The ACCES 104-IDI-48 family of PC/104 utility boards feature 48
individually optically isolated digital inputs. Enabled inputs feature
change-of-state detection capability; if change-of-state detection is
enabled, an interrupt is fired off if a change of input level
(low-to-high or high-to-low) is detected. Change-of-state IRQs are
enabled/disabled on 8-bit boundaries, for a total of six boundaries.

This driver provides GPIO and IRQ support for these 48 channels of
digital input. The base port address for the device may be configured
via the idi_48_base module parameter. The interrupt line number for the
device may be configured via the idi_48_irq module parameter.
Signed-off-by: NWilliam Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NNizam Haider <nijamh@cdac.in>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

IRQ should be disabled on device probe so that the device IRQ is in a
known starting state. If IRQ is not disabled, interrupts may be reported
as handled by the IRQ handler, despite no irq_unmask calls made by the
user.
Signed-off-by: NWilliam Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Commit f4d566a8a0e6 ("gpio: change member .dev to .parent") changes
member of gpiochip from .dev to .parent. Update the corresponding
comment.
Signed-off-by: NBamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

To prevent confusion, and to match the existing coding style used in
other GPIO drivers, symbol names within the 104-idio-16 GPIO driver
should be lowercase.
Signed-off-by: NWilliam Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

We need to check if number of gpio is positive if there is no
such check in devicetree or acpi or whatever called before
gpiochip_add.

I suppose that devicetree and acpi do not allow insert gpiochip
with zero number but I do not know if it is enough to ignore
this check in gpiochip_add.
Signed-off-by: NBamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

There are limitations for the current checker:
1.  Could not check the overlap if the new gpiochip is the secondly
    gpiochip.
2.  Could not check the overlap if the new gpiochip is overlap
    with the left of gpiochip. E.g. if we insert [c, d] between
    [a,b] and [e, f], and e >= c + d, it will successful even if
    c < a + b.
3.  Allow overlap of base of different gpiochip.

This patch fix these issues by checking the overlap of both right and
left gpiochip in the same loop statement.
Signed-off-by: NBamvor Jian Zhang <bamvor.zhangjian@linaro.org>
[Tweaked to remove unnecessary ret variable]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The commit f881bab0 ("gpio: keep the GPIO line names internal")
change the error to warning in gpiochip_set_desc_names. Update the
comment accordingly.
Signed-off-by: NBamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch is a second attempt at what was previously in commit
6c7e660a ("gpio: pxa: set initcall level to module init").

The goal is the same : enable gpio & pinctrl driver to work
together. As pinctrl driver will be initialized at device level, the
gpio should be as well, so that the deferring mechanism is honored.

Yet this patch should also respect the legacy platforms, so the set of
constraints is :
 - in legacy platforms (ie. non dt), gpio_[gs]et_*() should be available
   for machine code => core initcall
 - in new platforms (ie. dt based), pinctrl will be available and no
   machine code => device initcall

In order to fullfill all these constraints, the initcall level is either
postcore for non devicetree platforms, and device for devicetree platforms.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

We should not fall back to the legacy unnamed gpio lookup style if the
driver requests gpios with different names, because we'll give out the same
gpio twice. Let's keep track of the names that were used for the device and
only do the fallback for the first name used.
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The ACCES 104-IDIO-16 series offers Change-of-State detection interrupt
functionality; if Change-of-State detection is enabled, an interrupt is
fired off if any input line changes state (i.e. goes from low to high,
or from high to low). This patch adds support to handle these interrupts
and allows the user to mask which GPIO lines are affected. The interrupt
line number for the device may be set via the idio_16_irq module
parameter.
Signed-off-by: NWilliam Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.

This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:

@@
struct gpio_chip *var;
@@
-var->dev
+var->parent

and:

@@
struct gpio_chip var;
@@
-var.dev
+var.parent

and:

@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent

Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.

This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.

Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Acked-by: NHans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

After merging the scsi tree, today's linux-next build (powerpc
allyesconfig) failed like this:

In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:59:0:
drivers/scsi/mpt3sas/mpt3sas_scsih.c: In function '_scsih_io_done':
drivers/scsi/mpt3sas/mpt3sas_base.h:1414:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_get': function body not available
 mpt3sas_scsi_direct_io_get(struct MPT3SAS_ADAPTER *ioc, u16 smid);
 ^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4448:6: error: called from here
  if (mpt3sas_scsi_direct_io_get(ioc, smid) &&
      ^
In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:59:0:
drivers/scsi/mpt3sas/mpt3sas_base.h:1416:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_set': function body not available
 mpt3sas_scsi_direct_io_set(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 direct_io);
 ^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4454:3: error: called from here
   mpt3sas_scsi_direct_io_set(ioc, smid, 0);
   ^
In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:5
9:0:
drivers/scsi/mpt3sas/mpt3sas_base.h:1416:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_set': function body not available
 mpt3sas_scsi_direct_io_set(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 direct_io);
 ^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4454:3: error: called from here
   mpt3sas_scsi_direct_io_set(ioc, smid, 0);
   ^

Presumably caused by commit

  c84b06a4 ("mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs")
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

This reverts commit 52f5eb60.

Rockchip drm can't work with generic drm_of_component_probe now
Signed-off-by: NMark Yao <mark.yao@rock-chips.com>
Acked-by: NLiviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Seems the crtc helpers call drm_calc_timestamping_constants()
unconditionally even if the driver didn't initialize vblank support by
calling drm_vblank_init(). That used to be OK since the constants were
stored under drm_crtc.

However I broke this with
commit eba1f35d ("drm: Move timestamping constants into drm_vblank_crtc")
when I moved the constants to live inside the drm_vblank_crtc struct
instead. If drm_vblank_init() isn't called, we don't allocate these
structures, and so drm_calc_timestamping_constants() will oops.

Fix it by adding a check into drm_calc_timestamping_constants() to see
if vblank support was initialized at all. And to keep in line with other
such checks, also toss in a check and warn for the case where vblank
support was initialized, but the wrong number of crtcs was specified.

