In the current generic parser code, we look for the (mic) boost
controls only on input pins.  But many codecs assign the boost volume
to a widget connected to each input pin instead of the input amp of
the pin itself.

In this patch, the parser tries to look through more widgets connected
to the pin and find a boost amp.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When an amp in the activation path is associated with mixer controls,
activate_amp() tries to skip the initialization.  It's good, but only
if the mixer really initializes both mute and volume.  Otherwise,
either the mute of the volume is left uninitialized.

This patch adds this missing check and properly initialize the
partially controlled amps in an activation path.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

There are a few places creating the labels and indices of kctls for
each input pin in the current generic parser code.  This is redundant
and makes harder to maintain.  Let's create the labels and indices at
once and keep them in hda_gen_spec.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since the imux table entries can be a subset of autocfg.input table,
the indices of these aren't always same.  For passing the proper index
value of autocfg.input at creating input ctl labels (via
snd_hda_autocfg_input_label()), keep the corresponding autocfg.input
idx value in the index field of each imux item, which isn't used in
the generic driver.

Also, this makes easier to check the invalid imux pin for stereo mix.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the volume or mute control of the primary output is shared with
other (headphone or speaker) outputs, we shouldn't name it as a
specific output type but rather name it with the channel name or a
generic name like "PCM".

Also, this check should be performed individually for the volume and
the mute controls because some codecs may have shared volumes but
separate mute controls.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Not only PCM playback, a hook for PCM capture would be required for
power controls in codec drivers.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since the generic parser reduces the ADC list, copy the list of the
all detected ADCs and keep it.

This list can be later referred by the codec driver for finer power
controls.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add vmaster_tlv[] to hda_gen_spec and store the suggested TLV data
in snd_hda_gen_parse_auto_config().  This allows the codec driver to
correct the TLV data (e.g. mute capability) before actually creating
vmaster instance.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Just like the jack mode enum ctls for output jacks, add the support
for similar enum ctls for input pins to control the bias Vref.
The new controls will be added when spec->add_in_jack_modes is set
either by the codec driver or by a hint string.

Note that ground and 100% vrefs are excluded from the list for
simplicity, currently.  We may add a new flag to allow them, too.
But I guess it's easier to put a value override in the pinfix in such
a case.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

A new flag to skip the auto-mute handling in the generic parser, just
like suppress_auto_mic flag.  It has to be set before calling
snd_hda_gen_parse_auto_config().
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

... to be referred by the codec driver.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

... and a little bit of code refactoring.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Otherwise no PCM will be built for codecs without analog I/O.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Otherwise setting the capture volume for amps will be weird and
inconsistent (it will try to set values outside the range of the
second amp based on capabilities of the first amp).
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

If the input node does not have any volume capable input amp,
don't add such a control.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Even a single DAC can output two channels, so the channel count
is twice the number of DACs.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

We use knew->index for adc_idx when we create "Capture Volume" and
"Capture Switch", so use the same to retrieve adc_idx.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This gives us some additional safety.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a new flag to indicate whether HP amp is turned on as default for
speaker or line-outs, and enable this for ALC260 codec, as many
machines with this codec require the HP amp even for speakers.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a hook for the capture mixer switch.  This will be used by IDT
codecs for controlling the mic-mute LED.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Through the hints via sysfs or patch, user can set specific behavior
flags for the generic parser now.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add the enum controls for changing the headphone amp bits of output
jacks, such as "Headphone Jack Mode".  This feature isn't enabled as
default, so far, unless spec->add_out_jack_modes flag is set.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When a multi-io jack is switched to another direction, call the
automute and autoswitch update functions, as this jack won't be used
as the headphone or the mic jack that may turn off others.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When a jack is retasked as a different direction (e.g. a mic jack is
used as a CLFE output), such a jack shouldn't be counted as the target
for the automatic jack switching.  Skip the automute or the autoswitch
when the current pinctl direction is different from what we suppose.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use the new pin target accessors for managing the current pinctl
values in the generic parser.  The pinctl values of all active pins
are once determined at the initialization phase, and stored via
snd_hda_codec_set_pin_target().  This will be referred again in the
codec init or resume phase to set the actual pinctl.

This value is kept while the auto-mute.  When a line-out or a speaker
pin is muted by auto-mute, the driver simply disables the pin, but it
doesn't touch the cached pinctl target value.  Upon unmute, this value
is used to restore the original pinctl in return.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When a DAC is reassigned from surrounds to front or ADCs are reduced
due to incomplete imux, we clear the path indices but the path
instances remain as is.  Since the paths might be still referred
through the whole path list parsing (e.g. is_active_nid()), we should
clear these path instances as well.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since some codecs can choose the aamix as a capture source, we should
support it as well.  When spec->add_stereo_mix_input flag is set, the
parser checks the availability of aamix as the input source, and adds
the paths automatically when possible.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In the current parser code, the input_paths[] may become inconsistent
when some of detected ADCs are dropped due to incomplete inputs, since
the driver rearranges only adc_nids[] but doesn't touch input_paths[].

This patch fixes the issue, and also it optimizes the reachability
checks by simply referring to the parsed input_paths[] instead of
calling is_reachable() again for each connection.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Instead of handling special cases in the caller side, give a proper
name string "Headphone Mic" from hda_get_autocfg_input_label() when
the headhpone jack pin is specified as an input.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The capture paths shouldn't contain the analog loopback mixer.
Pass a proper argument to exclude the aamix NID.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a new flag spec->suppress_mic_auto_switch for codecs that don't
support unsol events properly like VT1708.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit modifies the definition of snd_hda_parse_nid_path()
slightly, now with_aa_mix argument is changed to anchor_nid, so that
it can handle any NID generically as an anchor point to include or
exclude.

The with_aa_mix field in struct nid_path is removed again by this
change.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

... like we did for output and loopback paths.
It makes the code slightly easier.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The multi-io channels can vary not only from 1 to 6 but also may vary
from 6 to 8 or such.  At the same time, there are more speaker pins
available than the primary output pins.  So, we need three variables
to check: the minimum channel counts for primary outputs, the current
channel counts for primary outputs, and the minimum channel counts for
all outputs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Remove useless code.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Instead of looking through paths with the dac -> pin connection at
each time, just pass the already parsed path index to
assign_out_path_ctls().  This simplifies the code a bit.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The path indices must be reset at each evaluation of DAC assignment.
Otherwise the badness value will be wrongly calculated and mixers may
be inconsistently assigned.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Just to remove duplicated codes.
Also fixed EXPORT_SYMBOL() in hda_generic.c.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>