BugLink: http://bugs.launchpad.net/bugs/696493

According to datasheet (and real-world testing), IDT 92HD88B can
have internal mics at NID 0x11 and 0x20, so enable them accordingly.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the d-mics are assigned to the same purpose of another analog mic
pins, the driver doesn't compute the index properly, resulting in an
error with "existing control".  This patch fixes it.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It sounds like a non-linear beep tone on my test machines...
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

These codecs have the digital beep widget in NID 0x21.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

BugLink: https://launchpad.net/bugs/683695

The original reporter states that headphone jacks do not appear to
work.  Upon inspecting his codec dump, and upon further testing, it is
confirmed that the "alienware" model quirk is correct.

Reported-and-tested-by: Cody Thierauf
Cc: <stable@kernel.org> [2.6.32+]
Signed-off-by: NDaniel T Chen <crimsun@ubuntu.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This reverts commit f41cc2a8.

The patch broke the digital mic pin handling wrongly.
Reference: bko#23162
	https://bugzilla.kernel.org/show_bug.cgi?id=23162Signed-off-by: NTakashi Iwai <tiwai@suse.de>

BugLink: http://launchpad.net/bugs/673075

According to the datasheet of 92HD87B, there is a digital mic
at nid 0x11, so enable it in order to be able to use the mic.

Cc: stable@kernel.org
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some HP laptops have lower amplifier levels for speakers in comparison
with headphone outputs.  This patch changes the BTL amp level for these
machines to balance both the speaker and headphone output levels.
Signed-off-by: NVitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The bit value set for TLV mute was wrong in commit
de8c85f7, which resulted in bogus
dB ranges that screw up PulseAudio.  Corrected with the right constant.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Windows may leave pin power-down registers set after reboot, and
this resulted in muted output on Linux.  Reset these registers
at initialization properly.
Signed-off-by: NCharles Chin <Charles.Chin@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The HDA specification does not allow for a codec to mute itself just
because the volume is reduced, so _of course_ somebody had to go and do
it.  This wouldn'\''t hurt too much when the volume is adjusted by hand,
but programs like PA that try to set the volume automatically could
inadvertently mute the output.

To work around this, change the TLV dB information for the Master volume
on all Sigmatel HDA codecs to indicate the the minimal volume setting
actually mutes.
Reported-by: NColin Guthrie <gmane@colin.guthr.ie>
Reported-by: N"Alexander E. Patrakov" <patrakov@gmail.com>
Tested-by: NColin Guthrie <cguthrie@mandriva.org>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

BugLink: https://bugs.launchpad.net/bugs/653420

Add another HP DV6 notebook (103c:363e) to use STAC_HP_DV5.
Signed-off-by: NLuke Yelavich <luke.yelavich@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix bug in switching between dmic and mic when both use the same mux.
Signed-off-by: NVitaliy Kulikov  <Vitaliy.Kulikov@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Replace the explicit ifdef check and call of check_power_status ops with
a new helper function, hda_call_check_power_status().
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Make the helper function to give the input-pin attribute for jack
connectivity and location.  This simplifies checks of input-pin jacks
a bit in some places.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NCharles Chin <Charles.Chin@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch improves the input-source label strings to be generated from
the pin information instead of fixed strings per AUTO_PIN_* type.
This gives more suitable labels, especially for mic and line-in pins.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

We can assign multiple pins to a single role now, let's reduce the
redundant FRONT_MIC and FRONT_LINE.  Also, autocfg->input_pins[] is
no longer used, so this is removed as well.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Keep char array in the input_mux item itself instead of pointing to
an external string.  This is a preliminary work for improving the
input-mux name based on the pin role.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Changing the way the input controls are named using port connection
type and jack location info.
Signed-off-by: NVitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Adding support for digital MIC in 92HD83/90/91XXX codecs family.
Signed-off-by: NVitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Just added new codec ids.  These are almost compatible with existing ones.
Signed-off-by: NCharles Chin <Charles.Chin@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the entries for 92HD87B1/3 and 92HD87B2/4 codecs.
These are compatible with existing 83xxx codecs.
Signed-off-by: NCharles Chin <Charles.Chin@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

  This provides a new model and pin config for the snd-hda-intel
92HD83XXX codec for hp laptop model dv7-4000, enabling the subwoofer.

Signed-off-by: Steven Eastland <seastland at gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix HDA beep frequency on IDT 92HD73xx and 92HD71Bxx codecs.
These codecs use the standard beep frequency calculation although the
datasheet says it's linear frequency.

Other IDT/STAC codecs might have the same problem.  They should be
fixed individually later.
Signed-off-by: NDaniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

BugLink: https://launchpad.net/bugs/576160

Symptom: Currently (2.6.32.12) the Dell M1730 uses the 3stack model
quirk. Unfortunately this means that capture is not functional out-
of-the-box despite ensuring that capture settings are unmuted and
raised fully.

Test case: boot from Ubuntu 10.04 LTS live cd; capture does not
work.

Resolution: Correct the model quirk for Dell M1730 to rely on the
BIOS configuration.

This patch also trivially sorts the quirk into the correct section
based on the comments.

