There's no reason for the third parameter of ipath_count_units() to be
a u32 *, so change it to be an int * instead.  This fixes the sparse
warning:

    drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47: warning: incorrect type in argument 3 (different signedness)
    drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47:    expected unsigned int [usertype] *maxportsp
    drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47:    got int *<noident>
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Subnet manager SetPortinfo messages distingush between changing the link
state (DOWN, ARM, ACTIVE) and the link physical state (POLL, SLEEP,
DISABLED).  These are somewhat independent commands and affect when link
width and speed changes take effect.  Without this patch, a link DOWN
physical state NOP command was causing the link width and speed settings
to take effect which should only happen when the link physical state is
goes down (either by a SMP or some link physical error like link errors
exceeding the threshold).
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The IBA7220 uses a count-based triggering mechanism, and therefore
can't use the same bandwidth verification mechanism as older chips.

To support the 7220, allow enabling and disabling armlaunch errors on
application request.  Minor robustness improvements as well.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This code has been unused for some time, but still had leftovers
from when it was used.

Signed-off-by: Dave Olson <dave.olson@qlogic.com
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The 6110 had a bug that caused some registers to be swapped; it was
fixed for the 7220 (and didn't affect the 6120 because it had fewer
registers).  This adds a flag and related code to handle that, and
includes some minor cleanups in the same area.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>

Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

kreceive is now portdata * instead of devdata * and other kreceive
related cleanups....
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove an unused parameter and fix up the comment.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Code review pointed out that the locking around uses of ipath_sendctrl 
and kr_sendctrl were, in several places, incorrect and/or inconsistent.
Signed-off-by: NJohn Gregor <john.gregor@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Make the ipath driver use the new driver functions so that it does not
touch the sysfs portion of the driver structure.

We also remove the redundant symlink from the device back to the driver,
as it is already in the sysfs tree.  Any userspace tools should be using
the standard symlink, not some driver specific one.

Cc: Roland Dreier <rdreier@cisco.com>
Cc: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: Arthur Jones <arthur.jones@qlogic.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The link state event calls were being generated when the SM told the SMA
to change link states. This works for IB_EVENT_PORT_ACTIVE but not if
the link goes down and stays down. The fix is to generate event calls
from the interrupt handler when the HW link state changes.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch removes some redundant initialization code.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There have been a number of issues where host bandwidth via HT or PCIe
to the InfiniPath chip has been limited in some fashion (BIOS,
configuration, etc.), resulting in user confusion.  This check gives a
clear warning that something is wrong and needs to be resolved.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There was confused use of INFINIPATH_S_PIOBUFAVAILUPD (value) and
IPATH_S_PIOBUFAVAILUPD (bit position).  Also, some callers of
ipath_cancel_sends() need kr_sendctrl restored, and some want to do it
later.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Make some functions that are only used in a single .c file static.  In
addition to being a cleanup, this shrinks the generated code.  On x86_64:

add/remove: 1/3 grow/shrink: 2/1 up/down: 4777/-4956 (-179)
function                                     old     new   delta
handle_errors                                  -    3994   +3994
__verbs_timer                                 42     710    +668
ipath_do_ruc_send                           2131    2246    +115
ipath_no_bufs_available                      136       -    -136
ipath_disarm_senderrbufs                     639       -    -639
ipath_ib_timer                               658       -    -658
ipath_intr                                  5878    2355   -3523
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.

This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.

In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.

Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Acked-by: NDave Jones <davej@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All too often, interrupts do not get enabled for our card due to BIOS
misconfiguration and other issues.  This patch checks for that
condition on startup and warns the user.  This patch is based on work
(check LID availability) by Robert Walsh.
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Clean up some code by removing support for some older pre-production
HTX InfiniPath cards.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>

Now that it's June, it's about time to update
the copyright notices of files that have changed.
Signed-off-by: NJohn Gregor <john.gregor@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This centralizes the use of the abort functionality, removes the
unneeded buffer cancel (abort does the same thing), sets up to ignore
launch errors after abort, same as cancel.  We need abort on exit from
freeze mode to avoid having buffers stuck in the busy state, if a user
process happened to complete the send while we were in freeze mode
doing the recovery.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

We currently track various errors, now we enhance that capability by
logging some of them to EEPROM.  We also now log a cumulative "active"
time defined by traffic though the InfiniPath HCA beyond the normal SM
traffic.
Signed-off-by: NMichael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When we want to find an InfiniPath HCA in a rack of nodes, it is often
expeditious to blink the status LEDs via a userspace /sys file.

A write-only led_override "file" is published per device. Writes to
this file are interpreted as (string form) numbers, and the resulting
value sent to ipath_set_led_override(). The upper eight bits are
interpretted as a 4.4 fixed-point "frequency in Hertz", and the bottom
two 4-bit values are alternately (D0..3, then D4..7) used by the
board-specific LED-setting function to override the normal state.
Signed-off-by: NMichael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Move the code that shuts down the IB link earlier in the unload
process, to be sure no new packets can arrive while we are unloading.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Mostly cleanup.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In initialization, if we bailed at chip specific initialization, we
forgot to clean up the irq we had requested.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Some types of packet errors are moderately common with longer IB
cables and large clusters, and are not reported with prints by other
IB HCA drivers.  This suppresses those messages unless the new
__IPATH_ERRPKTDBG bit is set in ipath_debug.  Reporting of temporarily
disabled frequent error interrupts was also made clearer

We also distinguish between chip errors, and bad packets sent or
received in the wording of the messages.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ipath_dbg doesn't need the same prefixes that printk does.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This is a sticky state.  It is useful for diagnosing problems with
boards versus cable/switch problems.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove variables that are set but then never looked at in the ipath
driver.  These cleanups came from David Binderman's list of "set but
never used" warnings from icc.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The PCI Express and Hypertransport chip-specific source files should only
be built when the kernel has the capability of actually compiling them.

This fixes the driver build on, for example, ia64.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Eric's changes to the htirq infrastructure require corresponding
modifications to the ipath HT driver code so that interrupts are still
delivered properly.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Don't attempt to set up the diagpkt device in the module init code.
Instead, wait until a piece of hardware is initialized.  Fixes a
problem when loading the ib_ipath module when no InfiniPath hardware
is present: modprobe would go into the D state and stay there.
Signed-off-by: NRobert Walsh <robert.walsh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Prior to this change, the driver was not able to support a HT and PCIE
card simultaneously present in the same machine.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This gives upper-level protocols a chance to unregister while the device
is still usable.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This allows multiple userspace processes to share a single hardware
context in a master/slave arrangement.  It is backwards binary compatible
with existing userspace.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>