This supports future devices with fewer GPIOs.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Better support future device revisions by moving some of the output
around and making the chip ID enumeration be the value expected in
the ID register.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The name field of struct i2c_client is for i2c-core's use, it should
never be changed by the drivers themselves.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When building the driver as a module, module_exit was missing, and
subsys_initcall_sync() is not defined.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds core driver support for AB4500 mixed signal
multimedia & power management chip. This connects to U8500
on the SSP (pl022) and exports read/write functions for
the device to get access to this chip. This also registers
the client devices and sets the parent.
Signed-off-by: Nsrinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: NAndrea Gallo <andrea.gallo@stericsson.com>
Reviewed-by: NMark Brown <broonie@sirena.org.uk>
Reviewed-by: NJean-Christophe <plagnioj@jcrosoft.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds a core driver for 88PM8607 found in Marvell DKB development
platform. This driver is a proxy for all accesses to 88PM8607
sub-drivers which will be merged on top of this one, RTC, regulators,
battery and so on.

This chip is manufactured by Marvell.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

There was confusion between the array size and the highest ISEL
value possible.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds platform data with a function for power
control to the SDHI driver. The idea is that board specific
code can provide their own functions so power can be enabled
and disabled for the sd-cards.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The old access methods to the gpios will be removed when
all users has been converted. (mainly ucb1x00-ts)

So drivers like collie_battery driver can use
those files easier.

Since twl4030_probe is only called from functions in the init ELF
section, annotate it so.
Signed-off-by: NDaniel J Blueman <daniel.blueman@gmail.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Configure the APLL_INFREQ field in the APLL_CTL register
based on the platform data.
Provide also a function for childs to query the audio_mclk
frequency.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

New MFD child to twl4030 MFD device.

Reason for the twl4030_codec MFD: the vibra control is actually in the codec
part of the twl4030. If both the vibra and the audio functionality is needed
from the twl4030 at the same time, than they need to control the codec power
and APLL at the same time without breaking the other driver.
Also these two has to be able to work without the need for the other driver.

This MFD device will be used by the drivers, which needs resources
from the twl4030 codec like audio and vibra.

The platform specific configuration data is passed along to the
child drivers (audio, vibra).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch allows UCB1400 to get IRQ GPIO from platform data. In case
platform_data are not supplied or the IRQ supplied in the platform_data
is negative, fall back to the old IRQ detection algorithm.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Configure the APLL_INFREQ field in the APLL_CTL register
based on the platform data.
Provide also a function for childs to query the audio_mclk
frequency.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We are mistakenly dereferencing twl->client in the twl->client null checking
path.
Signed-off-by: NIlkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This avoids crashes when running without interrupt support.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds an MFD driver for the SuperH Mobile SDHI
hardware block. At this point the driver simply wraps the
tmio-mmc driver with some clock code. In the future this
driver is the place to put SDHI specific hotplug code.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

New MFD child to twl4030 MFD device.

Reason for the twl4030_codec MFD: the vibra control is actually in the codec
part of the twl4030. If both the vibra and the audio functionality is needed
from the twl4030 at the same time, than they need to control the codec power
and APLL at the same time without breaking the other driver.
Also these two has to be able to work without the need for the other driver.

This MFD device will be used by the drivers, which needs resources
from the twl4030 codec like audio and vibra.

The platform specific configuration data is passed along to the
child drivers (audio, vibra).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.

This was done with:

#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"

for header in $headers; do
	old="#include <mach\/$header"
	new="#include <plat\/$header"
	for dir in $omap_dirs; do
		find $dir -type f -name \*.[chS] | \
			xargs sed -i "s/$old/$new/"
	done
	find drivers/ -type f -name \*omap*.[chS] | \
		xargs sed -i "s/$old/$new/"
	for file in $other_files; do
		sed -i "s/$old/$new/" $file
	done
done

for header in $(ls $mach_dir_old/*.h); do
	git mv $header $plat_dir_new/
done
Signed-off-by: NTony Lindgren <tony@atomide.com>

The usb regulator supplies (usb1v5, usb1v8 & usb3v1) must be available
before adding the twl4030_usb child, else twl4030_usb_ldo_init() will
always fail thus causing boot lock-up.

This patch fixes boot on OMAP systems using the twl4030 usb transceiver.
CONFIG_TWL4030_USB=y
Signed-off-by: NRoger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The I2C_CLIENT_INSMOD_1 macro is only useful for i2c drivers which
implement device detection. The ab3100 driver doesn't, so there is no
point in calling it.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>

Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This makes it consistent with other buses (platform, i2c, vio, ...).  I'm
not sure why we use the prefixes, but there must be a reason.

This was easy enough to do it, and I did it.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/mfd/ab3100-core.c:647: error: ab3100_init_settings causes a section type conflict

Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Instead of hand rolling our own variant.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

KEY_1 and KEY_2 definitions conflicts with include/linux/input.h
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds support for the regulators found in the AB3100
Mixed-Signal IC.

It further also defines platform data for the ST-Ericsson
U300 platform and extends the AB3100 MFD driver so that
platform/board data with regulation constraints and an init
function can be passed down all the way from the board to
the regulators.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

ab3100.h should include linux/workqueue.h for otp to build properly.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When the sleep script is loaded before the wakeup script, there is a
chance that the system might go to sleep before the wakeup script
loading is completed. This will lead to a system that does not wakeup
and has been observed to cause non-booting boards.

Various options were considered to solve this problem, including
modification of the core twl4030 power code to be smart enough to
reorder the loading of the scripts. But it felt too over-engineered.

Hence this patch just warns the DPS script developer so that they may be
reordered in the board-code itself.
Signed-off-by: NAmit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The TWL4030/5030 family of multifunction devices allows board-specific
control of the the various regulators, clock and reset lines through
'scripts' that are loaded into its memory. This allows for Dynamic Power
Switching (DPS).

Implement board-independent core support for DPS that is then used by
board-specific code to load custom DPS scripts.
Signed-off-by: NAmit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds the ability to read out OTP (One-Time Programmable)
registers in the AB3100 MFD ASIC. It's a simple sysfs file you
can cat to prompt. The OTP registers of the AB3100 are used to
store various device-unique information such as customer ID,
product flags and the 3GPP standard IMEI (International Mobile
Equipment Indentity) number.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This driver provides the core Freescale MC13783 support. It
registers the client platform_devices and provides access
to the A/D converter.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This will make the worker fire interrupt disable the AB3100 IRQ
without sync which resolves a race since the interrupt obviously
cannot wait for itself to complete while being handled.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This alters the default setting for AB3100_IMRB1 from 0xff to
0xbf. These registers are used for the yet unimplemented ADC
and this new setting will deactivate ADC Trigger 1.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This makes ab3100_set_register_interruptible() propagate the error
code from suboperations properly so it can be handles properly.
(A special case comes from signal interruption.)
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds the _interruptible suffix to the AB3100 accessor
functions on par with mutex_lock_interruptible() that's used
for blocking simultaneous calls to the AB3100 acessor functions.
Since these accesses are slow on a 100kHz I2C bus and may line
up waiting for the mutex, we need to handle interruption by
system shutdown or kill signals and may just as well denote that
in the function names.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>