So far BCM47XX can only detect amount of HIGHMEM. It still requires
adding (registering) and well-testing before enabling by default.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7396/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Patch was tested on devices with 64 MiB and 256 MiB of RAM.
It documents every part nicely and drops this hacky part of code:
max = off | ((128 << 20) - 1);
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/6808/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The BCM47xx SoCs have a 8250 serial compatible console at address
0x18000300 and an other at 0x18000400. On most devices 0x18000300 is
wired to some pins on the board, we should use that.
This is the smae for the AI (bcma) and the SB (ssb) bus, this is some
offset on the chip common core.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5889/

bcm47xx only uses the CFE code for early print to a console, but that
is also possible with a early print serial 8250 driver.

The CFE api init causes hangs somewhere in prom_init_cfe() on some
devices like the Buffalo WHR-HP-G54 and the Asus WL-520GU.
This was reported in https://dev.openwrt.org/ticket/4061 and
https://forum.openwrt.org/viewtopic.php?id=17063

This will remove all the CFE handling code from bcm47xx.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5888/

Recently the output of "system type" in  /proc/cpuinfo was changed to
Broadcom BCM4730 (Some sample board), but it is better to just print
the SoC name in the "system type" entry. The board name will be added
in the machine entry later.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5865/

Do not print the constant system type "Broadcom BCM47XX" but print the
name of the actual SoC in use and the detected board.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5839/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The memory size is detected by finding a place where it repeats in
memory. Currently we are just checking when the function prom_init is
seen again, but it is better to check for a bigger part of the memory
to decrease the chance of wrong results.

This should fix a problem we saw in OpenWrt, where the detected
available memory decreed on some devices when doing a soft reboot.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4362Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Ignoring the last page when ddr size is 128M. Cached accesses to last
page is causing the processor to prefetch using address above 128M
stepping out of the ddr address space.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4365Signed-off-by: NJohn Crispin <blogic@openwrt.org>

The previous patch 4a86f2d27733f610e642649aca3e82e86fca9e22 (lmo) rsp.
84a6fcb3 (kernel.org) was wrong.

The BCM47xx architecture maps the ram into a 128MB address space. It
will be spaced there as often as goes into the 128MB. Detection tries to
find the position where the same memory is found. When reading beyond
128MB the processor will throw an exception. If 128MB RAM is installed,
it will not find a memory alias because it tries to read beyond the 128MB
border. Now it just assumes 128MB installed ram if it can not find an
alias.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1508/Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Recent git versions now warn about those and they've always been a bit of
an annoyance.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Ignoring the last page when ddr size is 128M. Cached accesses to last page
is causing the processor to prefetch using address above 128M stepping out
of the DDR address space.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/981/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The MIPS-specific macro CL_SIZE is merely aliasing the macro
COMMAND_LINE_SIZE. Other architectures use the latter; also,
COMMAND_LINE_SIZE is documented in kernel-parameters.txt, so
let's use it, and remove the alias.
Signed-off-by: NDmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Since commit 22242681 ("MIPS: Extend
COMMAND_LINE_SIZE"), CL_SIZE is 4096 and local array variables with this
size will cause an build failure with default CONFIG_FRAME_WARN settings.

Although current users of such array variables are all early bootstrap
code and not likely to cause real stack overflow (thread_info corruption),
it is preferable to  to declare these arrays static with __initdata.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add CFE support to the BCM47XX code.  That includes querying CFE environment
variables as well as using CFE to print messages before the serial port is
initialized (early printk).
Signed-off-by: NAurelien Jarno <aurel32@farad.aurel32.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Note that the BCM4710 does not support the wait instruction, this
is not a mistake in the code.
    
It originally comes from the OpenWrt patches.
    
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Florian Schirmer <jolt@tuxbox.org>
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Patch to add PCI support for the PMC-Sierra MSP71xx devices.
Signed-off-by: NMarc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Patch to add core platform support for the PMC-Sierra MSP71xx devices.
Signed-off-by: NMarc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This is to break the code of people who think they are supposed to scribble
into the pci device structure - it's off limits.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Cleaned up a to of warnings in dbdma.c.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!