NetXen: Fix PPC architecture specific bugs
Fixes some issues seen on Big endian machines.

Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

NetXen: Port Swap feature
This patch will allow a port numbers on the card to be swapped in
host driver. This feature is applicable to cards having more than
1 port.

Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

NetXen: Remove 2 redundant macro definitions from header file.

Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

NetXen: Fix the multi PCI function for cards with more than 2 ports.
This patch fixes the working of multi PCI capable driver on cards with
more than 2 ports by adding the addresses for their rings and sizes.

Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

NetXen: Removal of redundant function call parameters and bug fixes.
This patch will remove the redundant paramters which were being passed to
many functions since now adapter->portnum can be used.
Signed-off-by: NMithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

NetXen: Make driver use multiple PCI functions.
This patch will make NetXen driver work with multiple PCI functions. This will
make the usage of memory resources as well as interrupts more independent
among different functions which results in better throughput. This change has
been done after the multiport support is added in firmware.

Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

I was going to say that eepro100's speedo_rx_link() does the same DMA
abuse as e100, but then I noticed one little detail: eepro100 sets  both
EL (end of list) and S (suspend) bits in the RFD as it chains it  to the
RFD list.  e100 was only setting the EL bit.  Hmmm, that's  interesting.
That means that if HW reads a RFD with the S-bit set,  it'll process
that RFD and then suspend the receive unit.  The  receive unit will
resume when SW clears the S-bit.  There is no need  for SW to restart
the receive unit.  Which means a lot of the receive  unit state tracking
code in the driver goes away.

So here's a patch against 2.6.14.  (Sorry for inlining it; the mailer
I'm using now will mess with the word wrap).  I can't test this on
XScale (unless someone has an e100 module for Gumstix :) .  It should
be doing exactly what eepro100 does with RFDs.  I don't believe this
change will introduce a performance hit because the S-bit and EL-bit  go
hand-in-hand meaning if we're going to suspend because of the S- bit,
we're on the last resource anyway, so we'll have to wait for SW  to
replenish.
(cherry picked from 29e79da9495261119e3b2e4e7c72507348e75976 commit)

Using any of the IEEE80211_DEBUG_XXXX macros in any ieee80211_crypt
routine built as a module results in a missing global for
'ieee80211_debug_level'.  The fix is to export the symbol in ieee80211.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add kernel-doc notation to drivers/net/mii.c functions.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

drivers/net/ibmveth.c:96:46: error: marked inline, but without a definition
drivers/net/ibmveth.c:96: warning: 'ibmveth_rxq_harvest_buffer' declared inline after being called
drivers/net/ibmveth.c:96: warning: previous declaration of 'ibmveth_rxq_harvest_buffer' was here

Just let the compiler decide, as it happens gcc 4.~ inlines it anyway.

drivers/net/ibmveth.c:957:71: warning: Using plain integer as NULL pointer
drivers/net/ibmveth.c:964:85: warning: Using plain integer as NULL pointer

Split the long lines as well, ugly, but < 80 columns.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The ucc_geth_memclean function can be called before the Tx BD rings, Rx
BD rings and associated socket buffers are allocated (for example if
ucc_fast_init fails). The current code doesn't check if p_tx_bd_ring[i]
is null, generating a kernel panic when trying to free the associated
socket buffers.

The function can also fail when accessing the uninitialized list_head
structures ugeth->group_hash_q and ugeth->ind_hash_q. In the current
implementation the list heads are initialized only when
maxGroupAddrInHash and maxIndAddrInHash are positive values, although I
think it's better to always initialize them.
Signed-off-by: NIonut Nicu <ionut.nicu@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Transmit on Demand: Fix spelling in config option, and make it actually enable TOD.
Signed-off-by: NMichael Reiss <michael.f.reiss@freescale.com>
Signed-off-by: NMichael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The rx interrupt coalescing table alignment was "guessed" to be 4,
but should be 64. The size should be 8 * number of queues + 4.
Verified in the MPC8323E manual.
Signed-off-by: NMichael Barkowski <Michael.Barkowski@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Based partly on the gianfar driver, this patch fixes several
bugs which were causing NAPI to be completely unusable.
* An IRQ is still needed in NAPI, to kick off NAPI task,
  and for Tx processing.  Request the IRQ.
* If rx_work_limit = 0 we are not complete.
* While running Rx NAPI processing we must mask Rx events,
  including Rx busy.
* ucc_geth_rx function does not need a lock.
  Could lead to deadlock in NAPI case.
* There's no need to loop reading ucce multiple times in the ISR,
  so while adding the call to schedule NAPI which was not there,
  simplify the event processing into if-else format.
* Rx Busy now kicks off NAPI processing, while still
  being counted as an error.
Signed-off-by: NMichael Reiss <michael.f.reiss@freescale.com>
Signed-off-by: NMichael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

migrate ucc_geth to use the common phylib code.

