range_min is the lowest address in the virtual register range. This is
the first register with address 0, not the first register of page 1.

Currently all writes to page 1 are mapped to page 0, so the codec fails
to operate.

Fixes: 4d208ca4 (ASoC: tlv320aic32x4: Convert to direct regmap API usage)
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org (v3.13 if the fix misses -final)

Make it easier for generic code to work with set_sysclk() by distinguishing
between the operation not being supported and an error as is done for
other operations like set_dai_fmt()
Signed-off-by: NMark Brown <broonie@linaro.org>

soc_widget_read API returns the register data and it is possible
that a register can contain 0xffffffff. Thus, change the prototype
of soc_widget_read to return only the error code and pass the reg
data through pointer argument.
Signed-off-by: NArun Shamanna Lakshmi <aruns@nvidia.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The Samsung dmaengine ASoC driver is used with two different dmaengine drivers.
The pl80x, which properly supports residue reporting and the pl330, which
reports that it does not support residue reporting. So there is no need to
manually set the NO_RESIDUE flag. This has the advantage that a proper (race
condition free) PCM pointer() implementation is used when the pl80x driver is
used. Also once the pl330 driver supports residue reporting the ASoC PCM driver
will automatically start using it.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The pl330 driver properly reports that it does not have residue reporting
support, which means the PCM dmanegine driver is able to figure this out on its
own. So there is no need to set the flag manually. Removing the flag has the
advantage that once the pl330 driver gains support for residue reporting it will
automatically be used by the generic dmaengine PCM driver.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The dmaengine framework now exposes the granularity with which it is able to
report the transfer residue for a certain DMA channel. Check the granularity in
the generic dmaengine PCM driver and
	a) Set the SNDRV_PCM_INFO_BATCH if the granularity is per period or worse.
	b) Fallback to the (race condition prone) period counting if the driver does
	not support any residue reporting.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Currently we have two different snd_soc_platform_driver structs in the generic
dmaengine PCM driver. One for dmaengine drivers that support residue reporting
and one for those which do not. When registering the PCM component we check
whether the NO_RESIDUE flag is set or not and use the corresponding
snd_soc_platform_driver. This patch modifies the driver to only have one
snd_soc_platform_driver struct where the pointer() callback checks the
NO_RESIDUE flag at runtime. This allows us to set the NO_RESIDUE flag after the
PCM component has been registered. This becomes necessary when querying whether
the dmaengine driver supports residue reporting from the dmaengine driver itself
since the DMA channel might only be requested after the PCM component has been
registered.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

It's a bug that writing to the platform data directly, for it should
be constant. So just copy it before writing.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Instead of open-coding the intersecting of two rate masks (and getting slightly
wrong for some of the corner cases) use the new snd_pcm_rate_mask_intersect()
helper function.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

SNDRV_PCM_RATE_CONTINUOUS means that all rates (possibly limited to a certain
interval) are supported. There is no need to manually set other rate bits.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NDaniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: NMark Brown <broonie@linaro.org>

SNDRV_PCM_RATE_CONTINUOUS means that all rates (possibly limited to a certain
interval) are supported. There is no need to manually set other rate bits.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

If none of the components (CODEC or CPU DAI) sets a maximum sample rate we'll
end up with the rate_max field of the runtime hardware set to 0.  (Note that it
is still possible for the components to constrain the supported sample rates
using other methods, e.g. setting a list constraint) If rate_max is 0 this means
that the sound card doesn't support any rates at all, which is not the desired
result. So initialize rate_max to UINT_MAX. For symmetry reasons also set
rate_min to 0.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Remove asoc_simple_get_card_info macro and use snd_soc_card_set_drvdata
and snd_soc_card_get_drvdata instead.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This codec driver fails to probe because it has a higher regmap
range_max value than max_register. This patch sets the range_max to the
max_register value as described in the for struct regmap_range_cfg:
"@range_max: Address of the highest register in virtual range."

Fixes: 4d208ca4 (ASoC: tlv320aic32x4: Convert to direct regmap API usage)
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org (v3.13 if the fix misses -final)

Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>

This patch implements a device-tree-only CPU DAI driver for Freescale ESAI
controller that supports:

 - 12 channels playback and 8 channels record.
   [ Some of the inner transmitters and receivers are sharing same group of
     pins. So the maxmium 12 output or 8 input channels are only valid if
     there is no pin conflict occurring to it. ]

 - Independent (asynchronous mode) or shared (synchronous mode) transmit and
   receive sections with separate or shared internal/external clocks and frame
   syncs, operating in Master or Slave mode.
   [ Current ALSA seems not to allow CPU DAI drivers to configure DAI format
     separately for PLAYBACK and CAPTURE. So this first version only supports
     the case that uses the same DAI format for both directions. ]

 - Various DAI formats: I2S, Left-Justified, Right-Justified, DSP-A and DSP-B.

 - Programmable word length (8, 16, 20 or 24bits)

 - Flexible selection between system clock or external oscillator as input
   clock source, programmable internal clock divider and frame sync generation.
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add controls to enable/disable the headphone short circuit protection of
the headphone outputs.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

If the dt is used and the cinfo is NULL, the -ENOMEM should be return.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

If the dt is not used, the cinfo will be always NULL before using it.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

For those platforms using DAI master mode like I2S, it's better to pre-set
a default slot number so that there's no need for these common cases to set
the slot number from its machine driver any more.
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add the missing clk_disable_unprepare() before return from
fsl_ssi_probe() in the request irq error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NMark Brown <broonie@linaro.org>

Some DMA cores might add additional restrictions on which in memory audio
formats can be supported by the compound sound card. If the PCM component
specifies a set of formats it supports (by setting the formats field to non 0)
take these into account when calculating the format set for the compound sound
card.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>

Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>