Fixes the following sort of oops:
 BUG: unable to handle kernel NULL pointer dereference at 00000000000000b0
 IP: [<ffffffffa014b266>] drm_calc_timestamping_constants+0x86/0x130 [drm]
 PGD 0
 Oops: 0002 [#1] SMP
 Modules linked in: sr_mod cdrom mgag200(+) i2c_algo_bit drm_kms_helper ahci syscopyarea sysfillrect sysimgblt libahci fb_sys_fops bnx2x ttm tg3(+) mdio drm ptp sd_mod libata i2c_core pps_core libcrc32c hpsa dm_mirror dm_region_hash dm_log dm_mod
 CPU: 0 PID: 418 Comm: kworker/0:2 Not tainted 4.3.0+ #1
 Hardware name: HP ProLiant DL380 Gen9, BIOS P89 06/09/2015
 Workqueue: events work_for_cpu_fn
 task: ffff88046ca95500 ti: ffff88007830c000 task.ti: ffff88007830c000
 RIP: 0010:[<ffffffffa014b266>]  [<ffffffffa014b266>] drm_calc_timestamping_constants+0x86/0x130 [drm]
 RSP: 0018:ffff88007830f4e8  EFLAGS: 00010246
 RAX: 0000000000fe4c00 RBX: ffff88006a849160 RCX: 0000000000000540
 RDX: 0000000000000000 RSI: 000000000000fde8 RDI: ffff88006a849000
 RBP: ffff88007830f518 R08: ffff88007830c000 R09: 00000001b87e3712
 R10: 00000000000050c4 R11: 0000000000000000 R12: 0000000000fe4c00
 R13: ffff88006a849000 R14: 0000000000000000 R15: 000000000000fde8
 FS:  0000000000000000(0000) GS:ffff88046f800000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 00000000000000b0 CR3: 00000000019d6000 CR4: 00000000001406f0
 Stack:
  ffff88007830f518 ffff88006a849000 ffff880c69b90340 ffff880c69b90000
  ffff880c69b90348 ffff880c69b90340 ffff88007830f748 ffffffffa042f7e7
  ffff88006a849090 0000000000000000 ffff88006a849160 0000000000000000
 Call Trace:
  [<ffffffffa042f7e7>] drm_crtc_helper_set_mode+0x3d7/0x4b0 [drm_kms_helper]
  [<ffffffffa04307d4>] drm_crtc_helper_set_config+0x8d4/0xb10 [drm_kms_helper]
  [<ffffffffa01548d4>] drm_mode_set_config_internal+0x64/0x100 [drm]
  [<ffffffffa043c342>] drm_fb_helper_pan_display+0xa2/0x280 [drm_kms_helper]
  [<ffffffff81392c7b>] fb_pan_display+0xbb/0x170
  [<ffffffff8138cf70>] bit_update_start+0x20/0x50
  [<ffffffff8138b81b>] fbcon_switch+0x39b/0x590
  [<ffffffff8140a3d0>] redraw_screen+0x1a0/0x240
  [<ffffffff8140b30e>] do_bind_con_driver+0x2ee/0x310
  [<ffffffff8140b651>] do_take_over_console+0x141/0x1b0
  [<ffffffff81387377>] do_fbcon_takeover+0x57/0xb0
  [<ffffffff8138c98b>] fbcon_event_notify+0x60b/0x750
  [<ffffffff810a5599>] notifier_call_chain+0x49/0x70
  [<ffffffff810a58dd>] __blocking_notifier_call_chain+0x4d/0x70
  [<ffffffff810a5916>] blocking_notifier_call_chain+0x16/0x20
  [<ffffffff8139282b>] fb_notifier_call_chain+0x1b/0x20
  [<ffffffff81394881>] register_framebuffer+0x1f1/0x330
  [<ffffffffa043d9aa>] drm_fb_helper_initial_config+0x27a/0x3d0 [drm_kms_helper]
  [<ffffffffa0469b4d>] mgag200_fbdev_init+0xdd/0xf0 [mgag200]
  [<ffffffffa0468586>] mgag200_modeset_init+0x176/0x1e0 [mgag200]
  [<ffffffffa0464659>] mgag200_driver_load+0x3f9/0x580 [mgag200]
  [<ffffffffa014e067>] drm_dev_register+0xa7/0xb0 [drm]
  [<ffffffffa015054f>] drm_get_pci_dev+0x8f/0x1e0 [drm]
  [<ffffffffa046937b>] mga_pci_probe+0x9b/0xc0 [mgag200]
  [<ffffffff813662d5>] local_pci_probe+0x45/0xa0
  [<ffffffff8109afe4>] work_for_cpu_fn+0x14/0x20
  [<ffffffff8109e13c>] process_one_work+0x14c/0x3c0
  [<ffffffff8109eaa4>] worker_thread+0x244/0x470
  [<ffffffff8168bfba>] ? __schedule+0x2aa/0x760
  [<ffffffff8109e860>] ? rescuer_thread+0x310/0x310
  [<ffffffff810a4438>] kthread+0xd8/0xf0
  [<ffffffff810a4360>] ? kthread_park+0x60/0x60
  [<ffffffff8169030f>] ret_from_fork+0x3f/0x70
  [<ffffffff810a4360>] ? kthread_park+0x60/0x60
 Code: f6 31 d2 41 89 c2 8b 83 b4 00 00 00 0f af c1 48 98 48 69 c0 40 42 0f 00 48 f7 f6 f6 43 74 10 41 89 c4 75 26 f6 05 9a 6f 03 00 01 <45> 89 96 b0 00 00 00 45 89 a6 ac 00 00 00 75 35 48 83 c4 08 5b
 RIP  [<ffffffffa014b266>] drm_calc_timestamping_constants+0x86/0x130 [drm]
  RSP <ffff88007830f4e8>
 CR2: 00000000000000b0

