The DSA layer should no longer assume the switch is connected to an
MDIO bus. As a result, we cannot use the address on the MDIO bus when
forming the name of the switches internal MDIO bus for its builtin and
possibly external PHYs. The switch index is sufficient to make the
name unique, so drop the MDIO address.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lock debugging shows that there is a possible circular lock in the PPU
work code. Switch the lock order of smi_mutex and ppu_mutex to fix this.

Here's the full trace:

    [    4.341325] ======================================================
    [    4.347519] [ INFO: possible circular locking dependency detected ]
    [    4.353800] 4.6.0 #4 Not tainted
    [    4.357039] -------------------------------------------------------
    [    4.363315] kworker/0:1/328 is trying to acquire lock:
    [    4.368463]  (&ps->smi_mutex){+.+.+.}, at: [<8049c758>] mv88e6xxx_reg_read+0x30/0x54
    [    4.376313]
    [    4.376313] but task is already holding lock:
    [    4.382160]  (&ps->ppu_mutex){+.+...}, at: [<8049cac0>] mv88e6xxx_ppu_reenable_work+0x28/0xd4
    [    4.390772]
    [    4.390772] which lock already depends on the new lock.
    [    4.390772]
    [    4.398963]
    [    4.398963] the existing dependency chain (in reverse order) is:
    [    4.406461]
    [    4.406461] -> #1 (&ps->ppu_mutex){+.+...}:
    [    4.410897]        [<806d86bc>] mutex_lock_nested+0x54/0x360
    [    4.416606]        [<8049a800>] mv88e6xxx_ppu_access_get+0x28/0x100
    [    4.422906]        [<8049b778>] mv88e6xxx_phy_read+0x90/0xdc
    [    4.428599]        [<806a4534>] dsa_slave_phy_read+0x3c/0x40
    [    4.434300]        [<804943ec>] mdiobus_read+0x68/0x80
    [    4.439481]        [<804939d4>] get_phy_device+0x58/0x1d8
    [    4.444914]        [<80493ed0>] mdiobus_scan+0x24/0xf4
    [    4.450078]        [<8049409c>] __mdiobus_register+0xfc/0x1ac
    [    4.455857]        [<806a40b0>] dsa_probe+0x860/0xca8
    [    4.460934]        [<8043246c>] platform_drv_probe+0x5c/0xc0
    [    4.466627]        [<804305a0>] driver_probe_device+0x118/0x450
    [    4.472589]        [<80430b00>] __device_attach_driver+0xac/0x128
    [    4.478724]        [<8042e350>] bus_for_each_drv+0x74/0xa8
    [    4.484235]        [<804302d8>] __device_attach+0xc4/0x154
    [    4.489755]        [<80430cec>] device_initial_probe+0x1c/0x20
    [    4.495612]        [<8042f620>] bus_probe_device+0x98/0xa0
    [    4.501123]        [<8042fbd0>] deferred_probe_work_func+0x4c/0xd4
    [    4.507328]        [<8013a794>] process_one_work+0x1a8/0x604
    [    4.513030]        [<8013ac54>] worker_thread+0x64/0x528
    [    4.518367]        [<801409e8>] kthread+0xec/0x100
    [    4.523201]        [<80108f30>] ret_from_fork+0x14/0x24
    [    4.528462]
    [    4.528462] -> #0 (&ps->smi_mutex){+.+.+.}:
    [    4.532895]        [<8015ad5c>] lock_acquire+0xb4/0x1dc
    [    4.538154]        [<806d86bc>] mutex_lock_nested+0x54/0x360
    [    4.543856]        [<8049c758>] mv88e6xxx_reg_read+0x30/0x54
    [    4.549549]        [<8049cad8>] mv88e6xxx_ppu_reenable_work+0x40/0xd4
    [    4.556022]        [<8013a794>] process_one_work+0x1a8/0x604
    [    4.561707]        [<8013ac54>] worker_thread+0x64/0x528
    [    4.567053]        [<801409e8>] kthread+0xec/0x100
    [    4.571878]        [<80108f30>] ret_from_fork+0x14/0x24
    [    4.577139]
    [    4.577139] other info that might help us debug this:
    [    4.577139]
    [    4.585159]  Possible unsafe locking scenario:
    [    4.585159]
