This change adds the ability to suppress a routing decision based upon the
interface group the selected interface belongs to. This allows it to
exclude specific devices from a routing decision.
Signed-off-by: NStefan Tomanek <stefan.tomanek@wertarbyte.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By using sizeof(_hdr), net/ipv6/raw.c:icmpv6_filter implicitly assumes
that any valid ICMPv6 message is at least eight bytes long, i.e., that
the message body is at least four bytes.

The DIS message of RPL (RFC 6550 section 6.2, from the 6LoWPAN world),
has a minimum length of only six bytes, and is thus blocked by
icmpv6_filter.

RFC 4443 seems to allow even a zero-sized body, making the minimum
allowable message size four bytes.
Signed-off-by: NWerner Almesberger <werner@almesberger.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"_hdr" should hold the ICMPv6 header while "hdr" is the pointer to it.
This worked by accident.
Signed-off-by: NWerner Almesberger <werner@almesberger.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For ethernet frames, eth_type_trans() already parses the header, so one
can skip this when checking the frame size.
Signed-off-by: NPhil Sutter <phil@nwl.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since tpacket_fill_skb() parses the protocol field in ethernet frames'
headers, it's easy to see if any passed frame is a VLAN one and account
for the extended size.

But as the real protocol does not turn up before tpacket_fill_skb()
runs which in turn also checks the frame length, move the max frame
length calculation into the function.
Signed-off-by: NPhil Sutter <phil@nwl.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This may be necessary when the SKB is passed to other layers on the go,
which check the protocol field on their own. An example is a VLAN packet
sent out using AF_PACKET on a bridge interface. The bridging code checks
the SKB size, accounting for any VLAN header only if the protocol field
is set accordingly.

Note that eth_type_trans() sets skb->dev to the passed argument, so this
can be skipped in packet_snd() for ethernet frames, as well.
Signed-off-by: NPhil Sutter <phil@nwl.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When sctp sits on IPv6, sctp_transport_dst_check pass cookie as ZERO,
as a result ip6_dst_check always fail out. This behaviour makes
transport->dst useless, because every sctp_packet_transmit must look
for valid dst.

Add a dst_cookie into sctp_transport, and set the cookie whenever we
get new dst for sctp_transport. So dst validness could be checked
against it.

Since I have split genid for IPv4 and IPv6, also delete/add IPv6 address
will also bump IPv6 genid. So issues we discussed in:
http://marc.info/?l=linux-netdev&m=137404469219410&w=4
have all been sloved for this patch.
Signed-off-by: NFan Du <fan.du@windriver.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Joe Perches says:

====================
Convert the uses mac addresses to ETH_ALEN so
it's easier to find and verify where mac addresses
need to be __aligned(2)

Change in V2:
- Remove include/acpi/actbl2.h conversion
  It's a file copied from outside ACPI sources

Changes in V3:
- Don't move the pasemi_mac.h mac address to be aligned(2)
  Just note that it's unaligned.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the normal #define to help grep find mac addresses
and ensure that addresses are aligned.

pasemi.h has an unaligned access to mac_addr, unchanged
for now.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: Olof Johansson <olof@lixom.net> # pasemi_mac pieces
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's convenient to have ethernet mac addresses use
ETH_ALEN to be able to grep for them a bit easier and
also to ensure that the addresses are __aligned(2).

Add #include <linux/if_ether.h> as necessary.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NMauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the #define where appropriate.

Add #include <linux/if_ether.h>
where appropriate too.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Himanshu Madhani says:

====================
This series contains following patches

o in v2 series, we received feedback on return codes to use standard error
  codes instead of mixing custom error codes. We have modified patch for
  loopback diagnostic test to return standard error codes.

o rest of the 3 patches in the series are for mailbox refactoring

  Current driver-firmware mailbox interface was operating in polling mode
  because of some limitations with the earlier versions of 83xx adapter
  firmware. These issues are resolved now and we are implementing the
  mailbox interface in interrupt mode.

  There are three patches which refactors mailbox handling:
  * Interrupt mode mailbox implantation.
  * Replace poll mode mailbox interfaces with interrupt mode interfaces.
  * Operate mailbox in poll mode when interrupts are not available.

changes from v2 -> v3
 * Addressed review feedback to use standard return codes for loopback
   diagnostic test.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Driver firmware mailbox interface was operating in polling mode
  because of limitations with the earlier versions of 83xx adapter firmware.
  These issues are resolved and we are implementing interrupt based mailbox
  mechanism.