Cc: Jeff Moyer <jmoyer@redhat.com>
Reported-by: NJeff Moyer <jmoyer@redhat.com>
References: http://lists.freedesktop.org/archives/dri-devel/2015-November/094217.html
Fixes: eba1f35d ("drm: Move timestamping constants into drm_vblank_crtc")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This masking prevents access to the end of the device via dax_do_io(),
and is unnecessary as arch_add_memory() would have rejected an unaligned
allocation.

Cc: <stable@vger.kernel.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Rather than punt on the numa node for these e820 ranges try to find a
better answer with memory_add_physaddr_to_nid() when it is available.

Cc: <stable@vger.kernel.org>
Reported-by: NBoaz Harrosh <boaz@plexistor.com>
Tested-by: NBoaz Harrosh <boaz@plexistor.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Missing a include file caused compile error.

  drivers/thermal/rockchip_thermal.c: In function 'rockchip_thermal_suspend':
  drivers/thermal/rockchip_thermal.c:720:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]
  ...

Fixes: 7e38a5b1 ("thermal: rockchip: support the sleep pinctrl state
to avoid glitches")
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Nkbuild test robot <lkp@intel.com>
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Signed-off-by: NEduardo Valentin <edubezval@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

According to SPC-4, in a Mode Select, the PS bit in Mode Pages is
reserved and must be set to 0 by the driver.  In the sd implementation,
function cache_type_store does a Mode Sense, which might set the PS bit
on the read buffer, followed by a Mode Select, which receives the same
buffer, without explicitly clearing the PS bit.  So, in cases where
target supports saving the Mode Page to a non-volatile location, we end
up doing a Mode Select with the PS bit set, which could cause an illegal
request error if the target is checking this.

This was observed on a new firmware change, which was subsequently
reverted, but this changes sd.c to be more compliant with SPC-4.

This patch clears the PS bit in the buffer returned by Mode Select,
right before it is used in the Mode Select command.
Signed-off-by: NGabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

As defined in 4.6.9 of SAM-4, the encoding of LUN is
on 5 bits (max_lun=32) and the current value is only 8.
Set max_lun to IBMVSCSI_MAX_LUN (32).
Signed-off-by: NLaurent Vivier <lvivier@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

As devices with values greater than that are silently ignored,
this gives some hints to the sys admin to know why he doesn't see
his devices...
Signed-off-by: NLaurent Vivier <lvivier@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There is a static checker warning here because "bytes" is controlled by
the user and we cap the upper bound with min() but allow negatives.
Negative bytes will result in some nasty warning messages but are not
super harmful.  Anyway, no one needs negative bytes so let's just check
for it and return NULL.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Replace the use of struct timeval and do_gettimeofday() with
64 bit ktime_get_real_seconds. Prevents 32-bit type overflow
in year 2038 on 32-bit systems.

Driver was using the seconds portion of struct timeval (.tv_secs)
to pass a millseconds timestamp to the firmware. This change maintains
that same behavior using ktime_get_real_seconds.

The structure used to pass the timestamp to firmware is 48 bits and
works fine as long as the top 16 bits are zero and they will be zero
for a long time..ie. thousands of years.

Alternative Change:  Add sub second granularity to timestamp

As noted above, the driver only used the seconds portion of timeval,
ignores the microseconds portion, and by multiplying by 1000 effectively
does a <<10 and always writes zero into timestamp[0].

