variable.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With `while (i++ < MII_TIMEOUT)' i reaches MII_TIMEOUT + 1 after the loop
This is probably unlikely a problem in practice.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test the just-allocated value for NULL rather than some other value.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression x,y;
statement S;
@@

x = \(kmalloc\|kcalloc\|kzalloc\)(...);
(
if ((x) == NULL) S
|
if (
-   y
+   x
       == NULL)
 S
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NOliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code checked slot_rx twice.  Check slot_tx by analogy with the bank
case.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression E;
@@

(
*E && E
|
*E || E
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net/sctp/socket.c: In function 'sctp_setsockopt_autoclose':
net/sctp/socket.c:2090: warning: comparison is always false due to limited range of data type

Cc: Andrei Pelinescu-Onciul <andrei@iptel.org>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cat /proc/net/rose displayed a rose sockets abnormal lci value, i.e.
greater than maximum number of VCs per neighbour allowed.
This number prevents further test of lci value during rose operations.

Example (lines shortened) :
[bernard]# cat /proc/net/rose
dest_addr  dest_call src_addr   src_call  dev   lci neigh st vs vr va
*          *         2080175520 F6BVP-1   rose0 000 00000  0  0  0  0
2080175520 FPAD-0    2080175520 WP-0      rose0 FFE 00001  3  0  0  0

Here are the default parameters :

linux/include/net/rose.h:#define ROSE_DEFAULT_MAXVC 50 /* Maximum number of VCs per neighbour */
linux/net/rose/af_rose.c:int sysctl_rose_maximum_vcs = ROSE_DEFAULT_MAXVC;

With the following patch, rose_loopback_timer() attributes a VC number
within limits.
Signed-off-by: NBernard Pidoux <f6bvp@amsat.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

velocity_open() calls velocity_give_many_rx_descs(), which gives RX
descriptors to the NIC, before installing an interrupt handler or
calling velocity_init_registers().  I think this is very unsafe and it
appears to explain the bug report <http://bugs.debian.org/508527>.

On MTU change, velocity_give_many_rx_descs() is again called before
velocity_init_registers().  I'm not sure whether this is unsafe but
it does look wrong.

Therefore, move the calls to velocity_give_many_rx_descs() after
request_irq() and velocity_init_registers().
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Tested-by: NJan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We use a rather complicated logic to support eTSEC and eTSEC2.0
registers maps in a single driver. Currently, the code tries to
unmap 'regs', but for non-eTSEC2.0 controllers 'regs' doesn't
point to a mapping start, and this might cause badness on probe
failure or module removal:

 Freescale PowerQUICC MII Bus: probed
 Trying to vfree() nonexistent vm area (e107f000)
 ------------[ cut here ]------------
 Badness at c00a7754 [verbose debug info unavailable]
 NIP: c00a7754 LR: c00a7754 CTR: c02231ec
 [...]
 NIP [c00a7754] __vunmap+0xec/0xf4
 LR [c00a7754] __vunmap+0xec/0xf4
 Call Trace:
 [df827e50] [c00a7754] __vunmap+0xec/0xf4 (unreliable)
 [df827e70] [c001519c] iounmap+0x44/0x54
 [df827e80] [c028b924] fsl_pq_mdio_probe+0x1cc/0x2fc
 [df827eb0] [c02fb9b4] of_platform_device_probe+0x5c/0x84
 [df827ed0] [c0229928] really_probe+0x78/0x1a8
 [df827ef0] [c0229b20] __driver_attach+0xa4/0xa8

Fix this by introducing a proper priv structure (finally!), which
now holds 'regs' and 'map' fields separately.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sometimes ucc_geth fails to suspend with the following trace:

 ucc_geth e0103000.ucc: suspend
 ucc_geth e0102000.ucc: suspend
 NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out
 ------------[ cut here ]------------
 Badness at net/sched/sch_generic.c:255
 NIP: c021cb5c LR: c021cb5c CTR: c01ab4b4
 [...]
 NIP [c021cb5c] dev_watchdog+0x298/0x2a8
 LR [c021cb5c] dev_watchdog+0x298/0x2a8
 Call Trace:
 [c0389da0] [c021cb5c] dev_watchdog+0x298/0x2a8 (unreliable)
 [c0389e00] [c0031ed8] run_timer_softirq+0x16c/0x1dc
 [c0389e50] [c002c638] __do_softirq+0xa4/0x11c
 [...]

This patch fixes the issue by properly detaching the device on
suspend, and attaching it back on resume.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since hibernation assumes power loss, we should fully reinitialize
PHYs (including platform fixups), as if PHYs were just attached.

This patch factors phy_init_hw() out of phy_attach_direct(), then
converts mdio_bus to dev_pm_ops and adds an appropriate restore()
callback.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sometimes kernel hangs on resume with the following trace:

 ucc_geth e0102000.ucc: resume
 INFO: task bash:1764 blocked for more than 120 seconds.
 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
 bash          D 0fecf43c     0  1764   1763 0x00000000
 Call Trace:
 [cf9a7c10] [c0012868] ret_from_except+0x0/0x14 (unreliable)
 --- Exception: cf9a7ce0 at __switch_to+0x4c/0x6c
     LR = 0xcf9a7cc0
 [cf9a7cd0] [c0008c14] __switch_to+0x4c/0x6c (unreliable)
 [cf9a7ce0] [c028bcfc] schedule+0x158/0x260
 [cf9a7d10] [c028c720] __mutex_lock_slowpath+0x80/0xd8
 [cf9a7d40] [c01cf388] phy_stop+0x20/0x70
 [cf9a7d50] [c01d514c] ugeth_resume+0x6c/0x13c
 [...]

Here is why.

On suspend:

- PM core starts suspending devices, ucc_geth_suspend gets called;

- ucc_geth calls phy_stop() on suspend. Note that phy_stop() is
  mostly asynchronous so it doesn't block ucc_geth's suspend routine,
  it just sets PHY_HALTED state and disables PHY's interrupts;

- Suddenly the state machine gets scheduled, it grabs the phydev->lock
  mutex and tries to process the PHY_HALTED state, so it calls
  phydev->adjust_link(phydev->attached_dev). In ucc_geth case
  adjust_link() calls msleep(), which reschedules the code flow back to
  PM core, which now finishes suspend and so we end up sleeping with
  phydev->lock mutex held.

On resume:

- PM core starts resuming devices (notice that nobody rescheduled
  the state machine yet, so the mutex is still held), the core calls
  ucc_geth's resume routine;

- ucc_geth_resume restarts the PHY with phy_stop()/phy_start()
  sequence, and the phy_*() calls are trying to grab the phydev->lock
  mutex. Here comes the deadlock.

This patch fixes the issue by stopping the state machine on suspend
and starting it again on resume.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>