There are several side effects from doing this:

o deprecate 'interface' property specification present
  in some old device tree source files in
  favour of a split 'max-speed' and 'interface-type'
  description to appropriately match definitions
  in include/linux/phy.h.  Note that 'interface' property
  is still honoured if max-speed or interface-type
  are not present (backward compatible).
o compile-time CONFIG_UGETH_HAS_GIGA is eliminated
  in favour of probe time speed derivation logic.
o adjust_link streamlined to only operate on maccfg2
  and upsmr.r10m, instead of reapplying static initial
  values related to the interface-type.
o Addition of UEC MDIO of_platform driver requires
  platform code add 'mdio' type to id list
  prior to calling of_platform_bus_probe (separate patch).
o ucc_struct_init introduced to reduce ucc_geth_startup
  complexity.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The RGMII spec allows compliance for devices that implement an internal
delay on TXC or RXC inside the transmitter.  This patch adds an RGMII_ID
definition to support RGMII-ID devices in the phylib.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There are messages arising from ieee80211_crypt that spam the logs
of casual users. These are changed to be logged only if the user
specifically requests the IEEE80211_DEBUG_DROP messages. In either
case, the error/drop count is incremented.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tested by Christoph Sager and Tomas Klas

zd1211b chip 0586:3412 v4810 high 00-13-49 AL7230B_RF pa0 g----
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for some new ZD1211B devices which ship with
the AL7230B RF.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change allows RF drivers to provide their own 6M band edge patching
implementation, while providing a generic implementation shared by most
currently supported RF's.

The upcoming ZD1211B/AL7230B code will use this to define its own
patching function, which is different from the other RF configurations.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The vendor driver only does the CR123 write for non-USB devices (which
don't exist on the consumer market)
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add ADLINK 345 CF card into hostap_cs

product info: "ADLINK 345 CF"
 manfid 0xd601, 0x0005
Signed-off-by: NMarcin Juszkiewicz <openembedded@hrw.one.pl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IEEE80211_RADIOTAP_FCS is obsolete and should not be used.  It's no
longer defined.  Remove it from the comment too.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch implements the changes in the specifications for
2050radio_init that were recently posted.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On Fri, Mar 30, 2007 at 01:05:59AM -0700, Andrew Morton wrote:
>...
> Changes since 2.6.21-rc5-mm2:
>...
>  git-netdev-all.patch
>...
>  git trees
>...

This patch makes the needlessly global PHY_DEVICES[] static.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Changed the maintainers for the S2io driver.
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Replacing with time_after in drivers/net/eexpress.c
Applies and compiles clean on latest tree.Not tested.
Signed-off-by: NShani Moideen <shani.moideen@wipro.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch includes:
- removal of unused fields in structs
- ethtool statistics cleanup
- removes unsed functionality from send path
Signed-off-by: NJan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There is no good reason for the asymmetry in the parameters of
eth_port_uc_addr_get() and eth_port_uc_addr_set().  Make them
symmetric.  Remove some gratuitous block comments while we're here.
Signed-off-by: NGabriel Paubert <paubert@iram.es>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This PHY support patch was written by Benjamin Li.
Signed-off-by: NBenjamin Li <benjamin.li@qlogic.com>
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The baycom_ser_fdx driver did not allow i/o ports >= 0x1000.  Now that
there are pci cards (with rs232 ports) which use for example 0xb800 this
limit should not exists.

Also, for non kernel coders find the cause of problems was challenging so I
added extra logging.
Signed-off-by: NFolkert van Heusden <folkert@vanheusden.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

strlcpy already accounts for the trailing zero in its length
computation, so there is no need to substract one to the buffer size.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Cc: Thomas Klein <osstklei@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Tested by TiCPU on irc

zd1211 chip 13b1:001e v4802 high 00-14-bf AL2230_RF pa0 g---
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using monitor mode, Johannes Berg observed out that lots of corrupted
and otherwise invalid frames were being passed to the host.

When in monitor mode we were disabling the hardware filtering here, but
this is not how monitor mode should work.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a backport of Helge Deller's recent patch for wireless-dev.git
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After 13 years of use, it looks like my email address is finally going
to disappear. While this is likely to drop the amount of incoming spam
greatly ;-), it may also affect more appropriate messages, so let's
update my email address in various places. In addition, Host AP mailing
list is subscribers-only and linux-wireless can also be used for
discussing issues related to this driver which is now shown in
MAINTAINERS.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>