If socket is create by PF_INET type, it can not used IPv6 address to
send/recv DATA, So we can not used IPv6 address even if peer tell us it
support IPv6 address.
This patch fix to only enabled peer IPv6 address support on PF_INET6 socket.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Determine the number of physical ports from the card's VPD data.
Previous fix failed on Maramba platform which doesn't have the
"board-model" property. This fix uses the "model" property which
exists on all cards and Neptune based motherboards.

cstyle cleanup included.
Signed-off-by: NMatheos Worku <matheos.worku@sun.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Noticed by Paul Marks <paul@pmarks.net>.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch increases the headroom TIPC reserves in each sk_buff
to accommodate the largest possible link level device header.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_open() and dev_close() must be called holding the RTNL, since they
call device functions and netdevice notifiers that are promised the RTNL.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tx packet counting and the local loopback of CAN frames should
only happen in the case that the CAN frame has been enqueued to the
netdevice tx queue successfully.

Thanks to Andre Naujoks <nautsch@gmail.com> for reporting this issue.
Signed-off-by: NOliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: NUrs Thuermann <urs@isnogud.escape.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a net namespace is destroyed, some devices (those, not killed
on ns stop explicitly) are moved back to init_net.

The problem, is that this net_ns change has one point of failure -
the __dev_alloc_name() may be called if a name collision occurs (and
this is easy to trigger). This allocator performs a likely-to-fail
GFP_ATOMIC allocation to find a suitable number. Other possible 
conditions that may cause error (for device being ns local or not
registered) are always false in this case.

So, when this call fails, the device is unregistered. But this is
*not* the right thing to do, since after this the device may be
released (and kfree-ed) improperly. E. g. bridges require more
actions (sysfs update, timer disarming, etc.), some other devices 
want to remove their private areas from lists, etc.

I. e. arbitrary use-after-free cases may occur.

The proposed fix is the following: since the only reason for the
dev_change_net_namespace to fail is the name generation, we may
give it a unique fall-back name w/o %d-s in it - the dev<ifindex>
one, since ifindexes are still unique.

So make this change, raise the failure-case printk loglevel to 
EMERG and replace the unregister_netdevice call with BUG().

[ Use snprintf() -DaveM ]
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When conntrack and DCCP/SCTP protocols are enabled, chances are good
that people also want DCCP/SCTP conntrack and NAT support.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some Inovaphone PBXs exhibit very stange behaviour: when dialing for
example "123", the device sends INVITE requests for "1", "12" and
"123" back to back.  The first requests will elicit error responses
from the receiver, causing the SIP helper to flush the RTP
expectations even though we might still see a positive response.

Note the sequence number of the last INVITE request that contained a
media description and only flush the expectations when receiving a
negative response for that sequence number.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noticed by Ben Greear, macvlan crashes the kernel when unloading the
module. The reason is that it tries to clean up the macvlan_port pointer
on the macvlan device itself instead of the underlying device. A non-NULL
pointer is taken as indication that the macvlan_handle_frame_hook is
valid, when receiving the next packet on the underlying device it tries
to call the NULL hook and crashes.

Clean up the macvlan_port on the correct device to fix this.

Signed-off-by; Patrick McHardy <kaber@trash.net>
Tested-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 1122 does not have a section 3.1.2.2. The requirement to silently
discard datagrams with a bad checksum is in section 3.2.1.2 instead.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=10611Signed-off-by: NJ.H.M. Dassen (Ray) <jdassen@debian.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Note: there's actually another bug in FRTO's SACK variant, which
is the causing failure in NewReno case because of the error
that's fixed here. I'll fix the SACK case separately (it's
a separate bug really, though related, but in order to fix that
I need to audit tp->snd_nxt usage a bit).

There were two places where SACK variant of FRTO is getting
incorrectly used even if SACK wasn't negotiated by the TCP flow.
This leads to incorrect setting of frto_highmark with NewReno
if a previous recovery was interrupted by another RTO.

