We should not do temperature compensation on devices without
EXTERNAL_TX_ALC bit set (called DynamicTxAgcControl on vendor driver).
Such devices can have totally bogus TSSI parameters on the EEPROM,
but still threaded by us as valid and result doing wrong TX power
calculations.

This fix inability to connect to AP on slightly longer distance on
some Ralink chips/devices.
Reported-and-tested-by: NFabien ADAM <id2ndr@crocobox.org>
Cc: stable@vger.kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A lot of files contain reference to my old e-mail address.
Now I'm going not to read mail from it anymore, so update it
with my current address everywhere.
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix to return -ENOMEM in the memory alloc error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes multiple locations where a little endian host is assumed during
ser/des of messages sent to/received from the chip.
Signed-off-by: NTobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to call ath_txq_unlock_complete() in the
TX poll routine - frame completion is not done here,
so use ath_txq_unlock().
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The PCIE Workaround register (AR_WA/0x4004) is used to handle
various hardware quirks. For AR9002 chips, AR_WA_D3_L1_DISABLE
is used to prevent the HW from automatically entering L1 state
when D3 is enforced.

AR_WA_D3_L1_DISABLE has to be enabled for a few AR9280 based
cards, mark them based on their PCI subdevice/subvendor IDs
and enforce it in ar9002_hw_configpcipowersave().
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Avoid processing garbage data by NULL terminating the strings.
Signed-off-by: NDjalal Harouni <tixxdz@opendz.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the L1 entrance latency is not calibrated properly
in the EEPROM in WB222 boards, there could be problems
in connectivity. Check and correct the calibrated value
if it doesn't match the optimal value for WB222, 4us.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for dropping gratuitous ARP frames which is
requirement for WFA Hotspot2.0.

Hotspot2.0 capability is enabled in driver if extended capabilities
IE from BSS descriptor has 11u interworking enabled.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

EXT_CAPAB_IE format involves IEEE header followed by bytestream of
capabilities. Current structure has incorrect member u8 for data;
fix it by defining it as u8[0].
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have usb_deregister() call in our rmmod routine. deauth,
shutdown etc. commands will be sent to FW later when bus
driver calls disconnect handler.

This mechanism works fine with SDIO and PCIe interfaces, but
there is an issue with USB.

USB bus driver returns all URBs submitted for receiving data
and command response immediately after usb_deregister() with
failure status. Hence we don't send deauth, shutdown etc.
command to firmware.

The problem is fixed by moving code from disconnect handler to
rmmod routine for USB interface.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tell the PCIe host core when the wifi is activated.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This enables or disables power saving on the PCIe bus when the wifi is
in operation or not.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is not called any more, do not export it.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

replace the calls to bcma_core_pci_extend_L1timer() by calls to the
newly introduced bcma_core_pci_ip() and bcma_core_pci_down()
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wifi driver should tell the PCIe core that it is now in operation
so that some workarounds can be applied and the power state is changed.
This should replace the call to bcma_core_pci_extend_L1timer by the
brcmsmac driver.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This PCIe controller does not support a max read request size above 128
bytes. The sold card I tested this controller with used 128 as default
value, but some new routers are sold with BCM4331 chips, which have a
default max read request size of 512. This device fails at the first
DMA reqeust whch is bigger than 126 bytes.

This patch changes the max read request size to 128 for every device on
the PCIe link.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The values written into the BCN_OFFSET[01] registers are
hardcoded in the rt2800_init_register function.

Add a macro and a helper function to derive these values
directly from the base address of a given beacon, and use
the new function instead of the hardcoded numbers.

The patch contains no functional changes. The programmed
register values are the same before and after the patch.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The HW_BEACON_BASE() macro returns the base address
of a given beacon, however the returned values are
not usable on all chipsets. On devices which have
selectable shared memory parts, some beacon may be
located in the high part of the shared memory.

Instead of extending the already complicated macro,
add a new helper function and use that to get the
base address of a given beacon.

The actual patch contains no functional changes, the
helper function will be extended in a further patch
to handle different chipsets' requirements.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch completes the changes needed for supporting the
iPA variant cards of the BCM4313 wireless chipset.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When changing channels the TSSI based power control needs to be
reinitialized.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A number of additional phy registers needs to be programmed when
using TSSI-based power control.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rework the code path in lcnphy tbl_init() for switch control
table programming. This also takes the iPA BT-combo card into
account.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For lcnphy revision 1 or when hardware supports i/q calibration the
function wlc_lcnphy_set_txpwr_by_index() was called twice.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The baseband multiplier must be zero during TSSI idle estimation
and restored afterwards.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The gain level control for the test tone has been changed. This
calbration test tone is used to determine the i/q compensation.
The i/q calibration routine has been reworked to accomodate this.

Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the transmit gain table for bcm4313 chip family.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For debug purposes it is good to have the phy and radio information
available in the log. Only logged when driver is built when BRCMDBG
or BRCM_TRACING kconfig are set.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch converts all sizeof(x)/sizeof(x[0]) instances to
ARRAY_SIZE macro in phytbl_lcn.c. The patch was made using
spatch with ARRAY_SIZE.cocci (see [1]).

[1] https://github.com/coccinelle/coccinelle/tree/master/demos/janitorings

Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function wlc_lcnphy_load_tx_gain_table() has a target PA
gain specified for the iPA variant of the bcm4313. This gain
value is reduced to avoid PA distortion. The if-statement is
removed because it was rather redundant in the first place.
Please note that this patch does not provide full iPA support.

Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cleaning up some code fragments reducing indentation and uncluttering
some lines. Apart from whitespace there are no actual code changes
made.

Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a AR9485/WB225 based card.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bug 60747 - 1286:2044 [Microsoft Surface Pro]
    Marvell 88W8797 wifi show 3 interface under network
https://bugzilla.kernel.org/show_bug.cgi?id=60747

This issue was also reported previously by OLPC and some folks from
the community.

There are 3 network interfaces with different types being created
when mwifiex driver is loaded:

1. mlan0 (infra. STA)
2. uap0 (AP)
3. p2p0 (P2P_CLIENT)

The Network Manager attempts to use all 3 interfaces above without
filtering the managed interface type. As the result, 3 identical
interfaces are displayed under network manager. If user happens to
click on an entry under which its interface is uap0 or p2p0, the
association will fail.

Work around it by removing the creation of AP and P2P interfaces
at driver loading time. These interfaces can be added with 'iw' or
other applications manually when they are needed.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This improves RX diversity and performance for AR9485.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Along with other chipsets, the Ralink driver uses the
frequency adjustment code for RF3053 as well. Remove
the bogus place-holder comment from the RF3053 specific
channel configuration function and call the frequency
adjustment function instead

Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RT3593_ChipSwitchChannel function in chips/rt3593.c
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the rt2800_adjust_freq_offset function before
the channel configuration functions to make it usable
from those without a forward declaration.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver, the RFCSR17 register can't be programmed in
one step on devices which are using the frequency
offset adjustment code.

Update the code to use step-by-step adjustment.

Reference:
  RT30xxWriteRFRegister function in common/rt_rf.c
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to the Ralink driver, there is an MCU
command which can be used to send the frequency
offset value directly to the USB device without
going through the RFCSR writing sequence.

Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RTMPAdjustFrequencyOffset function in common/rt_rf.c
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>