    [    4.591093]        CPU0                    CPU1
    [    4.595631]        ----                    ----
    [    4.600169]   lock(&ps->ppu_mutex);
    [    4.603693]                                lock(&ps->smi_mutex);
    [    4.609742]                                lock(&ps->ppu_mutex);
    [    4.615790]   lock(&ps->smi_mutex);
    [    4.619314]
    [    4.619314]  *** DEADLOCK ***
    [    4.619314]
    [    4.625256] 3 locks held by kworker/0:1/328:
    [    4.629537]  #0:  ("events"){.+.+..}, at: [<8013a704>] process_one_work+0x118/0x604
    [    4.637288]  #1:  ((&ps->ppu_work)){+.+...}, at: [<8013a704>] process_one_work+0x118/0x604
    [    4.645653]  #2:  (&ps->ppu_mutex){+.+...}, at: [<8049cac0>] mv88e6xxx_ppu_reenable_work+0x28/0xd4
    [    4.654714]
    [    4.654714] stack backtrace:
    [    4.659098] CPU: 0 PID: 328 Comm: kworker/0:1 Not tainted 4.6.0 #4
    [    4.665286] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
    [    4.671748] Workqueue: events mv88e6xxx_ppu_reenable_work
    [    4.677174] Backtrace:
    [    4.679674] [<8010d354>] (dump_backtrace) from [<8010d5a0>] (show_stack+0x20/0x24)
    [    4.687252]  r6:80fb3c88 r5:80fb3c88 r4:80fb4728 r3:00000002
    [    4.693003] [<8010d580>] (show_stack) from [<803b45e8>] (dump_stack+0x24/0x28)
    [    4.700246] [<803b45c4>] (dump_stack) from [<80157398>] (print_circular_bug+0x208/0x32c)
    [    4.708361] [<80157190>] (print_circular_bug) from [<8015a630>] (__lock_acquire+0x185c/0x1b80)
    [    4.716982]  r10:9ec22a00 r9:00000060 r8:8164b6bc r7:00000040 r6:00000003 r5:8163a5b4
    [    4.724905]  r4:00000003 r3:9ec22de8
    [    4.728537] [<80158dd4>] (__lock_acquire) from [<8015ad5c>] (lock_acquire+0xb4/0x1dc)
    [    4.736378]  r10:60000013 r9:00000000 r8:00000000 r7:00000000 r6:9e5e9c50 r5:80e618e0
    [    4.744301]  r4:00000000
    [    4.746879] [<8015aca8>] (lock_acquire) from [<806d86bc>] (mutex_lock_nested+0x54/0x360)
    [    4.754976]  r10:9e5e9c1c r9:80e616c4 r8:9f685ea0 r7:0000001b r6:9ec22a00 r5:8163a5b4
    [    4.762899]  r4:9e5e9c1c
    [    4.765477] [<806d8668>] (mutex_lock_nested) from [<8049c758>] (mv88e6xxx_reg_read+0x30/0x54)
    [    4.774008]  r10:80e60c5b r9:80e616c4 r8:9f685ea0 r7:0000001b r6:00000004 r5:9e5e9c10
    [    4.781930]  r4:9e5e9c1c
    [    4.784507] [<8049c728>] (mv88e6xxx_reg_read) from [<8049cad8>] (mv88e6xxx_ppu_reenable_work+0x40/0xd4)
    [    4.793907]  r7:9ffd5400 r6:9e5e9c68 r5:9e5e9cb0 r4:9e5e9c10
    [    4.799659] [<8049ca98>] (mv88e6xxx_ppu_reenable_work) from [<8013a794>] (process_one_work+0x1a8/0x604)
    [    4.809059]  r9:80e616c4 r8:9f685ea0 r7:9ffd5400 r6:80e0a1c8 r5:9f5f2e80 r4:9e5e9cb0
    [    4.816910] [<8013a5ec>] (process_one_work) from [<8013ac54>] (worker_thread+0x64/0x528)
    [    4.825010]  r10:9f5f2e80 r9:00000008 r8:80e0dc80 r7:80e0a1fc r6:80e0a1c8 r5:9f5f2e98
    [    4.832933]  r4:80e0a1c8
    [    4.835510] [<8013abf0>] (worker_thread) from [<801409e8>] (kthread+0xec/0x100)
    [    4.842827]  r10:00000000 r9:00000000 r8:00000000 r7:8013abf0 r6:9f5f2e80 r5:9ec15740
    [    4.850749]  r4:00000000
    [    4.853327] [<801408fc>] (kthread) from [<80108f30>] (ret_from_fork+0x14/0x24)
    [    4.860557]  r7:00000000 r6:00000000 r5:801408fc r4:9ec15740
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new binding does not make use of dsa_chip_data, a.k.a cd.  When
retrieving the size of the EEPROM attached to a switch, don't assume
there is a cd attached to the switch structure.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

