crash_dump: export is_kdump_kernel to modules, consolidate elfcorehdr_addr, setup_elfcorehdr and saved_max_pfn

The Xen PV drivers in a crashed HVM guest can not connect to the dom0
backend drivers because both frontend and backend drivers are still in
connected state.  To run the connection reset function only in case of a
crashdump, the is_kdump_kernel() function needs to be available for the PV
driver modules.

Consolidate elfcorehdr_addr, setup_elfcorehdr and saved_max_pfn into
kernel/crash_dump.c Also export elfcorehdr_addr to make is_kdump_kernel()
usable for modules.

Leave 'elfcorehdr' as early_param().  This changes powerpc from __setup()
to early_param().  It adds an address range check from x86 also on ia64
and powerpc.

[akpm@linux-foundation.org: additional #includes]
[akpm@linux-foundation.org: remove elfcorehdr_addr export]
[akpm@linux-foundation.org: fix for Tejun's mm/nobootmem.c changes]
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There is no user now.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

minix bit operations are only used by minix filesystem and useless by
other modules.  Because byte order of inode and block bitmaps is different
on each architecture like below:

m68k:
	big-endian 16bit indexed bitmaps

h8300, microblaze, s390, sparc, m68knommu:
	big-endian 32 or 64bit indexed bitmaps

m32r, mips, sh, xtensa:
	big-endian 32 or 64bit indexed bitmaps for big-endian mode
	little-endian bitmaps for little-endian mode

Others:
	little-endian bitmaps

In order to move minix bit operations from asm/bitops.h to architecture
independent code in minix filesystem, this provides two config options.

CONFIG_MINIX_FS_BIG_ENDIAN_16BIT_INDEXED is only selected by m68k.
CONFIG_MINIX_FS_NATIVE_ENDIAN is selected by the architectures which use
native byte order bitmaps (h8300, microblaze, s390, sparc, m68knommu,
m32r, mips, sh, xtensa).  The architectures which always use little-endian
bitmaps do not select these options.

Finally, we can remove minix bit operations from asm/bitops.h for all
architectures.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As the result of conversions, there are no users of ext2 non-atomic bit
operations except for ext2 filesystem itself.  Now we can put them into
architecture independent code in ext2 filesystem, and remove from
asm/bitops.h for all architectures.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Introduce little-endian bit operations by renaming native ext2 bit
operations.  The ext2 and minix bit operations are kept as wrapper macros
using little-endian bit operations to maintain bisectability until the
conversions are finished.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.

Note that mfd-core no longer makes a copy of platform_data, but the
mc13xxx-core driver creates the pdata structures on the stack.  In
order to get around that, the various ARM mach types that set the
pdata have been changed to hold the variable in static (global) memory.
Also note that __initdata references in aforementioned pdata structs
have been dropped.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

In Blaze and Panda, 32KHz clock - CLK32KG to WLAN is supplied
from Phoenix TWL6030.
Add CLK32KG platform data to blaze and omap4panda board file.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

All architectures can use the common dma_addr_t typedef now. We can
remove the arch specific dma_addr_t.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change LED triggers to mimic WinMobile behavior:
red blinking when battery is charging,
orange solid when battery is charged.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch moves the platform data definition from
arch/arm/plat-pxa/include/plat/i2c.h to include/linux/i2c/pxa-i2c.h so
it can be accessed from x86 the same way as on ARM.

This change should make no functional change to the PXA code. The move
is verified by building the following defconfigs:
  cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
  imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
  raumfeld_defconfig magician_defconfig mmp2_defconfig pxa168_defconfig
  pxa910_defconfig
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add .gpio_set_blink callback to support HW blinking
available on RX1950
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

s3c_adc_battery uses LEDs to indicate charging process,
retain LEDs state in suspend, otherwise user have no information if PDA
battery is charging after he put it to suspend.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Current implementation of lcd_power_set is not reliable, sometimes
it does not enable LCD at all.
Mimic WinCE behavior to fix this issue.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add battery monitoring/charging support via pda_power and
s3c_adc_battery drivers
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

We can use generic leds-gpio driver, as latch api was converted
to gpiolib.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

It was broken by removal of rfkill_set_led_trigger_name function,
and now compiler complains about implicit declaration.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add buttons definition for H1940.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

As many entries have never been submitted to mainline, there's no point
them existing in this file.  So remove the entries which aren't relevant
for mainline.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The current Versatile Express BSP defines the MACHINE_START macro
in the core tile code.

This patch moves this into the generic board code and introduces a
method for determining the current tile at runtime, allowing the
Kernel to have support for multiple tiles compiled in. Tile-specific
functions are executed via a descriptor struct containing the correct
implementations for the current tile.
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Adding DVI support to OMAP4 PandaBoard.