An eventual fallback to conventional recovery then incorrectly
considers one or couple of segments as forward transmissions
though they weren't, which then are not LOST marked during
fallback making them "non-retransmittable" until the next RTO.
In a bad case, those segments are really lost and are the only
one left in the window. Thus TCP needs another RTO to continue.
The next FRTO, however, could again repeat the same events
making the progress of the TCP flow extremely slow.

In order for these events to occur at all, FRTO must occur
again in FRTOs step 3 while the key segments must be lost as
well, which is not too likely in practice. It seems to most
frequently with some small devices such as network printers
that *seem* to accept TCP segments only in-order. In cases
were key segments weren't lost, things get automatically
resolved because those wrongly marked segments don't need to be
retransmitted in order to continue.

I found a reproducer after digging up relevant reports (few
reports in total, none at netdev or lkml I know of), some
cases seemed to indicate middlebox issues which seems now
to be a false assumption some people had made. Bugzilla
#10063 _might_ be related. Damon L. Chesser <damon@damtek.com>
had a reproducable case and was kind enough to tcpdump it
for me. With the tcpdump log it was quite trivial to figure
out.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On a read error, e1000e might have returned uninitialized block of
eeprom data back to userspace. The convention is that 0xff is "empty",
so mark the entire eeprom as empty in case of an error.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 9fb1e350,
ucc_geth: use rx-clock-name and tx-clock-name device tree properties
Introduced a typo that made the driver use the RX clock
as TX clock, causing massive TX errors.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Otherwise theoretically at least

	CAP_NET_ADMIN
	Reload new firmware
	Wait..
	Firmware patches kernel

So it should be CAY_SYS_RAWIO - not that I suspect this is in fact a
credible attack vector!
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Delete the non-napi code from the driver and Kconfig.
Tested x86_64.  Apply at next open opportunity.
Signed-off-by: NDon Fry <pcnet32@verizon.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

There are more memory leaks in the !PPC_CPM_NEW_BINDING case, but that code
will disappear soon along with arch/ppc.

Reported by Daniel Marjamki <danielm77@spray.se> at
http://bugzilla.kernel.org/show_bug.cgi?id=10591Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Taken from http://bugzilla.kernel.org/show_bug.cgi?id=10577

I was unable to access a computer containing an Intel EtherExpress 16 network
card using IPv6.

I traced this to failure of neighbour discovery.  When I used an "ip -6 neigh
add" command, on the computer attempting access, to insert a binding between
the IPv6 address of the computer with the Intel EtherExpress 16 network card
and the card's ethernet address, I was able to access that computer using
IPv6.

Neighbour discovery requires working multicast.  The driver sources file
eexpress.c contains an approximately 30 line function eexp_setup_filter used
when loading multicast addresses.

I found 3 problems in this function

1) It wrote the number of multicast addresses to the card instead of the
    number of bytes in the multicast addresses.

2) When loading multiple multicast addresses it loaded the first one
    provided multiple times instead of loading each one once.

3) The setting of pointer 'data' from 'dmi->dmi_addr' occured before the
    test for the error situation of 'dmi' being NULL.

Correcting these problems allows the computer with the Intel EtherExpress 16
network card to found by IPv6 neighbour discovery.

p.s. There is some information on the Intel EtherExpress 16 at
http://www.intel.com/support/etherexpress/vintage/sb/cs-013500.htm
Datasheet for the Intel 82586 ethernet controller used by the card
http://www.datasheetcatalog.com/datasheets_pdf/8/2/5/8/82586.shtmlSigned-off-by: NBruce Robson <bns_robson@hotmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use net_device_stats from net_device structure instead of local.
Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: NSteffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The ethernet card 3c980-TX needs a mdio_sync() to initialize the ethernet
properly. This is forced by adding an EXTRA_PREAMBLE to its drv_flags.

