The platform data is used not only by wlcore-based drivers, but also
by wl1251.  Move it up in the directory hierarchy to reflect this.

Additionally, make it truly optional.  At the moment, disabling
platform data while wl1251_sdio or wlcore_sdio are enabled doesn't
work, but it will be necessary when device tree support is
implemented.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>

The platform devices can be created by both wlcore_sdio and
wlcore_spi.  Theoretically, if both are connected to the same board,
there will be a conflict.
Reported-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Just a small cleanup to use the pointer provided by wlcore_pdev_data
instead of using a separate pointer then copying.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We can't pass pointers from the platform data to the modules, because
with DT it cannot be done.  Those pointers are not set by the board
files anyway.  It's the bus modules that set them, so they can be
safely removed from the platform data without changing any board
files.

Create a new structure that the bus modules pass to wlcore.  This
structure contains the if_ops pointers and a pointer to the actual
platform data.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>

There is no platform-specific set_power method anymore.  Power setting
is done in the bus modules (wlcore_sdio and wlcore_spi).
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>

The PLT firmware used by wl12xx for calibration always has the same
version number as the single-role firmware.

Currntly the driver rejects the PLT firmware since anything that is
not single-role uses the multi-role version.  Fix this by using the
single-role version for everything except multi-role.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Whe this driver is built with "make W=1", the following warnings are output:

drivers/net/wireless/rtlwifi/rtl8723ae/fw.c:515:5: warning: variable ‘own’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/hal_btc.c:1436:5: warning: variable ‘bt_retry_cnt’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/hw.c:706:6: warning: variable ‘reg_ratr’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/hw.c:2033:41: warning: variable ‘cur_rfstate’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:620:23: warning: variable ‘radiob_arraylen’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:619:7: warning: variable ‘radiob_array_table’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:617:7: warning: variable ‘rtstatus’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:1534:6: warning: variable ‘bbvalue’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:1716:6: warning: variable ‘reg_ecc’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:1715:61: warning: variable ‘reg_ec4’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:1715:34: warning: variable ‘reg_eac’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c:247:6: warning: variable ‘psaddr’ set but not used [-Wunused-but-set-variable]
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

when this driver is built with "make W=1", the following warning is printed:

drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1058:5: warning: comparison is always false due to limited range of data type [-Wtype-limits]
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When this driver is built with "make W=1", the following warning is output:

drivers/net/wireless/rtlwifi/rtl8192cu/sw.c:56:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When this driver is built with "make W=1", the following warning occurs:

drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:907:4: warning: comparison is always false due to limited range of data type [-Wtype-limits]
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Building this driver with "make W=1" results in the following 2 warnings:

drivers/net/wireless/rtlwifi/usb.c:829:21: warning: variable ‘urb_list’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/usb.c:828:23: warning: variable ‘skb_list’ set but not used [-Wunused-but-set-variable]
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Many warnings like the following arise from a build with W=1 on the
make line:

warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]

Changing the overall debug level storage from unsigned to signed fixes these.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

0x1814,0x359f is a RT3592 802.11a/b/g/n 2x2 WiFi Adapter
support added by 872834df

Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Leaving the unused variables ath_mci_cleanup causes build warnings.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The relay file depends on relayfs. Trying to close this file without having
ATH9K_DEBUGFS (and therefore RELAY) activated causes build failures.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code is only used when ATH9K_DEBUGFS is activated and causes build warnings
when it is still compiled without user.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code can only be used when ATH9k_DEBUGFS is enabled an not when ATH_DEBUG
is activated. Still enabling it would cause build failures.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The spectral scan support activated through ATH9K_DEBUGFS depends on RELAY for
the kernel->userspace communication. Not activating RELAY causes build
failures.

The RELAY is added as select instead of depend to do it similar like
the only other user of RELAY: BLK_DEV_IO_TRACE
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

max_tx_buf_size is not used any more after reconfiguration of
tx buffer size has been removed.

Also add missing curr_tx_buf_size update while dumping debug info
via debugfs.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's observed that reconfiguration of tx buffer size before
association can cause data path failure in firmware after
associated. Although this is only found with PCIe cards, but
potentially it could happen with any other interfaces as well.