o Data structures and API's for interrupt mode mailbox mechanism.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Enhanced the driver to use standard Linux error codes
o Return a unique error code to indicate loopback is in progress
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
 This patchset aims to lay the groundwork, and do the initial conversion to
RCUism. I decided that it'll be much better to make the bonding RCU
conversion gradual, so patches can be reviewed and tested better rather
than having one huge patch (which I did in the beginning, before this).
The first patch is straightforward and it converts the bonding to the
standard list API, simplifying a lot of code, removing unnecessary local
variables and allowing to use the nice rculist API later. It also takes
care of some minor styling issues (re-arranging local variables longest ->
shortest, removing brackets for single statement if/else, leaving new line
before return statement etc.).
 The second patch simplifies the conversion by removing unnecessary
read_lock(&bond->curr_slave_lock) in xmit paths that are to be converted
later, because we only care if the pointer is NULL or a slave there, since
we already have bond->lock the slave can't go away.
 The third patch simplifies the broadcast xmit function by removing
the use of curr_active_slave and converting to standard list API. Also this
design of the broadcast xmit function avoids a subtle double packet tx race
when converted to RCU.
 The fourth patch factors out the code that transmits skb through a slave
with given id (i.e. rr_tx_counter in rr mode, hashed value in xor mode) and
simplifies the active-backup xmit path because bond_dev_queue_xmit always
consumes the skb. The new bond_xmit_slave_id function is used in rr and xor
modes currently, but the plans are to use it in 3ad mode as well thus it's
made global. I've left the function prototype to be 81 chars so I wouldn't
break it, if this is an issue I can always break it in more lines.
 The fifth patch introduces RCU by converting attach/detach and release to
RCU. It also converts dereferencing of curr_active_slave to rcu_dereference
although it's not fully converted to RCU, that is needed for the converted
xmit paths. And it converts roundrobin, broadcast, xor and active-backup
xmit paths to RCU. The 3ad and ALB/TLB modes acquire read_lock(&bond->lock)
to make sure that no slave will be removed and to sync properly with
enslave and release as before.
 This way for the price of a little complexity, we'll be able to convert
individual parts of the bonding to RCU, and test them easier in the
process. If this patchset is accepted in some form, I'll post followups
in the next weeks that gradually convert the bonding to RCU and remove the
need for the rwlocks.
 For performance notes please refer to patch 5 (RCU conversion one).
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch does the initial bonding conversion to RCU. After it the
following modes are protected by RCU alone: roundrobin, active-backup,
broadcast and xor. Modes ALB/TLB and 3ad still acquire bond->lock for
reading, and will be dealt with later. curr_active_slave needs to be
dereferenced via rcu in the converted modes because the only thing
protecting the slave after this patch is rcu_read_lock, so we need the
proper barrier for weakly ordered archs and to make sure we don't have
stale pointer. It's not tagged with __rcu yet because there's still work
to be done to remove the curr_slave_lock, so sparse will complain when
rcu_assign_pointer and rcu_dereference are used, but the alternative to use
rcu_dereference_protected would've created much bigger code churn which is
more difficult to test and review. That will be converted in time.

1. Active-backup mode
 1.1 Perf recording while doing iperf -P 4
  - old bonding: iperf spent 0.55% in bonding, system spent 0.29% CPU
                 in bonding
  - new bonding: iperf spent 0.29% in bonding, system spent 0.15% CPU
                 in bonding
 1.2. Bandwidth measurements
  - old bonding: 16.1 gbps consistently
  - new bonding: 17.5 gbps consistently

2. Round-robin mode
 2.1 Perf recording while doing iperf -P 4
  - old bonding: iperf spent 0.51% in bonding, system spent 0.24% CPU
                 in bonding
  - new bonding: iperf spent 0.16% in bonding, system spent 0.11% CPU
                 in bonding
 2.2 Bandwidth measurements
  - old bonding: 8 gbps (variable due to packet reorderings)
  - new bonding: 10 gbps (variable due to packet reorderings)

Of course the latency has improved in all converted modes, and moreover
while
doing enslave/release (since it doesn't affect tx anymore).

Also I've stress tested all modes doing enslave/release in a loop while
transmitting traffic.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I factored out the tx xmit code which relies on slave id in
bond_xmit_slave_id. It is global because later it can be used also in
3ad mode xmit. Unnecessary obvious comments are removed. Active-backup
mode is simplified because bond_dev_queue_xmit always consumes the skb.
bond_xmit_xor becomes one line because of bond_xmit_slave_id.
bond_for_each_slave_from is not used in bond_xmit_slave_id because later
when RCU is used we can avoid important race condition by using standard
rculist routines.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't need to start from the curr_active_slave as the frame will be
sent to all eligible slaves anyway, so we remove the unnecessary local
variables, checks and comments, and make it use the standard list API.
This has the nice side-effect that later when it's converted to RCU
a race condition will be avoided which could lead to double packet tx.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In all the cases we already hold bond->lock for reading, so the slave
can't get away and the check != NULL is sufficient. curr_active_slave
can still change after the read_lock is unlocked prior to use of the
dereferenced value, so there's no need for it. It either contains a
valid slave which we use (and can't get away), or it is NULL which is
checked.
In some places the read_lock of curr_slave_lock was left because we need
it not to change while performing some action (e.g. syncing current
active slave's addresses, sending ARP requests through the active slave)
such cases will be dealt with individually while converting to RCU.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch aims to remove struct bonding's first_slave and struct
slave's next and prev pointers, and replace them with the standard Linux
list API. The old macros are converted to list API as well and some new
primitives are available now. The checks if there're slaves that used
slave_cnt have been replaced by the list_empty macro.
Also a few small style fixes, changing longest -> shortest line in local
variable declarations, leaving an empty line before return and removing
unnecessary brackets.
This is the first step to gradual RCU conversion.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Server           Client
2001:1::803/64  <-> 2001:1::805/64
2001:2::804/64  <-> 2001:2::806/64

