Extend the parameters in the firmware callback so it can be called
upon success and failure. This allows the caller to properly clear
all resources in the failure path. Right now the error code is
always zero, ie. success.

Cc: stable@vger.kernel.org # 4.9.x-
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For SDIO the alignment requirement for transfers from device to host
is configured in firmware. This configuration is limited to minimum
of 4-byte alignment. However, this is not correct for platforms using
64-bit DMA when the minimum alignment should be 8 bytes. This issue
appeared when the ALIGNMENT definition was set according the DMA
configuration. The configuration in firmware was not using that macro
defintion, but a hardcoded value of 4. Hence the driver reported
alignment failures for data coming from the device and causing
transfers to fail.

Fixes: 6e84ab60 ("brcmfmac: properly align buffers on certain platforms
Reported-by: NHans de Goede <hdegoede@redhat.com>
Tested-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Have proper request id filled in the SCHED_SCAN_RESULTS and
SCHED_SCAN_STOPPED notifications toward user-space by having the
driver provide it through the api.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

cfg80211_roamed() and cfg80211_roamed_bss() take the same arguments
except that cfg80211_roamed() requires the BSSID and
cfg80211_roamed_bss() requires the bss entry.

Unify the two functions by using a struct for driver initiated
roaming information so that either the BSSID or the bss entry can be
passed as an argument to the unified function.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
[modified the ath6k, brcm80211, rndis and wlan-ng drivers accordingly]
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
[modify brcmfmac to remove the useless cast, spotted by Arend]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

For multiple scheduled scan support the driver needs to know which
scheduled scan request is being stopped. Pass the request id in the
.sched_scan_stop() callback.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch implements the idea to have multiple scheduled scan requests
running concurrently. It mainly illustrates how to deal with the incoming
request from user-space in terms of backward compatibility. In order to
use multiple scheduled scans user-space needs to provide a flag attribute
NL80211_ATTR_SCHED_SCAN_MULTI to indicate support. If not the request is
treated as a legacy scan.

Drivers currently supporting scheduled scan are now indicating they support
a single scheduled scan request. This obsoletes WIPHY_FLAG_SUPPORTS_SCHED_SCAN.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
[clean up netlink destroy path to avoid allocations, code cleanups]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The driver was making changes to the skb_header without
ensuring it was writable (i.e. uncloned).
This patch also removes some boiler plate header size
checking/adjustment code as that is also handled by the
skb_cow_header function used to make header writable.
Signed-off-by: NJames Hughes <james.hughes@raspberrypi.org>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The incoming skb header may be resized if header space is
insufficient, which might change the data adddress in the skb.
Ensure that a cached pointer to that data is correctly set by
moving assignment to after any possible changes.
Signed-off-by: NJames Hughes <james.hughes@raspberrypi.org>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The fwsignal module is only referenced by the bcdc module and part of the
bcdc protocol. So only build it when CONFIG_BRCMFMAC_PROTO_BCDC is selected.

Fixes: acf8ac41 ("brcmfmac: remove reference to fwsignal data from struct brcmf_pub")
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When receiving pno results there may be duplicate channels and/or
ssids. Assure each is added only once when preparing the internal
escan request.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Checking whether the address of an array element is null is bogus
so removing it.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Assure the event data buffer is long enough to hold the array
of netinfo items and that SSID length does not exceed the maximum
of 32 characters as per 802.11 spec.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The fwsignal module is part of the bcdc protocol and as such does
its instance data is not needed in core structure. Moving it into
struct brcmf_bcdc instead.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When brcmf_fws_add_interface() is called the struct brcmf_if::fws_desc
field is initialized regardless the state of the fwsignal functionality,
ie. the fcmode. This is not needed when fcmode is NONE, which is the
default mode.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is a non-functional change to align the fwsignal module to
the naming pattern used throughout the driver.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Systems with 64 bit DMA at least partially require buffers to be used
for DMA to be 8-byte-aligned. One example is Amlogic Meson GX.
Switching the MMC/SDIO driver for this platform to SG DMA mode
resulted in problems due to unaligned buffers.

Fortunately the brcmfmac driver has a global define for the alignment.
Changing it to 8 fixed the issues with Meson GX.
Suggested-by: NHelmut Klein <hgkr.klein@gmail.com>
Tested-by: NHelmut Klein <hgkr.klein@gmail.com>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Instead passing both flags, which can be NULL, and vif_params,
which are never NULL, move the flags into the vif_params and
use BIT(0), which is invalid from userspace, to indicate that
the flags were changed.

While updating all drivers, fix a small bug in wil6210 where
it was setting the flags to 0 instead of leaving them unchanged.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In brcmf_pno_start_sched_scan() a local variable is declared and
assigned for struct brcmu_d11inf. However, there is no other reference
to it so it is unnecessary.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In brcmf_pcie_suspend() we inform the firmware on the device that
it will enter in D3 state. Before this is done we already bring down
the bus state. However, When entering D3 fails we abort the suspend
and the bus state need to be restored.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

To support network namespace the driver must assure all created
network interfaces are in the same namespace as the wiphy instance
and flag the support using WIPHY_FLAG_NETNS_OK.