The tx buffer reconfiguration is not really useful in firmware.
Let's remove it for all interfaces.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath9k hardware reports whenever an frame was part
of an A-MPDU. MAC80211 already provides the necessary
API to pass this additional information along to
whomever needs it.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Devices were taken from Ralink Linux drivers:
- RT5370
0x043e, 0x7a32
0x043e, 0x7a42
0x0471, 0x2126
0x0471, 0x2180
0x0471, 0x2181
0x0471, 0x2182

Identify these ones:
0x04da, 0x23f6 in CONFIG_RT2800USB_RT53XX is a Panasonic device
0x07d1, 0x3c17 in RT2800USB_UNKNOWN is a RT3070
0x0586, 0x341a in RT2800USB_UNKNOWN is a RT3070

Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Handle pci_map_page() errors. This fixes "DMA-API: device driver failed
to check map error" warning.
Reported-by: NZdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is based on "iwlwifi: report A-MPDU status".
(12bf6f45)

Since the firmware will give us an A-MPDU bit and
only a single PHY information packet for all the
subframes in an A-MPDU, we can easily report the
minimal A-MPDU information for radiotap.

Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

This patch does a trivial refactor in mgmt_pending_foreach function.
It replaces list_for_each_safe by list_for_each_entry_safe, simplifying
the function.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch removes unneeded locking in hci_le_adv_report_evt. There
is no need to lock hdev before calling mgmt_device_found.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch reduces the critical section protected by sco_conn_lock in
sco_conn_ready function. The lock is acquired only when it is really
needed.

This patch fixes the following lockdep warning which is generated
when the host terminates a SCO connection.

Today, this warning is a false positive. There is no way those
two threads reported by lockdep are running at the same time since
hdev->workqueue (where rx_work is queued) is single-thread. However,
if somehow this behavior is changed in future, we will have a
potential deadlock.

======================================================
[ INFO: possible circular locking dependency detected ]
3.8.0-rc1+ #7 Not tainted
-------------------------------------------------------
kworker/u:1H/1018 is trying to acquire lock:
 (&(&conn->lock)->rlock){+.+...}, at: [<ffffffffa0033ba6>] sco_chan_del+0x66/0x190 [bluetooth]

but task is already holding lock:
 (slock-AF_BLUETOOTH-BTPROTO_SCO){+.+...}, at: [<ffffffffa0033d5a>] sco_conn_del+0x8a/0xe0 [bluetooth]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (slock-AF_BLUETOOTH-BTPROTO_SCO){+.+...}:
       [<ffffffff81083011>] lock_acquire+0xb1/0xe0
       [<ffffffff813efd01>] _raw_spin_lock+0x41/0x80
       [<ffffffffa003436e>] sco_connect_cfm+0xbe/0x350 [bluetooth]
       [<ffffffffa0015d6c>] hci_event_packet+0xd3c/0x29b0 [bluetooth]
       [<ffffffffa0004583>] hci_rx_work+0x133/0x870 [bluetooth]
       [<ffffffff8104d65f>] process_one_work+0x2bf/0x4f0
       [<ffffffff81050022>] worker_thread+0x2b2/0x3e0
       [<ffffffff81056021>] kthread+0xd1/0xe0
       [<ffffffff813f14bc>] ret_from_fork+0x7c/0xb0

-> #0 (&(&conn->lock)->rlock){+.+...}:
       [<ffffffff81082215>] __lock_acquire+0x1465/0x1c70
       [<ffffffff81083011>] lock_acquire+0xb1/0xe0
       [<ffffffff813efd01>] _raw_spin_lock+0x41/0x80
       [<ffffffffa0033ba6>] sco_chan_del+0x66/0x190 [bluetooth]
       [<ffffffffa0033d6d>] sco_conn_del+0x9d/0xe0 [bluetooth]
       [<ffffffffa0034653>] sco_disconn_cfm+0x53/0x60 [bluetooth]
       [<ffffffffa000fef3>] hci_disconn_complete_evt.isra.54+0x363/0x3c0 [bluetooth]
       [<ffffffffa00150f7>] hci_event_packet+0xc7/0x29b0 [bluetooth]
       [<ffffffffa0004583>] hci_rx_work+0x133/0x870 [bluetooth]
       [<ffffffff8104d65f>] process_one_work+0x2bf/0x4f0
       [<ffffffff81050022>] worker_thread+0x2b2/0x3e0
       [<ffffffff81056021>] kthread+0xd1/0xe0
       [<ffffffff813f14bc>] ret_from_fork+0x7c/0xb0

other info that might help us debug this:

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
                               lock(&(&conn->lock)->rlock);
                               lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
  lock(&(&conn->lock)->rlock);

