提交 · 6d78bd56be54286a72413db82d87fc371867629f · openeuler / raspberrypi-kernel

25 5月, 2011 28 次提交

[SCSI] qla4xxx: Complete the cmd if sense_len is zero · 6d78bd56

由 Prasanna Mumbai 提交于 5月 17, 2011

Complete the cmd if sense length is zero. For cases where sense
data spans across multiple iocb's by FW, we need to hold on to the
I/O (ha->status_srb != NULL) till we have processed them all and
copied the sense data from internal buffer to scsi_cmd sense buffer.
Signed-off-by: NPrasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

6d78bd56

[SCSI] qla4xxx: Dump HW/FW reg to figure out what caused FW to be hung for ISP82XX · 68d92ebf

由 Vikas Chaudhary 提交于 5月 17, 2011

Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

68d92ebf

[SCSI] qla4xxx: Updated the reset sequence for ISP82xx · cb74428e

由 Vikas Chaudhary 提交于 5月 17, 2011

Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

cb74428e

[SCSI] qla4xxx: update function qla4xxx_isr_decode_mailbox() · 185f107e

由 Prasanna Mumbai 提交于 5月 17, 2011

- Added MBOX_ASTS_DUPLICATE_IP AEN handling.
- Update MBOX_AEN_REG_COUNT to 8 so that driver will save status
  of all mbox registers in aen_q
Signed-off-by: NPrasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

185f107e

[SCSI] scsi_trace: Decode UNMAP bit in WRITE SAME(10) · c498bf1a

由 Martin K. Petersen 提交于 5月 18, 2011

As of SBC3r26 WRITE SAME(10) supports the UNMAP bit.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

c498bf1a

[SCSI] mpt2sas: Fix missing reference tag seed with Type 2 devices · 756aca7e

由 Martin K. Petersen 提交于 5月 18, 2011

Ensure that the initial reference tag is passed on to the HBA firmware
for DIF Type 2 devices.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Acked-by: NKashyap Desai <Kashyap.Desai@lsi.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

756aca7e

[SCSI] sd: Unmap discard alignment needs to be converted to bytes · 2a8cfad0

由 Martin K. Petersen 提交于 5月 18, 2011

The block layer discard alignment is reported in bytes, not in units of
the logical block size.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

2a8cfad0

[SCSI] bfa: kdump fix · 45d7f0cc

由 Jing Huang 提交于 4月 13, 2011

Root cause: When kernel crashes, bfa IOC state machine and FW doesn't get
a notification and hence are not cleanly shutdown. So registers holding
driver/IOC state information are not reset back to valid disabled/parking
values. This causes subsequent driver initialization to hang during kdump
kernel boot.

Fix description: during the initialization of first PCI function, reset
corresponding register when unclean shutown is detect by reading chip
registers. This will make sure that ioc/fw gets clean re-initialization.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

45d7f0cc

[SCSI] ipr: fix possible false positive detection of stuck interrupt · a5442ba4

由 Wayne Boyer 提交于 5月 17, 2011

If the driver is getting flooded with interrupts, there's a possibility
that the interrupt service routine could falsely detect a stuck interrupt
condition and reset the adapter.

This patch changes the logic such that the routine will loop back into
the command processing code one more time after detecting the stuck
interrupt signature. If there are no commands to process after that pass,
and the interrupt is still not cleared, then the driver will print the
"Error clearing HRRQ" message and reset the adapter.
Signed-off-by: NWayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

a5442ba4

[SCSI] libfcoe: Remove unnecessary module state checks · d85e607b

由 Robert Love 提交于 5月 16, 2011

libfcoe's interface consists of create, destroy, enable,
disable and create_vn2vn. These are currently module
paramaters added durring the module initialization. A
concern arose that the module parameters were being added
with write permissions before the module had completed
initialization. The following code was added to each
sysfs store file.

