Some switch has dedicated SMI PHY Command and Data registers, used to
indirectly access the PHYs, instead of direct access.

Identify these switch models and make mv88e6xxx_phy_{read,write} generic
enough to support every models.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a MV88E6XXX_FLAG_PPU flag to describe switch models with a PHY
Polling Unit. This allows to merge PPU specific PHY access code in the
share code.

Make the mv88e6xxx_ppu_disable and mv88e6xxx_phy_{read,write}_ppu
functions use unlocked register accesses in order to call them in
mv88e6xxx_phy_{read,write} in a locked context.

Since the PPU code is shared, also remove NET_DSA_MV88E6XXX_NEED_PPU.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a flags bitmap to the info structure in order to identify features
supported or not by the different switch models.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dsa_switch structure ds is actually needed in very few places,
mostly during setup of the switch. The private structure ps is however
needed nearly everywhere. Pass ps, not ds internally.

[vd: rebased Andrew's patch.]
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ps->id is not needed anymore, so remove it as well as the related
defined values.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the number of databases to the info structure.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drop the ps->num_ports variable in favor of a new member of the info
structure. This removes the need to assign it at setup time.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add an mv88e6xxx_family enum to the info structure for better family
indentification.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new switch info structure which is meant to store switch models
static information, such as product number, name, number of ports,
number of databases, etc.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no point in having a special case for the revision when probing
a switch model. The code gets cluttered with unnecessary defines, and
leads to errors when code such as mv88e6131_setup compares
PORT_SWITCH_ID_6131_B2 to ps->id which masks the revision.

Drop every revision definition, and lookup only the product number.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the dsa_switch_driver.probe function to return a const char *.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These macros hide a ds variable and a return statement on error, which
can lead to locking issues. Kill them off.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than looking up the mii bus and address every time, do it once
at probe, and keep it in the private structure. Centralise this probe
code in mv88e6xxx.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now the switch devices have a dev pointer, make use of it for allocating
the drivers private data structures using a devm_kzalloc().
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The switchdev design implies that a software error should not happen in
the commit phase since it must have been previously reported in the
prepare phase. If an hardware error occurs during the commit phase,
there is nothing switchdev can do about it.

The DSA layer separates port_vlan_prepare and port_vlan_add for
simplicity and convenience. If an hardware error occurs during the
commit phase, there is no need to report it outside the driver itself.

Make the DSA port_vlan_add routine return void for explicitness.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The switchdev design implies that a software error should not happen in
the commit phase since it must have been previously reported in the
prepare phase. If an hardware error occurs during the commit phase,
there is nothing switchdev can do about it.

The DSA layer separates port_fdb_prepare and port_fdb_add for simplicity
and convenience. If an hardware error occurs during the commit phase,
there is no need to report it outside the DSA driver itself.

Make the DSA port_fdb_add routine return void for explicitness.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DSA layer doesn't care about the return code of the port_stp_update
routine, so make it void in the layer and the DSA drivers.

Replace the useless dsa_slave_stp_update function with a
dsa_slave_stp_state function used to reply to the switchdev
SWITCHDEV_ATTR_ID_PORT_STP_STATE attribute.

In the meantime, rename port_stp_update to port_stp_state_set to
explicit the state change.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the vendor-specific bootloaders set up this part
of the initialization for us, so this was never added.
However, since upstream bootloaders don't initialize the
chip specifically, they leave the fiber MII's PDOWN flag
set, which means that the CPU port doesn't connect.

This patch checks whether this flag has been clear prior
by something else, and if not make us clear it.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NPatrick Uiterwijk <patrick@puiterwijk.org>
Tested-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netdev_upper_dev_unlink() which notifies NETDEV_CHANGEUPPER, returns
void, as well as del_nbp(). So there's no advantage to catch an eventual
error from the port_bridge_leave routine at the DSA level.

Make this routine void for the DSA layer and its existing drivers.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All the drivers support multiple chips, but mv88e6123_61_65 is the
only one that reflects this in its naming. Change it to be consistent
with the other drivers.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Apply a few non-functional changes on the port state setter:

  * add a dynamic debug message with state names to track changes
  * explicit states checking instead of assuming their numeric values
  * lock mutex only once when changing several port states
  * use bitmap macros to declare and access port_state_update_mask
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement port_vlan_filtering in the driver to toggle the related port
802.1Q mode between DISABLED and SECURE, on user request.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restore per-port FDB. Assign them on setup, allow adding and deleting
addresses into them, and dump them.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a _mv88e6xxx_fid_new function which gives and flushes the lowest FID
available. Call it when preparing a new VTU entry.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the port_pvid_get and vlan_getnext functions in favor of a
simpler mv88e6xxx_port_vlan_dump function.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some DSA drivers may or may not support multiple software bridges on top
of an hardware switch.