size_t objects should be printed with %Z printf format.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit a91eb52a ("qed: Revisit chain implementation") contains an
incorrect implementation for BE platforms, as device's regpairs containing
addresses are LE and they're not converted correctly when read back.
In addition, it raises a compilation warning for 32-bit platforms where
dma_addr_t is a 32-bit variable.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed: RocE & iSCSI infrastructure

We plan on sending 2 new protocol drivers in the imminent future -
both our RoCE [qedr] and iSCSI [qedi] drivers. As both submissions
would be rather massive and in order to avoid collisions between them,
the common infrastructure on the qed side was prepared as an independent
patch-series to be sent ahead of those 2 submissions.

This patch series introduces in QED 2 new 'ids' - one for iscsi and
one for roce. It then goes and adds logic required for configuring
said protocols in HW. Notice it *doesn't* actually add any client using
said ids, but rather only the infrastructure to allow their later usage.

What this patch doesn't contain is the slowpath protocol-configuration
toward the firmware. I.e., it contains register-setting logic, memory
allocations, etc., but not actual flow-related configuration specific
to the protocl. Those would be sent as part of the protocol driver
submissions.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RoCE and iSCSI would require some added/changed hw configuration in order
to properly run; The biggest single change being the requirement of
allocating and mapping host memory for several HW blocks that aren't being
used by qede [SRC, QM, TM, etc.].

In addition, whereas qede is only using context memory for HW blocks, the
new protocol would also require task memories to be added.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds in the ecore 2 new personalities in addition to
QED_PCI_ETH - QED_PCI_ISCSI and QED_PCI_ETH_ROCE.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the qed portion of the RoCE & iSCSI firmware HSI,
as well as adding several new common HSI files which would be required
by both qed and qed* protocols.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RoCE driver is going to need a 32-bit chain [current chain implementation
for qed* currently supports only 16-bit producer/consumer chains].

This patch adds said support, as well as doing other slight tweaks and
modifications to qed's chain API.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no reason in this lock. At least for now.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the more common kernel logging style and reduce object size.

The logging message prefix changes from a mixture of
"RxRPC:" and "RXRPC:" to "af_rxrpc: ".

$ size net/rxrpc/built-in.o*
   text	   data	    bss	    dec	    hex	filename
  64172	   1972	   8304	  74448	  122d0	net/rxrpc/built-in.o.new
  67512	   1972	   8304	  77788	  12fdc	net/rxrpc/built-in.o.old

Miscellanea:

o Consolidate the ASSERT macros to use a single pr_err call with
  decimal and hexadecimal output and a stringified #OP argument
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added a condition to avoid vlan devices with same MAC registering
as VF.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marcelo Ricardo Leitner says:

====================
sctp: Add GSO support

This patchset adds sctp GSO support.