Server side fib binary tree looks like this:

                                   (2001:/64)
                                   /
                                  /
                   ffff88002103c380
                 /                 \
     (2)        /                   \
 (2001::803/128)                     ffff880037ac07c0
                                    /               \
                                   /                 \  (3)
                      ffff880037ac0640               (2001::806/128)
                       /             \
             (1)      /               \
        (2001::804/128)               (2001::805/128)

Delete 2001::804/64 won't cause prefix route deleted as well as rt in (3)
destinate to 2001::806 with source address as 2001::804/64. That's because
2001::803/64 is still alive, which make onlink=1 in ipv6_del_addr, this is
where the substantial difference between same prefix configuration and
different prefix configuration :) So packet are still transmitted out to
2001::806 with source address as 2001::804/64.

So bump genid will clear rt in (3), and up layer protocol will eventually
find the right one for themselves.

This problem arised from the discussion in here:
http://marc.info/?l=linux-netdev&m=137404469219410&w=4Signed-off-by: NFan Du <fan.du@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
this is a pull-request for net-next/master. It consists of two patches
by Fabio Estevam. Them first convert the flexcan driver to use
devm_ioremap_resource(), the second adds return value checking for
clk_prepare_enable().
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On very rare occasions, repeated load/unload stress test in the presence of
our storage driver (bnx2i/bnx2fc) causes a kernel panic in bnx2x code
(NULL pointer dereference). Stack traces indicate the issue happens during MAC
configuration; thorough code review showed that indeed several races exist
in which one thread can iterate over the list of configured MACs while another
deletes entries from the same list.

This patch adds a varient on the single-writer/Multiple-reader lock mechanism -
It utilizes an already exsiting bottom-half lock, using it so that Whenever
a writer is unable to continue due to the existence of another writer/reader,
it pends its request for future deliverance.
The writer / last readers will check for the existence of such requests and
perform them instead of the original initiator.
This prevents the writer from having to sleep while waiting for the lock
to be accessible, which might cause deadlocks given the locks already
held by the writer.

Another result of this patch is that setting of Rx Mode is now made in
sleepable context - Setting of Rx Mode is made under a bottom-half lock, which
was always nontrivial for the bnx2x driver, as the HW/FW configuration requires
wait for completions.
Since sleep was impossible (due to the sleepless-context), various mechanisms
were utilized to prevent the calling thread from sleep, but the truth was that
when the caller thread (i.e, the one calling ndo_set_rx_mode()) returned, the
Rx mode was still not set in HW/FW.

bnx2x_set_rx_mode() will now overtly schedule for the Rx changes to be
configured by the sp_rtnl_task which hold the RTNL lock and is sleepable
context.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 4aa5dee4 ("net: convert resend IGMP to notifier event")
we try to acquire rtnl in bond_resend_igmp_join_requests but it can be
scheduled with rtnl already held (e.g. when bond_change_active_slave is
called with rtnl) causing a loop of immediate reschedules + calls because
rtnl_trylock fails each time since it's being already held.
For me this issue leads to system hangs very easy:
modprobe bonding; ifconfig bond0 up; ifenslave bond0 eth0; rmmod
bonding;

The fix is to introduce a small (1 jiffy) delay which is enough for the
sections holding rtnl to finish without putting any strain on the system.
Also adjust the timer in bond_change_active_slave to be 1 jiffy, since
most of the time it's called with rtnl already held.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The initial driver support was for a single mPIPE shim on the chip
(as is the case for the Gx36 hardware).  The Gx72 chip has two mPIPE
shims, so we extend the driver to handle that case.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code used to call napi_disable() in an interrupt handler
(from smp_call_function), which in turn could call msleep().
Unfortunately you can't sleep in an interrupt context.

Luckily it turns out all the NAPI support functions are
just operating on data structures and not on any deeply
per-cpu data, so we can arrange to set up and tear down all
the NAPI state on the core driving the process, and just
do the IRQ enable/disable as a smp_call_function thing.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Building against headers from an older Tilera hypervisor can cause
the frags[] array to be overrun.  Don't enable TSO in that case.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change allows the user to configure various features of the tile
networking drivers on and off.  There is no change to the default
initialization state of either the tilegx or tilepro drivers.

Neither driver needs the ndo_fix_features or ndo_set_features callbacks,
since the generic code already handles the dependencies for
fix_features, and there is no hardware state to tweak in set_features.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>