It is more convenient for them to access the bridge's net_device for
finer configuration.

Removing the need to craft and access a bitmask also simplifies the
code.

This patch changes the signature of bridge related functions, update DSA
drivers, and removes dsa_slave_br_port_mask.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a per-port mv88e6xxx_priv_port structure to store per-port related
data, instead of adding several arrays of DSA_MAX_PORTS elements in the
mv88e6xxx_priv_state structure.

It currently only contains the port STP state.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 6320 family of switch chips has a second bank for statistics, but
is missing three statistics in the port registers. Generalise and
extend the code:

* adding a field to the statistics table indicating the bank/register
  set where each statistics is.
* add a function indicating if an individual statistics
  is available on this device
* calculate at run time the sset_count.
* return strings based on the available statistics of the device
* return statistics based on the available statistics of the device
* Add support for reading from the second bank.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DSA documentation specifies that each port must be capable of
forwarding frames to the CPU port. The last changes on bridging support
for the mv88e6xxx driver broke this requirement for non-bridged ports.

So as for the bridged ports, reserve a few VLANs (4000+) in the switch
to isolate ports that have not been bridged yet.

By default, a port will be isolated with the CPU and DSA ports. When the
port joins a bridge, it will leave its reserved port. When it is removed
from a bridge, it will join its reserved VLAN again.

Fixes: 5fe7f680 ("net: dsa: mv88e6xxx: fix hardware bridging")
Reported-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Frames with DSA headers passing to/from the CPU were taking place in the
MAC learning on these ports, resulting in incorrect ATU entries. Disable
learning on these ports.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All the mv88e6xxx drivers use the exact same code in their probe
function to lookup the switch name given its ID. Thus introduce a
mv88e6xxx_switch_id structure and a mv88e6xxx_lookup_name function in
the common mv88e6xxx code.

In the meantime make __mv88e6xxx_reg_{read,write} static since we do not
need to expose these low-level r/w routines anymore.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify DSA by pushing the switchdev objects for VLAN add and delete
operations down to its drivers. Currently only mv88e6xxx is affected.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is preferable to have a common debugfs interface for DSA or switchdev
instead of a driver specific one. Thus remove the mv88e6xxx debug code.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that port_fdb_dump is implemented and even simpler, get rid of
port_fdb_getnext.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the port_fdb_dump DSA operation.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Playing with the VLAN map of every port to implement "hardware bridging"
in the 88E6352 driver was a hack until full 802.1Q was supported.

Indeed with 802.1Q port mode "Disabled" or "Fallback", this feature is
used to restrict which output ports an input port can egress frames to.

A Linux bridge is an untagged VLAN. With full 802.1Q support, we don't
need this hack anymore and can use the "Secure" strict 802.1Q port mode.

With this mode, the port-based VLAN map still needs to be configured,
but all the logic is VTU-centric. This means that the switch only cares
about rules described in its hardware VLAN table, which is exactly what
Linux bridge expects and what we want.

Note also that the hardware bridging was broken with the previous
flexible "Fallback" 802.1Q port mode. Here's an example:

Port0 and Port1 belong to the same bridge. If Port0 sends crafted tagged
frames with VID 200 to Port1, Port1 receives it. Even if Port1 is in
hardware VLAN 200, but not Port0, Port1 will still receive it, because
Fallback mode doesn't care about invalid VID or non-member source port.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we configure a switch chip through a Linux bridge, and a bridge is
implemented as a VLAN, there is no need for per-port FID anymore.

This patch gets rid of this and simplifies the driver code since we can
now directly map all 4095 FIDs available to all VLANs.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With 88E6352 and similar switch chips, each port has a map to restrict
which output port this input port can egress frames to.

The current driver code implements hardware bridging using this feature,
and assigns to a bridge group the FID of its first member.

Now that 802.1Q is fully implemented in this driver, a Linux bridge
which is a simple untagged VLAN, already gets its own FID.

This patch gets rid of the per-bridge FID and explicits the usage of the
port based VLAN map feature.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For consistency with the FDB add operation, propagate the
switchdev_obj_port_fdb structure in the DSA drivers.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the prepare phase is pushed down to the DSA drivers, propagate
it to the port_fdb_add function.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>