Verified using two terminals:

 Terminal 1			Terminal 2
 --------------------------	---------------------------------
 # ip netns add brcm-wifi	# iw dev
				phy#0
					Interface wlan3
						ifindex 11
						wdev 0x1
 # ip netns exec brcm-wifi bash
 # iw dev
 # echo $$
 20337			# iw phy0 set netns 20337
 # iw dev
 phy#0
	Interface wlan3
		ifindex 11
		wdev 0x2
 # iw phy0 interface add wl3.ap type __ap
 # iw dev
 phy#0
	Interface wl3.ap
		ifindex 2
		wdev 0x3
	Interface wlan3
		ifindex 11
		wdev 0x2
				# iw dev
 # iw phy0 set netns 1
 # iw dev
				# iw dev
				phy#0
					Interface wl3.ap
						ifindex 2
						wdev 0x5
					Interface wlan3
						ifindex 11
						wdev 0x4

Note:
	increasing wdev identifier above indicates issue in
	cfg80211 which is addressed separately.
Tested-by: NMark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Move brcmf_fws_deinit into brcmf_proto_bcdc_detach since it is a bcdc
exclusive feature.
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Reviewed-by: NArend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Create a new protocol layer interface brcmf_proto_init_cb for protocol
layer to finish initialzation after core module components(fweh and
etc.) are initialized.
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Reviewed-by: NArend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

These files all use functions declared in interrupt.h, but currently rely
on implicit inclusion of this file (via netns/xfrm.h).

That won't work anymore when the flow cache is removed so include that
header where needed.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A use-after-free was found using KASAN. In brcmf_p2p_del_if() the virtual
interface is removed using call to brcmf_remove_interface(). After that
the virtual interface instance has been freed and should not be referenced.
Solve this by storing the nl80211 iftype in local variable, which is used
in a couple of places anyway.

Cc: stable@vger.kernel.org # 4.10.x, 4.9.x
Reported-by: NDaniel J Blueman <daniel@quora.org>
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Create a new protocol interface function brcmf_proto_reset_if for core
module to notify protocol layer when interface role changes.
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Create a new protocol interface function brcmf_proto_del_if for core
module to notify protocol layer upon interface deletion.
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

fwsignal is only used by bcdc. Create a new protocol interface function
brcmf_proto_add_if for core module to notify protocol layer upon a new
interface is created.
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

brcmf_txcomplete is invoked by sdio and usb bus module which are using
bcdc protocol. So move it from core module into bcdc layer.
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

brcmf_txflowblock is invoked by sdio and usb bus module which are using
bcdc protocol. This patch makes it a bcdc API instead of a core module
function.
Reviewed-by: NArend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If a scan gets aborted BRCMF_SCAN_STATUS_BUSY gets cleared in
cfg->scan_status and when we receive an abort event from the firmware
the BRCMF_SCAN_STATUS_BUSY check in the cfg80211_escan_handler will
trigger resulting in multiple errors getting logged.

Check for a status of BRCMF_E_STATUS_ABORT and in this case simply
cleanly exit the cfg80211_escan_handler. This also avoids a
BRCMF_E_STATUS_ABORT event arriving after a new scan has been started
causing the new scan to complete prematurely without any data.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The country code gets set to "00" by default at boot, ignore this
rather then logging an error about it.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Using pr_err for things which are not errors is a bad idea. E.g. it
will cause the plymouth bootsplash screen to drop back to the text
console so that the user can see the error, which is not what we
normally want to happen.

Instead add a new brcmf_info macro and use that.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

So far we were attaching BRCMF_E_PSM_WATCHDOG event listener in
brcmf_debug_attach which gets compiled only with CONFIG_BRCMDBG. This
event means something went wrong and firmware / hardware usually can't
be expected to work (reliably).

Such a problem is significant for user experience so I believe we should
print an error unconditionally (even with debugging disabled). What can
be indeed optional is dumping bus memory as this is clearly part of
debugging process.

In the future we may also try to extend this listener by trying to
recover from the error or at least signal it to the cfg80211.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.

Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.

Include the new header in the files that are going to need it.
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.

Use BUILD_BUG_ON in a couple ATM drivers.

In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement.  Hopefully this patch inspires
someone else to trim vsprintf.c more.

Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Instead of using a private copy of struct net_device_stats in struct
brcm_if, use stats from struct net_device.  Also remove the now
unnecessary .ndo_get_stats function.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Now we always have __brcmf_err function we can do perfectly fine with
just one macro.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This will allow extending code and using more detailed messages e.g.
with the help of dev_err.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This allows simplifying the code by adding a simple IS_ENABLED check for
CONFIG_BRCMDB symbol.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This new helper reads extra frequency limits specified in DT and
disables unavailable chanels. This is useful for devices (like home
routers) with chipsets limited e.g. by board design.

In order to respect info read from DT we simply need to check for
IEEE80211_CHAN_DISABLED bit when constructing channel info.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>