Relocate get_ata_protocol() to a common location, as future hw versions
will require it.  Also rename with "hisi_sas_" prefix for consistency.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently hisi_hba.lock is locked to deliver and receive a command
to/from any hw queue. This causes much contention at high data-rates.

To boost performance, lock on a per queue basis for sending and
receiving commands to/from hw.

Certain critical regions still need to be locked in the delivery and
completion stages with hisi_hba.lock.

New element hisi_sas_device.dq is added to store the delivery queue for
a device, so it does not need to be needlessly re-calculated for every
task.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently hisi_sas_device.device_id is a u64. This can create a problem
in selecting the queue for a device, in that this code does a 64b
division on device id. For some 32b systems, 64b division is slow and
the lib reference must be explicitly included.

The device id does not need to be 64b in size, so, as a solution, just
make as an int.

Also, struct hisi_sas_device elements are re-ordered to improve packing
efficiency.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

We need to check for timeout before task status, or the task will be
mistook as completed internal abort command.  Also add protection for
sas_task.task_state_flags in hisi_sas_tmf_timedout().
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add null check before indirectly dereferencing pointer task->lldd_task
in statement u32 tag = slot->idx;

Addresses-Coverity-ID: 1373843
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Move scsi_remove_host call into sas_remove_host and remove it from SAS
HBA drivers, so we don't mess up the ordering. This solves an issue with
double deleting sysfs entries that was introduced by the change of sysfs
behaviour from commit bcdde7e2 ("sysfs: make __sysfs_remove_dir()
recursive").

[mkp: addressed checkpatch complaints]
Signed-off-by: NJohannes Thumshirn <jthumshirn@suse.de>
Suggested-by: NChristoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: James Bottomley <jejb@linux.vnet.ibm.com>
Cc: Jinpu Wang <jinpu.wang@profitbricks.com>
Cc: John Garry <john.garry@huawei.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJinpu Wang <jinpu.wang@profitbricks.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For 1 bit ECC errors, those errors can be recovered by hw. But for
multi-bits ECC and AXI errors, there are something wrong with whole
module or system, so try reset the controller to recover those errors
instead of calling panic().
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If a TMF timeouts (maybe due to unlikely scenario of an expander being
unplugged when TMF for remote device is active), when we eventually try
to free the slot, we crash as we dereference the slot's task, which has
already been released.

As a fix, add checks in the slot release code for a NULL task.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch is a workaround for a SoC bug where an internal abort command
may timeout. In v2 hw, the channel should become idle in order to finish
abort process. If the target side has been sending HOLD, host side
channel failed to complete the frame to send, and can not enter the idle
state. Then internal abort command will timeout.

As this issue is only in v2 hw, we deal with it in the hw layer.  Our
workaround solution is: If abort is not finished within a certain period
of time, we will check HOLD status. If HOLD has been sending, we will
send break command.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds a workaround solution for a SoC bug which may cause SoC
logic fatal error when disabling a PHY.  Then we find internal abort IO
timeout may occur, and the controller IO breakpoint may be corrupted.

We work around this SoC bug by optimizing the flow of disabling a PHY.
Signed-off-by: NXiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch provides a workaround a SoC bug where SATA IPTTs for
different devices may conflict.

The workaround solution requests the following:
1. SATA device id must be even and not equal to SAS IPTT.
2. SATA device can not share the same IPTT with other SAS or
   SATA device.

Besides we shall consider IPTT value 0 is reserved for another SoC bug
(STP device open link at firstly after SAS controller reset).

To sum up, the solution is: Each SATA device uses independent and
continuous 32 even IPTT from 64 to 4094, then v2 hw can only support 63
SATA devices.  All SAS device(SSP/SMP devices) share odd IPTT value from
1 to 4095.
Signed-off-by: NXiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

After resetting the controller, the process of scanning SATA disks
attached to an expander may fail occasionally. The issue is that the
controller can't close the STP link created by target if the max link
time is 0.

To workaround this issue, we reject STP link after resetting the
controller, and change the corresponding PHY to accept STP link only
after receiving data.

We do this check in cq interrupt handler. In order not to reduce
efficiency, we use an variable to control whether we should check and
change PHY to accept STP link.

The function phys_reject_stp_links_v2_hw() should be called after
resetting the controller.

The solution of another SoC bug "SATA IO timeout", that also uses the
same register to control STP link, is not effective before the PHY
accepts STP link.
Signed-off-by: NXiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Removing the 'select SCSI_SAS_LIBSAS' statement in Kconfig resulted in a
link failure in configurations that have hisi_sas built-in but libsas as
a loadable module:

drivers/scsi/built-in.o: In function `hisi_sas_scan_finished':
hisi_sas_main.c:(.text+0x37ce9): undefined reference to `sas_drain_work'
drivers/scsi/built-in.o: In function `hisi_sas_slave_configure':
hisi_sas_main.c:(.text+0x37d17): undefined reference to `sas_slave_configure'
hisi_sas_main.c:(.text+0x37d40): undefined reference to `sas_change_queue_depth'
drivers/scsi/built-in.o: In function `hisi_sas_remove':

All other libsas users have the 'select' statement, so we should do the
same here for consistency. For all I can tell, the patch that added the
sata softreset does not actually introduce a dependency on SCSI_SAS_ATA
but instead adds calls into libata itself, so we can express that with a
more specific dependency.

We cannot have 'select SCSI_SAS_LIBSAS; depends on SCSI_SAS_ATA' as that
would cause a dependency loop.