Without this, the driver did not reconnect after a link loss.
Signed-off-by: NGunnar Larisch <Gunnar.Larisch@gmx.de>
Acked-by: NSteffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

drivers/net/appletalk/cops.c: In function ‘cops_reset’:
drivers/net/appletalk/cops.c:507: warning: comparison of distinct pointer
types lacks a cast

by replacing hand-woven msleep() with call to msleep()
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds support for the BM PHY, a new PHY model being used
on ICH9-based implementations.

This new PHY exposes issues in the ICH9 silicon when receiving
jumbo frames large enough to use more than a certain part of the
Rx FIFO, and this unfortunately breaks packet split jumbo receives.
For this reason we re-introduce (for affected adapters only) the
jumbo single-skb receive routine back so that people who do
wish to use jumbo frames on these ich9 platforms can do so.
Part of this problem has to do with CPU sleep states and to make
sure that all the wake up timings are correctly we force them
with the recently merged pm_qos infrastructure written by Mark
Gross. (See http://lkml.org/lkml/2007/10/4/400).

To make code read a bit easier we introduce a _IS_ICH flag so
that we don't need to do mac type checks over the code.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch fixes uli526x driver's issues on a PowerPC boards: uli chip
is unable to receive the packets.

It appears that send_frame_filter prepares the setup frame in the
endianness unsafe manner. On a big endian machines we should shift
the address nibble by two bytes.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The firmware on MPC8610HPCD boards enables ULI ethernet and leaves it
in some funky state before booting Linux. For drivers, it's always good
idea to (re)initialize the hardware prior to requesting interrupts.

This patch fixes the following oops:

Oops: Kernel access of bad area, sig: 11 [#1]
MPC86xx HPCD
NIP: c0172820 LR: c017287c CTR: 00000000
[...]
NIP [c0172820] allocate_rx_buffer+0x2c/0xb0
LR [c017287c] allocate_rx_buffer+0x88/0xb0
Call Trace:
[df82bdc0] [c017287c] allocate_rx_buffer+0x88/0xb0 (unreliable)
[df82bde0] [c0173000] uli526x_interrupt+0xe4/0x49c
[df82be20] [c0045418] request_irq+0xf0/0x114
[df82be50] [c01737b0] uli526x_open+0x48/0x160
[df82be70] [c0201184] dev_open+0xb0/0xe8
[df82be80] [c0200104] dev_change_flags+0x90/0x1bc
[df82bea0] [c035fab0] ip_auto_config+0x214/0xef4
[df82bf60] [c03421c8] kernel_init+0xc4/0x2ac
[df82bff0] [c0010834] kernel_thread+0x44/0x60
Instruction dump:
4e800020 9421ffe0 7c0802a6 bfa10014 7c7e1b78 90010024 80030060 83e30054
2b80002f 419d0078 3fa0c039 48000058 <907f0010> 80630088 2f830000 419e0014
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ucc_geth didn't have anything marked as __iomem.  It was also inconsistent
with its use of in/out accessors (using them sometimes, not using them other
times).  Cleaning this up cuts the warnings down from hundreds to just over a
dozen.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Declared some things static, declared some things in the header.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

During sparse cleanup, found a locking bug.  Some of the sysfs functions were
acquiring a lock, and then returning in the event of an error.  We rearrange
the code so that the lock is released in error conditions, too.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

	As part of:

commit c2edacf8
Author: Jay Vosburgh <fubar@us.ibm.com>
Date:   Mon Jul 9 10:42:47 2007 -0700

    bonding / ipv6: no addrconf for slaves separately from master

two steps were rearranged in the enslavement process: netdev_set_master
is now before the call to dev_open to open the slave.

	This patch updates the error cases and unwind process at the
end of bond_enslave to match the new order.  Without this patch, it is
possible for the enslavement to fail, but leave the slave with IFF_SLAVE
set in its flags.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The sysfs layer has an internal protection, that ensures, that
all the process sitting inside ->sore/->show callback exits
before the appropriate entry is unregistered (the calltraces
are rather big, but I can provide them if required).