Reported-and-Tested-By: <picdragon99@msn.com>
Tested-By: Daren Hayward
Tested-By: Tobias Krais
Cc: <stable@kernel.org>
Signed-off-by: NDaniel T Chen <crimsun@ubuntu.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It turned out that HP dv series have inconsistent the mute-LED GPIO
mapping among various models.  dv4/7 seem to use GPIO 0 while dv 5/6
seem to use GPIO 3.  The previous commit
  26ebe0a2
  ALSA: hda - Fix mute-LED GPIO pin for HP dv series
breaks dv5/6.

This patch adds the new quirk model, hp-dv4, to handle HP dv4/7
separately from HP dv5/6.

Tested-by: Kunal Gangakhedkar <kunal.gangakhedkar@gmail.com> (for dv6-1110ax)
Acked-by: NKunal Gangakhedkar <kunal.gangakhedkar@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Old HP dv series seem to use the GPIO pin 0 for controlling the mute LED
although the pin is a large package, where the newer models use GPIO 3
in such a case.  For fixing the regression from the previous kernels,
set spec->gpio_led statically for these model quirks.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This reverts part of commit 52dc4386, in order to fix a regression:
broken SPDIF output on Intel DG45FC motherboard (IDT 92HD73E1X5 codec).

	--- DG45FC-IDT-codec-2.6.32  (SPDIF OK)
	+++ DG45FC-IDT-codec-2.6.33  (SPDIF broken)

	 Node 0x22 [Pin Complex] wcaps 0x400301: Stereo Digital
	   Pincap 0x00000010: OUT
	-  Pin Default 0x40f000f0: [N/A] Other at Ext N/A
	-    Conn = Unknown, Color = Unknown
	-    DefAssociation = 0xf, Sequence = 0x0
	-  Pin-ctls: 0x00:
	+  Pin Default 0x014510a0: [Jack] SPDIF Out at Ext Rear
	+    Conn = Optical, Color = Black
	+    DefAssociation = 0xa, Sequence = 0x0
	+  Pin-ctls: 0x40: OUT
	   Connection: 3
	      0x25* 0x20 0x21
	 Node 0x23 [Pin Complex] wcaps 0x400301: Stereo Digital
	   Pincap 0x00000010: OUT
	-  Pin Default 0x01451140: [Jack] SPDIF Out at Ext Rear
	+  Pin Default 0x074510b0: [Jack] SPDIF Out at Ext Rear Panel
	     Conn = Optical, Color = Black
	-    DefAssociation = 0x4, Sequence = 0x0
	-    Misc = NO_PRESENCE
	-  Pin-ctls: 0x40: OUT
	+    DefAssociation = 0xb, Sequence = 0x0
	+  Pin-ctls: 0x00:
	   Connection: 3
	      0x26* 0x20 0x21

Cc: <stable@kernel.org>
Cc: Alexey Fisher <bug-track@fisher-privat.net>
Tested-by: NDavid Härdeman <david@hardeman.nu>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

BugLink: https://launchpad.net/bugs/568600

The OR has verified that the dell-m6 model quirk is necessary for audio
to be audible by default on the Dell Studio XPS 1645.

This change is necessary for 2.6.32.11 and 2.6.33.2 alike.
Reported-by: NAndy Ross <andy@plausible.org>
Tested-by: NAndy Ross <andy@plausible.org>
Cc: <stable@kernel.org>
Signed-off-by: NDaniel T Chen <crimsun@ubuntu.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

BugLink: https://launchpad.net/bugs/553002

The OR has verified that the dell-m6 model quirk is necessary for audio
to be audible by default on the Dell Studio XPS 1645.

This change is necessary for 2.6.32.11 and 2.6.33.2 alike.

Reported-by: Robert Chambers
Tested-by: Robert Chambers
Cc: <stable@kernel.org>
Signed-off-by: NDaniel T Chen <crimsun@ubuntu.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Adding this PCI quirk fixes the board config detection.
This also fixes jack sensing by using "hp_detect=1" via properly detected
board config.
Signed-off-by: NKunal Gangakhedkar <kunal.gangakhedkar@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The previous commit caused a regression on HP laptops with 92HD83x/88x
codecs.  The default polarity of mute-LED GPIO is inverted on these
devices.

Reference: Novell bnc#578190
	https://bugzilla.novell.com/show_bug.cgi?id=578190Signed-off-by: NTakashi Iwai <tiwai@suse.de>

We have now a better mute-LED GPIO detection, and no need to assign the
values statically per model option.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Merge the mute-LED status callback function for both IDT 92HD7x and 8x
codecs to one function.  Also it's changed to check all DACs, and called
in the initialization to sync with the current status.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The GPIO pin number for the mute LED control on HP laptops can be
determined more easily by checking the number of available GPIO pins
of the codec chip.  On a small package with up to 3 GPIOs, GPIO 0 is
used while GPIO 3 is used for others.

This fixes the missing mute GPIO for some HP laptops with new codecs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch fixes docking output support for IDT 92HD81/83/88 family codecs.
Typically one of ports 0xE or 0xF is used for docking output, while only
port 0xF is common on all the three codec families.  We don't want the
pin to select the analog mixer here.
Signed-off-by: NCharles Chin <Charles.Chin@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NVitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NCharles Chin <Charles.Chin@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>