On Panda the +5V supply for DVI EDID is supplied by the
same regulator that poweres the USB Hub. Currently, the
DSS/DVI subsystem doesn't know how to manage this regulator
and so DVI EDID reads will fail if USB Hub is not enabled.

As a temporary fix we keep this regulator permanently enabled
on boot. This fixes the DVI EDID read problem.

CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Provide the RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.

Also provide pin multiplexer information for the USB host
pins.

HACK: The reset control need to be replaced with the proper
gpio-controlled reset driver as soon it will be merged [1].
[1] http://thread.gmane.org/gmane.linux.drivers.devicetree/36830Signed-off-by: NRoger Quadros <rogerq@ti.com>
[benoit.cousson@linaro.org: Add disclaimer about the reset control
inside changelog and code]
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add AM43x ePOS EVM minimal DT source - this is a minimal one to get
it booting. Also include it in omap2plus dtbs and document bindings.
The hardware is under development.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add bandgap device DT entry for OMAP5 dtsi.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: NEduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: NJ Keerthy <j-keerthy@ti.com>
[benoit.cousson@linaro.org: Fix alignement and use the macros
for IRQ attributes]
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add pinmux configurations for RGMII based CPSW ethernet to am335x-evm.

Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.

Sleep mode is nothing but the values required for the module during
inactive state. The pins are configured to its reset state to optimize
energy usage for the pins for the suspend/resume cycle
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add pinmux configurations for RGMII based CPSW ethernet to AM335x EVMsk.

Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.

Sleep mode is nothing but the values required for the module during
inactive state. The pins are configured to its reset state to optimize
energy usage for the pins for the suspend/resume cycle
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add pinmux configurations for MII based CPSW ethernet to am335x-bone.

Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.

Sleep mode is nothing but the values required for the module during
inactive state. The pins are configured to its reset state to optimize
energy usage for the pins for the suspend/resume cycle
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Commit c971ff18 'leds: leds-pwm: Defer led_pwm_set() if PWM can sleep'
fixed a crash when using a trigger with a pwm-led provided by an
external chip. Now it is safe to add the default trigger according
to board-overo.c.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The LED is active low, not active high.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The Tobi expansion boards embeds a SMSC LAN8700 PHY. Add the
corresponding node into the DT. The regulators are not designed
to be turned off.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Some nodes in OMAP3 DTS now use edge or level sensitive interrupts.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Pinctrl headers were not protected with #ifndef.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

clkout2 comes out on the pad and is being used by various
external on-board peripherals like, Audio codecs and stuff.
So enable the clkout2 by default during init sequence itself.

Also, add the missing entry of "clkout2_ck" to the clock table.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Represent debugSS clock interface as provided in
CM_WKUP_DEBUGSS_CLKCTRL register, includes
	- Clock gate for optional DEBUG_CLKA and DBGSYSCLK
	- Clock Mux for TRC_PMD and STM_PMD
	- Clock divider for STM and TPIU
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add Palmas MFD node and the regulator nodes for OMAP5.

The node definitions are based on: https://lkml.org/lkml/2013/6/6/25

Boot tested on omap5-uevm board.
Signed-off-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NJ Keerthy <j-keerthy@ti.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

PWM output from ecap2 uses as backlight source. Also adds low threshold
value to have a uniform divisions in brightness-levels scales with
inverse polarity.
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
Reviewed-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

PWM output from ecap0 uses as backlight source. Also adds low threshold
value to have a uniform divisions in brightness-levels scales.
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
Reviewed-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add PWMSS device tree nodes in relation with ECAP & EHRPWM DT nodes to
AM33XX SoC family. Also populates device tree nodes for ECAP & EHRPWM by
adding necessary properties like pwm-cells, base reg & set disabled as
status.
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
Reviewed-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add bandgap devices for OMAP4460 devices.
Signed-off-by: NEduardo Valentin <eduardo.valentin@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add the bandgap entry for OMAP4430 devices.
Signed-off-by: NEduardo Valentin <eduardo.valentin@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
[benoit.cousson@linaro.org: Add blank line and fix reg presentation]
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

On most OMAP3 platforms, the twl4030 IRQ line is connected to the
SYS_NIRQ line on OMAP.  Add another DTS include file
(twl4030_omap3.dtsi) for boards that hook up the twl4030 this way
to include.

