This patch aims to remove a use of the bond->lock for mutual exclusion
which will later allow easier migration to RCU of the users of this
functionality. We use RTNL as a synchronizing mechanism since it's
always held when send_peer_notif is set, and when it is decremented from
the notifier function. We can also drop some locking, and fix the
leakage of the send_peer_notif counter.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As Michael point out, We used to limit the max pending DMAs to get better cache
utilization. But it was not done correctly since it was one done when there's no
new buffers submitted from guest. Guest can easily exceeds the limitation by
keeping sending packets.

So this patch moves the check into main loop. Tests shows about 5%-10%
improvement on per cpu throughput for guest tx.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We used to poll vhost queue before making DMA is done, this is racy if vhost
thread were waked up before marking DMA is done which can result the signal to
be missed. Fix this by always polling the vhost thread before DMA is done.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, even if the packet length is smaller than VHOST_GOODCOPY_LEN, if
upend_idx != done_idx we still set zcopy_used to true and rollback this choice
later. This could be avoided by determining zerocopy once by checking all
conditions at one time before.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let vhost_add_used() to use vhost_add_used_n() to reduce the code
duplication. To avoid the overhead brought by __copy_to_user(). We will use
put_user() when one used need to be added.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We tend to batch the used adding and signaling in vhost_zerocopy_callback()
which may result more than 100 used buffers to be updated in
vhost_zerocopy_signal_used() in some cases. So switch to use
vhost_add_used_and_signal_n() to avoid multiple calls to
vhost_add_used_and_signal(). Which means much less times of used index
updating and memory barriers.

2% performance improvement were seen on netperf TCP_RR test.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

None of its caller use its return value, so let it return void.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data
using pci_dev instead of using dev_{get,set}_drvdata() with
&pdev->dev, so we can directly pass a struct pci_dev. This is
a purely cosmetic change.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data
using pci_dev instead of using dev_{get,set}_drvdata() with
&pdev->dev, so we can directly pass a struct pci_dev. This is
a purely cosmetic change.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.

Done via cocci script: (and a little typing)

$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
-	!compare_ether_addr(a, b)
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	compare_ether_addr(a, b)
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) == 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) != 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) == 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) != 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!!ether_addr_equal(a, b)
+	ether_addr_equal(a, b)
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLiu Junliang <liujunliang_ljl@163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SkyHawk-R can support VEB or VEPA mode.
This patch will allow the user to set/query this switch setting.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the amount of sent bytes reported to BQL by reporting the
number of bytes on wire in the xmit routine, and recording that
value for each skb in order to be correctly confirmed on Tx
confirmation cleanup.

Reporting skb->len to BQL just before exiting xmit is not correct
due to possible insertions of TOE block and alignment bytes in the
skb->data, which are being stripped off by the controller before
transmission on wire.  This led to mismatch of (incorrectly)
reported bytes to BQL b/w xmit and Tx confirmation, resulting in
Tx timeout firing, for the h/w tx timestamping acceleration case.

There's no easy way to obtain the number of bytes on wire in the Tx
confirmation routine, so skb->cb is used to convey that information
from xmit to Tx confirmation, for now (as proposed by Eric). Revived
the currently unused GFAR_CB() construct for that purpose.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When my 'ifup eth' script was fired multiple times and ran concurrent on
my laptop, for some obscure /etc scripting reason, it was revealed
that the store_enabled() function in netconsole doesn't handle it nicely,
as recorded by the Oops below (a syslog paste, but not mangled too much
to prevent from discerning the traceback).

On Linux 3.10.4, this patch seeks to remedy the problem, and it has been
running stable on my laptop for a few days.