The alternative change would pass all the bits to the firmware:

        struct timespec64 ts;

        ktime_get_real_ts64(&ts);
        timestamp = ts.tv_sec * MSEC_PER_SEC + ts.tv_nsec / NSEC_PER_MSEC;
Signed-off-by: NAlison Schofield <amsfield22@gmail.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

struct mvumi_hs_page2 stores a "seconds_since1970" field which is of
type u64. It is however, written to, using 'struct timeval' which has
a 32-bit seconds field and whose value will overflow in year 2038.
This patch uses ktime_get_real_seconds() instead since it provides a
64-bit seconds value, which is 2038 safe.
Signed-off-by: NTina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

drivers/scsi/be2iscsi/be_main.c: In function 'be_sgl_create_contiguous':
drivers/scsi/be2iscsi/be_main.c:3187:18: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
  WARN_ON(!length > 0);

gcc version 5.2.1
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Cc: Jayamohan Kallickal <jayamohan.kallickal@avagotech.com>
Cc: Minh Tran <minh.tran@avagotech.com>
Cc: John Soni Jose <sony.john-n@avagotech.com>
Cc: "James E.J. Bottomley" <JBottomley@odin.com>
Reported-by: NJoel Stanley <joel@jms.id.au>
Reviewed-by: NManoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The only user of scsi_prep_async_scan() is scsi_scan_host() and it
handles the situation correctly. Move 'called twice' reporting to debug
level as well.

The issue is observed on Hyper-V: on any device add/remove event storvsc
driver calls scsi_scan_host() and in case previous scan is still running
we get the message and stack dump on console.
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Tested-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Bump mpt3sas driver version to 09.102.00.00
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Modified the mpt3sas driver to have a single driver module which
supports both SAS 2.0 & SAS 3.0 HBA devices.

* Added SAS 2.0 HBA device IDs to the mpt3sas_pci_table pci table.

* Created two separate SCSI host templates for SAS2 and SAS3 HBAs so
  that, during the driver load time driver can use corresponding host
  template(based the pci device ID) while registering a scsi host
  adapter instance for that pci device.

* Registered two IOCTL devices, mpt2ctl is for SAS2 HBAs & mpt3ctl for
  SAS3 HBAs. Also updated the code to make sure that mpt2ctl device
  processes only those ioctl cmds issued for the SAS2 HBAs and mpt3ctl
  device processes only those ioctl cmds issued for the SAS3 HBAs.

* Added separate indexing for SAS2 and SAS3 HBAs.

* Replaced compile time check 'MPT2SAS_SCSI' to run time check
  'hba_mpi_version_belonged' whereever needed.

* Aliased this merged driver to mpt2sas using MODULE_ALIAS.

* Moved global varaible 'driver_name' to per adapter instance variable.

* Created two raid function template and used corresponding raid
  function templates based on the run time check
  'hba_mpi_version_belonged'.

* Moved mpt2sas_warpdrive.c file from mpt2sas to mpt3sas folder and
  renamed it as mpt3sas_warpdrive.c.

* Also renamed the functions in mpt3sas_warpdrive.c file to follow
  current driver function name convention.

* Updated the Makefile to build mpt3sas_warpdrive.o file for these
  WarpDrive-specific functions.

* Also in function mpt3sas_setup_direct_io(), used sector_div() API
  instead of division operator (which gives compilation errors on 32 bit
  machines).

* Removed mpt2sas files, mpt2sas directory & mpt3sas_module.c file.

* Added module parameter 'hbas_to_enumerate' which permits using this
  merged driver as a legacy mpt2sas driver or as a legacy mpt3sas
  driver.

  Here are the available options for this module parameter:

   0 - Merged driver which enumerates both SAS 2.0 & SAS 3.0 HBAs
   1 - Acts as legacy mpt2sas driver, which enumerates only SAS 2.0 HBAs
   2 - Acts as legacy mpt3sas driver, which enumerates only SAS 3.0 HBAs

* Removed mpt2sas entries from SCSI's Kconfig and Makefile files.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Bump the mpt2sas driver version to 20.102.00.00 and
Bump the mpt3sas driver version to 9.101.00.00.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

setpci reset on nytro warpdrive card along with sysfs access and cli
ioctl access resulted in kernel oops

1. pci_access_mutex lock added to provide synchronization between IOCTL,
   sysfs, PCI resource handling path

2. gioc_lock spinlock to protect list operations over multiple
   controllers

This patch is ported from commit 6229b414 ("mpt2sas: setpci reset
kernel oops fix").
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added OEM Gen2 PnP ID branding names from mpt2sas driver.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The fw_event_work struct is concurrently referenced at shutdown. Add a
refcount to protect it and refactor the code to use it.