Performance tests indicates that increases throughput by 10% if using
bigger chunk sizes, specially if bigger than MTU. For small chunks, it
doesn't help much if not using heavy firewall rules.

For small chunks it will probably be of more use once we get something
like MSG_MORE as David Laight had suggested.

overall changes:
v1->v2:
Added support for receiving GSO frames on SCTP stack, as requested by
Dave Miller.

v2->v3:
Consider sctphdr size in skb_gso_transport_seglen()
rebased due to 5c7cdf33 ("gso: Remove arbitrary checks for
unsupported GSO")
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is useful for debugging packet sizes.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SCTP has this pecualiarity that its packets cannot be just segmented to
(P)MTU. Its chunks must be contained in IP segments, padding respected.
So we can't just generate a big skb, set gso_size to the fragmentation
point and deliver it to IP layer.

This patch takes a different approach. SCTP will now build a skb as it
would be if it was received using GRO. That is, there will be a cover
skb with protocol headers and children ones containing the actual
segments, already segmented to a way that respects SCTP RFCs.

With that, we can tell skb_segment() to just split based on frag_list,
trusting its sizes are already in accordance.

This way SCTP can benefit from GSO and instead of passing several
packets through the stack, it can pass a single large packet.

v2:
- Added support for receiving GSO frames, as requested by Dave Miller.
- Clear skb->cb if packet is GSO (otherwise it's not used by SCTP)
- Added heuristics similar to what we have in TCP for not generating
  single GSO packets that fills cwnd.
v3:
- consider sctphdr size in skb_gso_transport_seglen()
- rebased due to 5c7cdf33 ("gso: Remove arbitrary checks for
  unsupported GSO")
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is a preparation for the GSO one. In order to successfully
handle GSO packets on rx path we must not call skb_linearize, otherwise
it defeats any gain GSO may have had.

This patch thus delays as much as possible the call to skb_linearize,
leaving it to sctp_inq_pop() moment. For that the sanity checks
performed now know how to deal with fragments.

One positive side-effect of this is that if the socket is backlogged it
will have the chance of doing it on backlog processing instead of
during softirq.

With this move, it's evident that a check for non-linearity in
sctp_inq_pop was ineffective and is now removed. Note that a similar
check is performed a bit below this one.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb_gso_network_seglen is not enough for checking fragment sizes if
skb is using GSO_BY_FRAGS as we have to check frag per frag.

This patch introduces skb_gso_validate_mtu, based on the former, which
will wrap the use case inside it as all calls to skb_gso_network_seglen
were to validate if it fits on a given TMU, and improve the check.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows segmenting a skb based on its frags sizes instead of
based on a fixed value.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sctp GSO requires it and sctp can be compiled as a module, so we need to
export this function.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NETIF_F_GSO_SOFTWARE was defined to list all GSO software types, so lets
make use of it in loopback code. Note that veth/vxlan/others already
uses it.

Within this patch series, this patch causes lo to pick up SCTP GSO feature
automatically (as it's added to NETIF_F_GSO_SOFTWARE) and thus avoiding
segmentation if possible.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_workqueue replaces deprecated create_workqueue().

The workqueue adapter->txrx_wq has workitem
&adapter->raise_intr_rxdata_task per adapter. Extended Socket Network
Device is shared memory based, so someone's transmission denotes other's
reception.  raise_intr_rxdata_task raises interruption of receivers from
the sender in order to notify receivers.

The workqueue adapter->control_wq has workitem
&adapter->interrupt_watch_task per adapter. interrupt_watch_task is used
to prevent delay of interrupts.