[52608.609325] BUG: unable to handle kernel NULL pointer dereference at 00000000000003e0
[52608.609331] IP: [<ffffffff81532a17>] __netpoll_cleanup+0x27/0xe0
[52608.609339] PGD 15e51a067 PUD 15433e067 PMD 0
[52608.609343] Oops: 0000 [#1] SMP re firewire_ohci firewire_core crc_itu_t [last unloaded: kvm_intel]
[52608.609347] Modules linked in: kvm_intel tun vfat fat ppdev parport_pc parport fuse ipt_MASQUERADE usb_storage nf_conntrack_netbios_ns nf_conn [..garbled..]
[52608.609433] RAX: 0000000000000000 RBX: ffff880210bbcc68 RCX: 0000000000000000
[52608.609435] RDX: 0000000000000000 RSI: ffff8801ba447da0 RDI: ffff880210bbcc68
[52608.609437] RBP: ffff8801ba447e18 R08: 0000000000000000 R09: 0000000000000001
[52608.609439] R10: 000000000000000a R11: f000000000000000 R12: ffff880210bbcc68
[52608.609441] R13: ffff88020bc41000 R14: 0000000000000002 R15: 000000000000000200000000000
[52608.609443] FS:  00007f38d7bff740(0000) GS:ffff88021dc40000(0000) knlGS:0000000000000000
[52608.609446] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003300000000001427e0
[52608.609448] CR2: 00000000000003e0 CR3: 0000000154103000 CR4: 00000000001427e0
[52608.609450] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[52608.609452] netpoll: netconsole: local port 6665ess 10.0.0.27
[52608.609454] netpoll: netconsole: local IPv4 address 10.0.0.27
[52608.609456] netpoll: netconsole: interface 'em1'
[52608.609457] netpoll: netconsole: remote port 514ress 10.0.0.15
[52608.609459] netpoll: netconsole: remote IPv4 address 10.0.0.15:65:a8:9a:c7
[52608.609461] netpoll: netconsole: remote ethernet address 1c:6f:65:a8:9a:c7
[52608.609463] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[52608.609464] Stack:801ba447e08 ffff880210bbcc68 ffffffffffffffea ffff88020bc41000
[52608.609466]  ffff8801ba447e08 ffff880210bbcc68 ffffffffffffffea ffff88020bc41000
[52608.609471]  0000000000000002 0000000000000002 ffff8801ba447e38 ffffffff81532af4
[52608.609475]  0000000000000000 ffff880210bbcc00 ffff8801ba447e78 ffffffff81420e7c
[52608.609479] Call Trace:
[52608.609484]  [<ffffffff81532af4>] netpoll_cleanup+0x24/0x50
[52608.609489]  [<ffffffff81420e7c>] store_enabled+0x5c/0xe0
[52608.609492]  [<ffffffff81420abe>] netconsole_target_attr_store+0x2e/0x40
[52608.609498]  [<ffffffff811ff2a2>] configfs_write_file+0xd2/0x130
[52608.609503]  [<ffffffff81188f95>] vfs_write+0xc5/0x1f0
[52608.609506]  [<ffffffff81189482>] SyS_write+0x52/0xa0/0x10
[52608.609511]  [<ffffffff81628c2e>] ? do_page_fault+0xe/0x10
[52608.609516]  [<ffffffff8162d402>] system_call_fastpath+0x16/0x1b
[52608.609517] Code: 1f 44 00 00 0f 1f 44 00 00 55 48 89 e5 48 83 ec 30 4c 89 65 e0 48 89 5d d8 49 89 fc 4c 89 6d e8 4c 89 75 f0 4c 89 7d f8 48 8 [..garbled..]
[52608.609559] RIP  [<ffffffff81532a17>] __netpoll_cleanup+0x27/0xe0
[52608.609563]  RSP <ffff8801ba447de8>
[52608.609564] CR2: 00000000000003e0
[52608.609567] ---[ end trace d25ec343349b61d2 ]---
Signed-off-by: NDan Aloni <alonid@postram.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This corrects an oversight when r8a7790 support was added to sh_eth.
Signed-off-by: NKouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NKouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Store VID in ->vlan_id (if any), and remove the useless ->tag.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We're using it currently to verify if we have vlans before getting the tag
from the skb we're about to send. It's useless because the vlan_get_tag()
verifies if the skb has the tag (and returns an error if not), and we can
receive tagged skbs only if we *already* have vlans.

Plus, the current RCUed implementation is kind of useless anyway - the we
can remove the last vlan in the moment we return from the function.

So remove the only usage of it and the whole function.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the VIRTIO_NET_F_GUEST_CSUM virtio feature is available, the guest
does not have to calculate the checksums on all received packets. This
is pretty much the same feature as RX checksum offloading on real
network cards, so the virtio-net driver should report this by setting
the NETIF_F_RXCSUM flag. When the user now runs "ethtool -k", he or she
can see whether the virtio-net interface has to calculate RX checksums
or not.
Signed-off-by: NThomas Huth <thuth@linux.vnet.ibm.com>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A device inheriting a random or set address should reflect this in
its addr_assign_type.

Cc: Forest Bond <forest@alittletooquiet.net>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A device inheriting a random or set address should reflect this in
its addr_assign_type.
Acked-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A device inheriting a random or set address should reflect this in
its addr_assign_type.

Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A device inheriting a random or set address should reflect this in
its addr_assign_type.
Acked-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A device inheriting a random or set address should reflect this in
its addr_assign_type.

Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A device inheriting a random or set address should reflect this in
its addr_assign_type.

Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fengguang reported a compile warning:

   drivers/net/vxlan.c: In function 'vxlan6_xmit_skb':
   drivers/net/vxlan.c:1352:3: error: implicit declaration of function 'csum_ipv6_magic' [-Werror=implicit-function-declaration]
   cc1: some warnings being treated as errors

this patch fixes it.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It should be IPPROTO_UDP.
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an embedded switch per physical port on the adapter.
Add support for enabling and disabling the embedded switch
on per port basis.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Removed unused and unnecessary members from qlc_83xx_fw_info
  structure.
o Made fw_info member of qlcnic_hardware_context as a pointer to
  qlc_83xx_fw_info structure.
o Added a member fw_file_name to qlc_83xx_fw_info structure which
  will hold the name of firmware image file name.
Signed-off-by: NPratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Generic AER callback handlers will make use of qlcnic_hardware_ops structure
  to call adapter specific handlers.
Signed-off-by: NPratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

-Use CAMRAM register to store firmware dump state in adapter
 instead of maintaining it in each function driver separately.
-Return appropriate error code on failure
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Remove inline keyword from function prototypes wherever it is not appropriate.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o PF driver should not indicate PVID configuration to VF driver.
  As adapter supports VLAN stripping, VF driver should stay agnostic
  to any PVID configuration.

o Return "QLC_NO_VLAN_MODE(= 0)" to VFD when PVID is configured.
  VF driver should be in no VLAN configuration mode.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the IPv6 version of "arp_reduce", ndisc_send_na()
will be needed.

Cc: David S. Miller <davem@davemloft.net>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>