Additionally, refactor _scsih_fw_event_cleanup_queue() such that it no
longer iterates over the list without holding the lock since
_firmware_event_work() concurrently deletes items from the list.

This patch is ported from commit 008549f6 ("mpt2sas: Refcount
fw_events and fix unsafe list usage"). These changes are also required
for mpt3sas.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

sas_device objects can be referenced concurrently throughout the driver.
We need a way to make sure threads can't delete them out from under each
other. This patch adds the refcount and refactors the code to use it.

Additionally, we cannot iterate over the sas_device_list without holding
the lock or we risk corrupting random memory if items are added or
deleted as we iterate. This patch refactors _scsih_probe_sas() to use
the sas_device_list in a safe way.

This patch is ported from the following mpt2sas driver commit
d224fe0d ("mpt2sas: Refcount sas_device objects and fix unsafe list
usage").
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

A new sysfs shost attribute called "BMR_status" is implemented to report
Backup Rail Monitor status.

This attribute is located in:

        /sys/class/scsi_host/host#/BMR_status

When reading this adapter attribute, the driver will output the state of
GPIO[24]. It returns "0" if BMR is healthy and "1" for failure.

If it returns an empty string then it means that there was an error
while obtaining the BMR status. Check dmesg for what error has occurred.

This sysfs shost attribute is mainly for WarpDrive controllers.

This commit is a port of 6c265660 ("mpt2sas: Provide sysfs attribute
to report Backup Rail Monitor Status").
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Ported the following list of WarpDrive-specific patches:

1. commit 0bdccdb0 ("mpt2sas: WarpDrive
   New product SSS6200 support added")

2. commit 82a45258 ("mpt2sas: WarpDrive
   Infinite command retries due to wrong scsi command entry in MPI
   message")

3. commit ba96bd0b ("mpt2sas: Support
   for greater than 2TB capacity WarpDrive")

4. commit 4da7af94 ("mpt2sas: Do not
   retry a timed out direct IO for Warpdrive")

5. commit daeaa9df ("mpt2sas: Avoid type
   casting for direct I/O commands").

Also set the mpt2_ioctl_iocinfo adapter_type to:

1. MPT3_IOCTL_INTERFACE_SAS3 for Gen3 HBAs

2. MPT2_IOCTL_INTERFACE_SAS2_SSS6200 for Warp Drive

3. MPT2_IOCTL_INTERFACE_SAS2  for other Gen2 HBAs
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch stops the driver to invoke kthread (which remove the dead
ioc) for some time while EEH recovery has started.

This patch is a port of commit b4730fb6 ("mpt2sas: fix for driver
fails EEH, recovery from injected pci bus error")'.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1. Do not enable MSI-X vectors for SAS2008 B0 controllers

2. Enable a single MSI-X vector for the following controller:

   a. SAS2004
   b. SAS2008
   c. SAS2008_1
   d. SAS2008_2
   e. SAS2008_3
   f. SAS2116_1
   g. SAS2116_2

3. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
   for Gen3 Invader/Fury C0 and above revision HBAs

4. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
   for all Intruder and Cutlass HBAs
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Avoid sending PHYDISK_HIDDEN RAID action requests to SAS2 controllers
since they don't support it.

Also enable fast_path only for SAS3 HBAs.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Gen2 HBAs use MPI scatter-gather lists whereas Gen3 HBAs use IEEE
scatter-gather lists. Modify the common code part in such a way that it
will build IEEE SGL tables for Gen3 HBAs and MPI SGL tables for Gen2
HBAs.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>