This allows RTC wake from off-mode to work again on OMAP3-based
platforms with twl4030.  Tested on 3530/Beagle, 3730/Beagle-xM,
3530/Overo, 3730/Overo-STORM.

Special thanks to Florian Vaussard for suggesting use of preprocessor
feature.

Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Using the gpio-keys bindings, configure the user button on Beagle
boards.  Since the user button is enabled as a wakeup source, also
ensure the GPIO pin is mux'd correctly and has IO ring wakeups enabled,
so it can also wakeup from off mode.

Special thanks to Florian Vaussard for suggesting the preprocessor
feature.

Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Ensure the console uart (UART3) on these boards is mux'd correctly, and
IO ring wakeup is enabled.

This is needed for serial console wakeups when using DT boot.

Thanks to Florian Vaussard for suggestion to use preprocessor
features.

Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Booting omap5 uevm results in the following error
"did not get pins for uart error: -19"

This happens because omap5 uevm dts file is not adapted
to use uart through pinctrl framework.
Populate uart pinctrl data to get rid of the error.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: NSricharan R <r.sricharan@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add support for blue LED 1 off of GPIO 153.
Make the LED a heartbeat LED
Configure the MUX for GPIO output.
Signed-off-by: NDan Murphy <dmurphy@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: NSricharan R <r.sricharan@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Provide the RESET regulators for the USB PHYs, the USB Host
port modes and the PHY devices.

Also provide pin multiplexer information for the USB host
pins.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: NSricharan R <r.sricharan@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The uevm is the only official board supported for the OMAP5 soc
in mainline. The existent sevm platform will no more be supported.
Hence cleaning up the board dts file to have only the data
required for uevm.

Renaming the board dts file and adding the following cleanups.

 * There are no devices connected on I2C 2,3,4 buses. So remove
   the pinmux data for the same.

 * OMAP5432 and DDR3 memory is used in the uevm. Temperature polling
   is not supported with DDR3 memories. Because of DDR3 phy limitation
   the voltage change across DVFS and all shadow registers for DVFS on
   DDR3 is not supported. Hence the emif kernel driver is not required,
   so removing the DDR3 device file and emif nodes for uevm.

 * Keypad is not supported on uevm. So remove the device node.
Signed-off-by: NSricharan R <r.sricharan@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

When making the dtbs target on OMAP/AM35xx, some trees are not
built.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Using constants for pinctrl allows a better readability, and removes
redundancy with comments.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The pinctrl IP inside the AM33XX family differs slightly from
what is found on OMAP2+. Define a specific header to take account
of the differences.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Use standard GPIO constants to enhance the readability of DT GPIOs.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Replace /include/ by #include for AM33XX and AM35XX device tree
files, in order to use the C pre-processor, making use of #define
features possible.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

DT source (minimal) for AM4372 SoC to represent AM43x SoC's. Those
represented here are the minimal DT nodes necessary to get kernel
booting.

In DT nodes, "ti,hwmod" property has not been added, this would be
added along with PRCM support for AM43x.
Signed-off-by: NAnkur Kishore <a-kishore@ti.com>
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Update the dt property ti,audpwron-gpio to use the
gpio macro definition for GPIO_ACTIVE_HIGH.
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Reviewed-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The GPIO for LED D1 on the omap4-panda a1-a3 rev and the omap4-panda-es
are different.

A1-A3 = gpio_wk7
ES = gpio_110

There is no change to LED D2

Abstract away the pinmux and the LED definitions for the two boards into
the respective DTS files.
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Using constants for pinctrl allows a better readability, and removes
redundancy with comments.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Most of the constants are taken from arch/arm/mach-omap2/mux.h.
Define some others for the PIN_OUTPUT_* flavours.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Use the constants defined in include/dt-bindings/interrupt-controller/
to enhance readability.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Use standard GPIO constants to enhance the readability of DT GPIOs.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Replace /include/ by #include for OMAP2+ DT, in order to use the
C pre-processor, making use of #define features possible.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>