Fixes: 7c594f04 ("scsi: hisi_sas: add softreset function for SATA disk")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

It appears that a break in the TRANS_TX_OPEN_CNX_ERR_NO_DESTINATION case
got accidentally removed in an earlier commit, as it stands, the
ts->stat and ts->open_rej_reason are being updated twice for this case
which looks incorrect.  Fix this by adding in the missing break
statement.

Detected by CoverityScan, CID#1422110 ("Missing break in switch")

Fixes: 634a9585 ("scsi: hisi_sas: process error codes according to their priority")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add helper function is_sata_phy_v2_hw() to judge whether the attached
device is SATA disk for a root PHY.
Signed-off-by: NXiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When SMP IO is sent, sas_protocol_ata couldn't judge whether the disk is
SATA or SAS disk.  So use dev_is_sata to identify SATA or SAS disk.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Unless we actually get some sort of failure in hisi_sas_lu_reset(),
don't print a message.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When an SMP task timeouts, it will call lldd_abort_task to release the
associated slot, and then will release the sas_task.

Currently in lldd_abort_task, if we fail to internally abort IO, then
the slot of SMP IO is not released, but sas_task will still be later
released, so the slot's sas_task is NULL, which will cause NULL pointer
when hisi_sas_slot_task_free happens later.

To resolve, check the return value of internal abort, and release the
slot if it failed.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add function for upper-layer to reset controller when all else fails.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For consistency, remove the "hisi_sas_" prefix.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Handle the situation that PHY UP and DOWN irq happen simultaneously.
There is no mechanism of SoC HW to ensure this situation will never
happen. So, we add this handle just in case.
Signed-off-by: NXiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch includes:
(1) Disable transport layer retry
(2) Support CQ time and count interrupt coal
(3) fix link FIFO full issue
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NZhao Nenglong <zhaonenglong@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There are some rules to decide which error code has the high priority
when errors happen together:

(1) Error phase of CQ decides the error happens on RX or TX;

(2) For TX error, when DMA/TRANS TX error happen simultaneously, the
    priority of DMA TX error is higher than TRANS TX error, so for the
    priority of TX error: DW2 (DMA TX part) > DW0;

(3) For RX error, when TRANS/DMA/SIPC RX error happen simultaneously,
    the priority of TRANS RX error is higher than DMA and SIPC RX error,
    and we should also keep the rules (the priority of DW3 > DW2), so
    for the priority of RX error: DW1 > DW3 > DW2(SIPC RX part);

(4) There are also a priority we should keep in the same error type.

So, modify slot error code to handle this.

In addition to this, some some error codes are modified according to
recommendation from SoC designer.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When a TMF or internal abort times-out, do not free slot. We expect this
to be done upon later escalated error handling.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Some more locking needs to be added/modified for when
read-modify-writing sas_task.task_state_flags.

Note: since we can attempt to grab this lock in interrupt
      context we should use irq variant of spin_lock.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

After hardreset, we clear up IOs of remote disks, so we need to free
those slots in LLDD.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Check in slot_complete_v2_hw() for whether a task has already been
completed by upper layer.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When issuing an LU reset for a SATA target, issue an internal abort and
a hard reset.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently an internal abort is executed regardless of the result of the
TMF. We should also check the result of the internal abort to see if we
should free the slot.

So change the status code STAT_IO_COMPLETE to TMF_RESP_FUNC_SUCC,
meaning the slot has been successfully aborted.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For error codes which need abort-and-retry, simulate IO timeout and let
SCSI+ATA layers process those errors.

Previously for SSP, we should try to abort the IO in the LLDD and then
pass back to upper layer, but sometimes this would also error. So
Instead of adding special error handling for this scenario in the LLDD,
allow the upper layer to handle completely.

No performance hit is seen by taking this approach.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

We currently do a hard reset for a link reset. Change this to do a link
reset only.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiang Chen <chenxiang@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When sas_port is NULL, then return SAS_PHY_DOWN.

In addition, when the sas_dev is gone then explicitly return
SAS_PHY_DOWN.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently when a root PHY is deformed from a asd_sas_port we try to
release the slots in the LLDD, and fail.

Regardless, it is not right to release this early.

This patch removes the deformed function. As it was before, port
deformation is still done in hisi_sas_phy_down().

It would be nice to actually remove the hisi_sas_port_{de}formed() pair,
however we cannot as we need to know the asd_sas_port index libsas has
associated with an asd_sas_phy.

The hw does actually generate a port id for a PHY, but this seems to a
random number, so ignored for this purpose.

This patch also changes the code to link slots to the hisi_sas_device,
and not hisi_sas_port.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add softreset to clear IO after internal abort device for SATA disk.

The SATA error handling for the controller is based on device internal
abort and softreset function.

The controller does not support internal abort for single IO, so we need
to execute internal abort for device.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Relocate the PHY init code from LLDD hw init path to
hisi_sas_scan_start().
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There are some scenarios that we need to warm-reset to reset registers
of SAS controller. During reset we disable interrupts/DQs/PHYs, and
after reset we re-init the hardware and rescan the topology to see if
anything changed.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NXiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Introduce function to get hisi_sas_port from asd_sas_port.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There is an issue that hisi_sas_dev.running_req is not
decremented properly for internal abort and TMF.

To resolve, only decrease running_req in hisi_sas_slot_task_free()
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There is a potential probe issue in how we trigger the hw initialisation.
Although we use 1s timer to delay hw initialisation, there is still a
potential that sas_register_ha() is not be finished before we start
the PHY init from hw->hw_init().
To avoid this issue, initialise the hw after sas_register_ha() in the
same probe context.
Note: it is not necessary to use 1s timer now (modified v2 hw only).
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Downgrade the exit print in hisi_sas_internal_task_abort()
to dbg level, as info is not required.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NXiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>