On the other hand, bonding takes rtnl_lock in
a) the bonding_store_bonds, i.e. in ->store callback,
b) module exit before calling the sysfs unregister routines.

Thus, the classical AB-BA deadlock may occur. To reproduce run
# while :; do modprobe bonding; rmmod bonding; done
and
# while :; do echo '+bond%d' > /sys/class/net/bonding_masters ; done
in parallel.

The fix is to move the bond_destroy_sysfs out of the rtnl_lock,
but _before_ bond_free_all to make sure no bonding devices exist
after module unload.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

	Fixed an error unwind in bonding_store_bonds that didn't release
the locks it held, and consolidated unwinds into a common block at the
end of the function.  Bug reported by Pavel Emelyanov <xemul@openvz.org>,
who provided a different fix.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

If the call to bond_create_sysfs_entry in bond_create fails, the
proper rollback is to call unregister_netdevice, not free_netdev.
Otherwise - kernel BUG at net/core/dev.c:4057!

Checked with artificial failures injected into bond_create_sysfs_entry.

Pavel's original patch modified by Jay Vosburgh to move code around
for clarity (remove goto-hopping within the unwind block).
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

reallocation of the policy data was being ignored. It could fail.
Simplify so that there is no need for reallocating.
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IWLWIFI should be a tristate so that if IWLCORE and/or IWL3945 are m
and none of them is y kbuild doesn't create an empty 
drivers/net/wireless/built-in.o

This patch also removes the pointless "default n".
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 65e41136.

Unlike the other cases Pavel fixed, this case did not
setup a netdev->destructor of free_netdev, therefore this
change was not correct.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dccp_feat_change() validates length and on error is returning 1.
This happens to work since call chain is checking for 0 == success,
but this is returned to userspace, so make it a real error value.
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Acked-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

x86.git testing found this build bug on v2.6.26-rc1:

  ERROR: "pnp_get_resource" [drivers/net/irda/smsc-ircc2.ko] undefined!
  make[1]: *** [__modpost] Error 1
  make: *** [modules] Error 2

the driver did not anticipate the case of !CONFIG_PNP which is rare but 
still possible. Instead of restricting the driver to PNP-only in the 
Kconfig space, add the (trivial) dummy struct pnp_driver - this is that 
other drivers use in the !PNP case too.

The driver itself can in theory be initialized on !PNP too in certain 
cases, via smsc_ircc_legacy_probe().

Patch only minimally build tested, i dont have this hardware.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

x86.git testing found the following build failure in latest -git:

 drivers/built-in.o: In function `nsc_ircc_pnp_probe':
 nsc-ircc.c:(.text+0xdf1b6): undefined reference to `pnp_get_resource'
 nsc-ircc.c:(.text+0xdf1d4): undefined reference to `pnp_get_resource'
 nsc-ircc.c:(.text+0xdf1ee): undefined reference to `pnp_get_resource'
 nsc-ircc.c:(.text+0xdf237): undefined reference to `pnp_get_resource'
 nsc-ircc.c:(.text+0xdf24c): undefined reference to `pnp_get_resource'
 drivers/built-in.o:nsc-ircc.c:(.text+0xdf266): more undefined references to `pnp_get_resource' follow
 make: *** [.tmp_vmlinux1] Error 1

triggered via this config:

  http://redhat.com/~mingo/misc/config-Sat_May__3_20_53_13_CEST_2008.bad

while generally most users will have PNP enabled, drivers can support
non-PNP build mode too - and most drivers implement it. That is typically
done by providing a dummy pnp_driver structure that will not probe anything.

The fallback routines in the driver will handle this dumber mode of
operation too.

This patch implements that. I have not tested whether this actually
works on real hardware so take care. It does resolve the build bug.

[ Another solution that is used by a few drivers is to exclude the driver
  in the Kconfig if PNP is disabled, via "depends on PNP", but this would
  limit the availability of the driver needlessly. ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert to netlink helpers by using netlink policy validation.
As a side effect fixes a leak.
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>