* Make sure the module has been initialized, and is not about to be
* removed.  Module parameter sysfs files are writable before the
* module_init function is called and after module_exit.
*/
if (THIS_MODULE->state != MODULE_STATE_LIVE)
    goto out_nodev;

This check was called out as unhelpful as the module can
go dead at any time and therefore its state isn't a reliable
thing to look at as a sign of stability and initialization
completion. Also, that functional interfaces like these
should be added after module initialization.

This patch removes the unnecessary checks and hopes to
disprove the concern about initialization ordering.

Recent fcoe transport rework changes now require fcoe
transports to register with libfcoe before any operation
can take place. libfcoe may access some static variables
but nothing that could cause a problem. Once a fcoe transport
is registered, libfcoe is usable and any interface calls will
be functional.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

d85e607b

[SCSI] libfc: do not immediately retry the cmd when seq_send fails in fc_fcp_send_data · 8467b96c

由 Yi Zou 提交于 5月 16, 2011

Currently, when seq_send() fails in fc_fcp_send_data(),
fc_fcp_retry_cmd() would complete this failed I/O directly and let
scsi-ml retry. However, target side is not notified which may hang the
target. Instead, we should just bail out from from fc_fcp_send_data
and let scsi-ml times it out and aborts this I/O instead.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

8467b96c

[SCSI] libfc: fix race in SRR response · 0a219edb

由 Vasu Dev 提交于 5月 16, 2011

In this case fsp was freed before error handler was invoked,
this is fixed by having SRR fsp reference freed by exch
destructor so that fsp will be always held until it exch
is freed.

Also don't reset fsp->recov_seq since this is needed by
SRR error handler to do exch done.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

0a219edb

[SCSI] libfc: don't call resp handler after FC_EX_TIMEOUT · 8d23f4ba

由 Vasu Dev 提交于 5月 16, 2011

In cases exch is already timed out then exch layer could
end up calling resp handler again for its response frame
received after timeout, though in this case fc_exch_timeout
handler would have already called resp with FC_EX_TIMEOUT.

This would cause REC response handler to release its
fsp pkt hold twice instead once and possibly similar issues
with other ELS exchanges in this race.

To avoid this race have resp updated under exch lock
in rx path, the resp would get set to NULL in case
of FC_EX_TIMEOUT under the same lock to prevent resp
callback after FC_EX_TIMEOUT.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

8d23f4ba

[SCSI] libfc: release DDP context if frame_send() fails · 6a716a85

由 Yi Zou 提交于 5月 16, 2011

In case frame_send() fails, make sure to let the underlying HW release the DDP
context that has already been set up before calling frame_send().
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

6a716a85

[SCSI] libfc: fix mm leak in handling incoming request for target discovery · 83383dd1

由 Hillf Danton 提交于 5月 16, 2011

When handling incoming request, if the operation code carried by the
received frame is not RSCN, the frame should be freed as in the RSCN
case, or there is memory leakage.
Signed-off-by: NHillf Danton <dhillf@gmail.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

83383dd1

[SCSI] fcoe: Prevent creation of an NPIV port with duplicate WWPN · bdf25218

由 Neerav Parikh 提交于 5月 16, 2011

This patch adds a validation step before allowing creation of a new NPIV port.
It checks whether the WWPN passed for the new NPIV port to be created is unique
for the given physical port.
Signed-off-by: NNeerav Parikh <Neerav.Parikh@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

bdf25218

[SCSI] libfcoe: Incorrect CVL handling for NPIV ports · c051ad2e

由 Bhanu Prakash Gollapudi 提交于 5月 16, 2011

Host doesnt handle CVL to NPIV instantiated ports correctly.
- As per FC-BB-5 Rev 2 CVLs with no VN_Port descriptors shall be treated as
  implicit logout of ALL vn_ports.
- CVL for NPIV ports should be handled before physical port even if descriptor
  for physical port appears before NPIV ports
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

c051ad2e

[SCSI] megaraid_sas: Version and Changelog update · 4f788dce