PandaBoard uses TFP410 DVI Framer chip
http://focus.ti.com/lit/ds/symlink/tfp410.pdf

The TFP410 gets its power enable and display data over GPIO lines muxed
in from OMAP4430. PandaBoard supports other LCD displays through
expansion
connectors, following board rework. This will disable the DVI interface.
However, the existing mux settings remain the same

PandaBoard additionally supports display over HDMI interface. It is
mutually exclusive to display over DVI. Hence the mux settings need to
be
configured seperately, as and when HDMI is enabled

Also, I2C3 bus used for reading EDID data from DVI Monitors is
registered here. Since the design is similar to BeagleBoard, the code
for the same is taken from the kernel.org commit e3333f48
(omap: Adding beagle i2c eeprom driver to read EDID)
Reviewed-by: NManjunath G Kondaiah <manjugk@ti.com>
Reviewed-by: NAnand Gadiyar <gadiyar@ti.com>
Reviewed-by: NNishanth Menon <nm@ti.com>
Reviewed-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NRaghuveer Murthy <raghuveer.murthy@ti.com>
[tomi.valkeinen@ti.com: fixed conflicts with HDMI]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Tested-by: NMarc Reilly <marc@cpdesign.com.au>
Tested-by: NEric Benard <eric@eukrea.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Tested-by: NMarc Reilly <marc@cpdesign.com.au>
Tested-by: NEric Benard <eric@eukrea.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Replace EXTRA_CFLAGS with ccflags-y and EXTRA_AFLAGS with asflags-y.
Signed-off-by: Nmatt mooney <mfm@muteddisk.com>
Acked-by: NWANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: NMichal Marek <mmarek@suse.cz>

None of the existing cpufreq drivers uses the second argument of
its .suspend() callback (which isn't useful anyway), so remove it.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NDave Jones <davej@redhat.com>

Adding  board file structure for display which adds the display
structure with HDMI as the default driver when the display init
is called.
HDMI GPIO configurations are also done in this file.
Signed-off-by: NMythri P K <mythripk@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Adding  board file structure for display which adds the display
structure with HDMI as the default driver when the display init
is called.
HDMI GPIO configurations are also done in this file.
Signed-off-by: NMythri P K <mythripk@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Adding display type HDMI in dss_features, overlay and the manager so that
HDMI type of display will be recognized.
Signed-off-by: NMythri P K <mythripk@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Initialize the PMIC voltage regulators and provide the supply map for
PCI-e clock supply. The rest of the supplies should be added together
with the drivers that use them.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

* Enable TPS6586x PMIC driver
* Enable RealTek 8169 used on TrimSlice
* Allow booting with root on NFS
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NOlof Johansson <olof@lixom.net>

On Harmony board PCI-e subsystem can be enabled only after certain
voltage regulators are on. One of the regulators is an internal
regulator on the PMIC and another one is controlled by a PMIC GPIO.
Addition of the voltage control to the Harmony PCI-e initialization
allows booting of kernel with CONFIG_TEGRA_PCI even if the PMIC driver
is not loaded. In this case the PCI-e initialization will fail
gracefully intead of hanging the system.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This adds the mmc host driver for Freescale MXS-based SoC i.MX23/28.
The driver calls into mxs-dma via generic dmaengine api for both pio
and data transfer.

Thanks Chris Ball for the indentation patch.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The MUSB driver doesn't see its platform device on DM644x EVM board anymore
since commit 73b089b0 (usb: musb: split davinci
to its own platform_driver) because the new probe is called as subsys_initcall()
now, and the device is registered later than that by the board code.  Move the
registration to davinci_evm_init() -- it's safe to do so because the MUSB core
device still gets initialized as fs_initcall() -- which is late enough for the
I2C GPIO expander (which controls VBUS) to be initialized.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This patch adds definitions for spi devices on the tnetv107x evm platform.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This patch adds SSP configuration and pin muxing info for tnetv107x
evm boards.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This patch adds an SSP platform device definition for the tnetv107x soc family.
The clock lookup entry has also been updated to match.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This patch includes the implementation of the clock gating
for System MMU. Initially, all System MMUs are not asserted
the system clock. Asserting the system clock to a System MMU
is enabled only when s5p_sysmmu_enable() is called. Likewise,
it is disabled only when s5p_sysmmu_disable() is called.
Therefore, clock gating on System MMUs are still invisible to
the outside of the System MMU driver.
Signed-off-by: NKyongHo Cho <pullip.cho@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch includes the following enhancements for System MMU:
- Enhanced readability
- Removal of unused data structures or their members
- Simplified function definitions
- Corrections of some logical errors
- Full compliance with Linux coding style
- Simpler way of registering callback functions of System MMU faults
Signed-off-by: NKyongHo Cho <pullip.cho@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds support for gpio interrupts on Samsung EXYNOS4 platform.
Common s5p-gpioint.c code is used for handling gpio interrupts. Each gpio
line that needs gpio interrupt support must be later registered with
s5p_register_gpio_interrupt() function.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch removes all global data from common s5p gpio interrupt
handler code. This enables to reuse this code on EXYNOS4 platform.
Instead of global data (IRQ_GPIOINT interrupt number,
S5P_GPIOINT_GROUP_MAXNR groups count), a s5p_register_gpioint_bank()
function is introduced. It is aimed to be called from gpiolib init.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch performs a global cleanup in s5p gpio interrupt support code.
The code is prepared for upcoming support for gpio interrupts on EXYNOS4
platform, which has 2 gpio banks (regions) instead of one (like on
S5PC110 and S5PC100).
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>