Dedicated workqueues have been used in both cases since the workitems
on the workqueues are involved in normal device operation and require
forward progress under memory pressure.

max_active has been set to 0 since there is no need for throttling
the number of active work items.

Since network devices  may be used for memory reclaim,
WQ_MEM_RECLAIM has been set to guarantee forward progress.
Signed-off-by: NBhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The New QED firmware contains several fixes, including:
  - Wrong classification of packets in 4-port devices.
  - Anti-spoof interoperability with encapsulated packets.
  - Tx-switching of encapsulated packets.
It also slightly improves Tx performance of the device.

In addition, this firmware contains the necessary logic for
supporting iscsi & rdma, for which we plan on pushing protocol
drivers in the imminent future.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VRF device exists to define L3 domains and guide FIB lookups. As
such its operstate is not relevant. Seeing 'state UNKNOWN' in the
output of 'ip link show' can be confusing, so set operstate at link
create.

Similarly, the MTU for a VRF device is not used; any fragmentation
of the payload is done on the output path based on the real egress
device. An MTU of 1500 on the VRF device while enslaved devices
have a higher MTU can lead to confusion. Since the VRF MTU is not
relevant set to 64k similar to what is done for loopback.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set name_assign_type of internal port to NET_NAME_USER.
Signed-off-by: NZhang Shengju <zhangshengju@cmss.chinamobile.com>
Acked-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_workqueue replaces deprecated create_workqueue().

A dedicated workqueue has been used since the workitems are involved
in normal device operation. Workitems &priv->rx_work and &priv->tx_work,
map to w5100_rx_work and w5100_tx_work respectively and are involved in
receiving and transmitting packets. Forward progress under
memory pressure is a requirement here.

create_workqueue has been replaced with alloc_workqueue with max_active
as 0 since there is no need for throttling the number of active work
items.

Since the driver may be used in memory reclaim path,
WQ_MEM_RECLAIM has been set to guarantee forward progress.

flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty. Hence the call to flush_workqueue() has been dropped.
Signed-off-by: NBhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Writing a non-zero value to the manual PAUSE frame register (MPR) starts
the transmission of a PAUSE frame.
A PAUSE frame is sent in ravb_emac_init(), but it is not expected behavior.
Signed-off-by: NMasaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: NKazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's not much point, except compile test, enabling the stmmac
platform drivers unless their actual SoC is enabled. They're not
useful without it.
Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Herbert Xu says:

====================
macvlan: Avoid unnecessary multicast cloning

This patch tries to improve macvlan multicast performance by
maintaining a filter hash at the macvlan_port level so that we
can quickly determine whether a given packet is needed or not.

It is preceded by a patch that fixes a potential use-after-free
bug that I discovered while looking over this.

v2 fixed a bug where promiscuous/allmulti settings weren't handled
correctly.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we always queue a multicast packet for further processing,
even if none of the macvlan devices are subscribed to the address.

This patch optimises this by adding a global multicast filter for
a macvlan_port.

Note that this patch doesn't handle the broadcast addresses of the
individual macvlan devices correctly, if they are not all identical
to vlan->lowerdev.  However, this is already broken because there
is no mechanism in place to update the individual multicast filters
when you change the broadcast address.

If someone cares enough they should fix this by collecting all
broadcast addresses for a macvlan as we do for multicast and unicast.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we postpone a broadcast packet we save the source port in
the skb if it is local.  However, the source port can disappear
before we get a chance to process the packet.

This patch fixes this by holding a ref count on the netdev.

It also delays the skb->cb modification until after we allocate
the new skb as you should not modify shared skbs.

Fixes: 412ca155 ("macvlan: Move broadcasts into a work queue")
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit e6afc8ac ("udp: remove headers from UDP packets before
queueing"), udp_csum_pull_header() helper was added but missed fact
that CHECKSUM_UNNECESSARY packets were now converted to CHECKSUM_NONE
and skb->csum_valid was set to 1 for them.