 *** DEADLOCK ***

4 locks held by kworker/u:1H/1018:
 #0:  (hdev->name#2){.+.+.+}, at: [<ffffffff8104d5f8>] process_one_work+0x258/0x4f0
 #1:  ((&hdev->rx_work)){+.+.+.}, at: [<ffffffff8104d5f8>] process_one_work+0x258/0x4f0
 #2:  (&hdev->lock){+.+.+.}, at: [<ffffffffa000fbe9>] hci_disconn_complete_evt.isra.54+0x59/0x3c0 [bluetooth]
 #3:  (slock-AF_BLUETOOTH-BTPROTO_SCO){+.+...}, at: [<ffffffffa0033d5a>] sco_conn_del+0x8a/0xe0 [bluetooth]

stack backtrace:
Pid: 1018, comm: kworker/u:1H Not tainted 3.8.0-rc1+ #7
Call Trace:
 [<ffffffff813e92f9>] print_circular_bug+0x1fb/0x20c
 [<ffffffff81082215>] __lock_acquire+0x1465/0x1c70
 [<ffffffff81083011>] lock_acquire+0xb1/0xe0
 [<ffffffffa0033ba6>] ? sco_chan_del+0x66/0x190 [bluetooth]
 [<ffffffff813efd01>] _raw_spin_lock+0x41/0x80
 [<ffffffffa0033ba6>] ? sco_chan_del+0x66/0x190 [bluetooth]
 [<ffffffffa0033ba6>] sco_chan_del+0x66/0x190 [bluetooth]
 [<ffffffffa0033d6d>] sco_conn_del+0x9d/0xe0 [bluetooth]
 [<ffffffffa0034653>] sco_disconn_cfm+0x53/0x60 [bluetooth]
 [<ffffffffa000fef3>] hci_disconn_complete_evt.isra.54+0x363/0x3c0 [bluetooth]
 [<ffffffffa000fbd0>] ? hci_disconn_complete_evt.isra.54+0x40/0x3c0 [bluetooth]
 [<ffffffffa00150f7>] hci_event_packet+0xc7/0x29b0 [bluetooth]
 [<ffffffff81202e90>] ? __dynamic_pr_debug+0x80/0x90
 [<ffffffff8133ff7d>] ? kfree_skb+0x2d/0x40
 [<ffffffffa0021644>] ? hci_send_to_monitor+0x1a4/0x1c0 [bluetooth]
 [<ffffffffa0004583>] hci_rx_work+0x133/0x870 [bluetooth]
 [<ffffffff8104d5f8>] ? process_one_work+0x258/0x4f0
 [<ffffffff8104d65f>] process_one_work+0x2bf/0x4f0
 [<ffffffff8104d5f8>] ? process_one_work+0x258/0x4f0
 [<ffffffff8104fdc1>] ? worker_thread+0x51/0x3e0
 [<ffffffffa0004450>] ? hci_tx_work+0x800/0x800 [bluetooth]
 [<ffffffff81050022>] worker_thread+0x2b2/0x3e0
 [<ffffffff8104fd70>] ? busy_worker_rebind_fn+0x100/0x100
 [<ffffffff81056021>] kthread+0xd1/0xe0
 [<ffffffff81055f50>] ? flush_kthread_worker+0xc0/0xc0
 [<ffffffff813f14bc>] ret_from_fork+0x7c/0xb0
 [<ffffffff81055f50>] ? flush_kthread_worker+0xc0/0xc0
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch increments the management interface revision due to the
various fixes, improvements and other changes that have gone in lately.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

If a controller is powered on while the HCI_AUTO_OFF flag is set the
link security setting (HCI_LINK_SECURITY) might not be in sync with the
actual state of the controller (HCI_AUTH). This patch fixes the issue by
checking for inequality between the intended and actual settings and
sends a HCI_Write_Auth_Enable command if necessary.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch adds the necessary code for encoding a list of 128-bit UUIDs
into the EIR data.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch adds the necessary code for inserting a list of 32-bit UUIDs
into the EIR data.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

We will need to create three separate UUID lists in the EIR data (for
16, 32 and 128 bit UUIDs) so the code is easier to follow if each list
is generated in their own function.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The amount of data encoded so far in the create_eir() function can be
calculated simply through the difference between the data and ptr
pointer variables. The eir_len variable then becomes essentially
useless.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

There's no need to use two separate loops to generate a UUID list for
the EIR data. This patch merges the two loops previously used for the
16-bit UUID list generation into a single loop, thus simplifying the
code a great deal.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The UUID removal code can be simplified by using
list_for_each_entry_safe instead of list_for_each_safe.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The primary purpose of the UUIDs is to enable generation of EIR and AD
data. In these data formats the UUIDs are split into separate fields
based on whether they're 16, 32 or 128 bit UUIDs. To make the generation
of these data fields simpler this patch adds a type member to the
bt_uuid struct and assigns a value to it as soon as the UUID is added to
the kernel. This way the type doesn't need to be calculated each time
the UUID list is later iterated.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>