Since csum_partial() is quite expensive, even for 8-byte area, it is
worth adding a test.

We also can use skb->data instead of udp_hdr() as we are pulling
UDP headers, as it is sightly faster.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use SET_RUNTIME_PM_OPS macro instead of assigning a member of
dev_pm_ops directly.
Signed-off-by: NKazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The H/W manual recommends B'10 or B'11 in a value of the separation
filtering select bits in the receive configuration register (RCR.ESF).
When B'10 is set, frames from non-matching streams are discarded.
When B'11 is set, frames from non-matching streams are processed in
reception queue 0 (best effort).
This patch sets B'11 in ESF.

[ykaneko0929@gmail.com: revised this commit message]
Signed-off-by: NMasaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: NKazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix negative error code usage in ATM layer, from Stefan Hajnoczi.

 2) If CONFIG_SYSCTL is disabled, the default TTL is not initialized
    properly.  From Ezequiel Garcia.

 3) Missing spinlock init in mvneta driver, from Gregory CLEMENT.

 4) Missing unlocks in hwmb error paths, also from Gregory CLEMENT.

 5) Fix deadlock on team->lock when propagating features, from Ivan
    Vecera.

 6) Work around buffer offset hw bug in alx chips, from Feng Tang.

 7) Fix double listing of SCTP entries in sctp_diag dumps, from Xin
    Long.

 8) Various statistics bug fixes in mlx4 from Eric Dumazet.

 9) Fix some randconfig build errors wrt fou ipv6 from Arnd Bergmann.

10) All of l2tp was namespace aware, but the ipv6 support code was not
    doing so.  From Shmulik Ladkani.

11) Handle on-stack hrtimers properly in pktgen, from Guenter Roeck.

12) Propagate MAC changes properly through VLAN devices, from Mike
    Manning.

13) Fix memory leak in bnx2x_init_one(), from Vitaly Kuznetsov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
  sfc: Track RPS flow IDs per channel instead of per function
  usbnet: smsc95xx: fix link detection for disabled autonegotiation
  virtio_net: fix virtnet_open and virtnet_probe competing for try_fill_recv
  bnx2x: avoid leaking memory on bnx2x_init_one() failures
  fou: fix IPv6 Kconfig options
  openvswitch: update checksum in {push,pop}_mpls
  sctp: sctp_diag should dump sctp socket type
  net: fec: update dirty_tx even if no skb
  vlan: Propagate MAC address to VLANs
  atm: iphase: off by one in rx_pkt()
  atm: firestream: add more reserved strings
  vxlan: Accept user specified MTU value when create new vxlan link
  net: pktgen: Call destroy_hrtimer_on_stack()
  timer: Export destroy_hrtimer_on_stack()
  net: l2tp: Make l2tp_ip6 namespace aware
  Documentation: ip-sysctl.txt: clarify secure_redirects
  sfc: use flow dissector helpers for aRFS
  ieee802154: fix logic error in ieee802154_llsec_parse_dev_addr
  net: nps_enet: Disable interrupts before napi reschedule
  net/lapb: tuse %*ph to dump buffers
  ...

Pull sparc fixes from David Miller:
 "sparc64 mmu context allocation and trap return bug fixes"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Fix return from trap window fill crashes.
  sparc: Harden signal return frame checks.
  sparc64: Take ctx_alloc_lock properly in hugetlb_setup().

Otherwise we get confused when two flows on different channels get the
 same flow ID.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To detect link status up/down for connections where autonegotiation is
explicitly disabled, we don't get an irq but need to poll the status
register for link up/down detection.
This patch adds a workqueue to poll for link status.
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function virtnet_open() and virtnet_probe(), func try_fill_recv() may
be executed at the same time. VQ in virtqueue_add() has not been protected
well and BUG_ON will be triggered when virito_net.ko being removed.
Signed-off-by: NYunjian Wang <wangyunjian@huawei.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>