- 14 4月, 2017 1 次提交
-
-
由 Ganesh Goudar 提交于
Save the filter tid while creating the server filter, which is used later to retrieve the corresponding filter instance while handling the filter reply. Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 4月, 2017 4 次提交
-
-
由 Russell King 提交于
Allow up to three clocks to be specified and enabled for the orion-mdio interface, which are required for this interface to be accessible on Armada 8k platforms. Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Russell King 提交于
Disable the MDIO interrupt, falling back to polled mode, if the resource size does not allow us to access the interrupt registers. All current DT bindings use a size of 0x84, which allows access, but verifying it is good practice. Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Russell King 提交于
The pre-existing write to disable interrupts on the remove path happens whether we have an interrupt or not. While this may seem to be a good idea, this driver is re-used in many different implementations, some where the binding only specifies four bytes of register space. This access causes us to access registers outside of the binding. Make it conditional on the interrupt being present, which is the same condition used when enabling the interrupt in the first place. Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Russell King 提交于
When the mvmdio driver has an interrupt, it enables the "done" interrupt after requesting its interrupt handler. However, probe failure results in the interrupt being left enabled. Disable it on the failure path. Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 12 4月, 2017 17 次提交
-
-
由 Benjamin Herrenschmidt 提交于
I haven't seen any improvement above that size on the machines I've tested with. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
We set an arbitrary max at 1024 since we pre-allocate the actual descriptor arrays and skb arrays to the full size to keep the code a bit simpler and avoid allocation failures in the reset task. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
Clear stale interrupts on entry, configure FIFO sizes, set FIFO thresholds, configure interrupt mitigation. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
The helpers just take space but don't provide much value. Simple one line comments are more explanatory. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
To remove more confusion. This function is about obtaining the initial MAC address at driver probe time. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
To avoid confusion with the ndo callback and generally be clearer about the purpose of that function Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
So features can be turned on/off via ethtool Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
We found out that HW checksum generation only works from AST2500 onward. This disables it on AST2400 and removes the "no-hw-checksum" properties in the device-trees. The problem we had wasn't related to NC-SI. Also rework the logic testing for that property so it can be used to disable HW checksum generation and checking regardless of whether NC-SI is used or not in case other variants out there need this. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
We test for aspeed chips to handle a couple of special cases, but we do that by checking the machine type which isn't right. Instead check the actual device compatible property. This also updates the dtsi files for the aspeed SoC to match. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
The documentation describes NETIF_F_IP_CSUM as deprecated so let's switch to NETIF_F_HW_CSUM and use the helper to handle unhandled protocols. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joao Pinto 提交于
In the submission of the lastest multiple buffer patch set, this fix was lost. I am sending this patch to put it right again. The fix was originally proposed by Arnd Bergmann. Signed-off-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NJoao Pinto <jpinto@synopsys.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Fugang Duan 提交于
The errata ERR007885 HW fix don't add to i.MX6ul ENET IP version, so add sw workaroud for the chip. Signed-off-by: NFugang Duan <fugang.duan@nxp.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Fugang Duan 提交于
Correct the errata number ERR006358 comment typo. Signed-off-by: NFugang Duan <fugang.duan@nxp.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Fugang Duan 提交于
Many boards use i2c/spi expander gpio as phy-reset-gpios and these gpios maybe registered after fec port, driver should check the return value of .of_get_named_gpio(). Signed-off-by: NFugang Duan <B38611@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Fugang Duan 提交于
In aarch64 system, it requires to trasfer ->dev to dma_alloc_coherent() API, otherwise allocate failed and print kernel warning. Signed-off-by: NFugang Duan <B38611@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Fugang Duan 提交于
In aarch64 system, the BD pointer is 64bit, and the high-order 32-bits of the address is effective, so replace usigned with (void *) type to aovid 64bit address is casted to 32bit in .fec_enet_get_nextdesc() and .fec_enet_get_prevdesc() functions. Signed-off-by: NFugang Duan <fugang.duan@nxp.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Fugang Duan 提交于
Add return value check after calling .of_property_read_u32() to avoid the warning reported by coverity. Signed-off-by: NFugang Duan <fugang.duan@nxp.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 11 4月, 2017 16 次提交
-
-
由 Christoph Hellwig 提交于
Trivial conversion as only one vector is supported, but at least we lose the useless msix_entry member in the per-device structure. Signed-off-by: NChristoph Hellwig <hch@lst.de> Acked-by: NJiri Pirko <jiri@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Tested-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Thanneeru Srinivasulu 提交于
Remove deprecated pci_enable_msix API in favour of its successor pci_alloc_irq_vectors. Signed-off-by: NThanneeru Srinivasulu <tsrinivasulu@cavium.com> Signed-off-by: NSunil Goutham <sgoutham@cavium.com> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Christoph Hellwig 提交于
Remove the deprecated pci_enable_msix API in favour of its successor. Signed-off-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Christoph Hellwig 提交于
Remove the deprecated pci_enable_msix API in favour of its successor, and make sure to handle errors during IRQ setup properly. Signed-off-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
Directly access the fields when needed. The accessors add clutter not clarity and in some cases cause unnecessary read-modify-write type access on the slow (uncached) descriptor memory. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
Add NETIF_F_SG and create multiple TX ring entries for skb fragments. On reclaim, the skb is only freed on the segment marked as "last". Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
Those are non-cachable stores, let's avoid those we don't need. Remove the helper, it's not particularly helpful and since it uses "priv" I can't move it to the header file. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
This moves the packet freeing to a separate function which is also used by ftgmac100_free_buffers() and will be used more in the error path of fragmented sends. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
We'll use variants of this accessor without barriers when building series of descriptors for fragmented sends Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
We have a private lock which isn't terribly useful, and we maintain a "tx_pending" counter for information that's already available via a trivial arithmetic operation. Then we unconditionaly wake the queue even when not stopped. Finally our code in tx isn't really safe vs. a concurrent reclaim. The aspeed chips aren't SMP today but I prefer the code being right and future proof. So rip that out and replace it with more "standard" queue handling, currently with a threshold of 1 queue element, which will be increased when we implement fragmented sends. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
Rather than in the descriptor. The descriptor is mapped non-cachable and rather slow to access. Since to do that we need to keep track of the tx "pointer" we also have no use of all the accesors to manipulate it, just open code it, it's as clear and will help when adding fragmented sends. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
Rather than just transmitting garbage past the end of the small packet. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
Use a simple goto to a drop path at the tail of the function, it will be used in a few more cases soon Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
This will make subsequent rework of the tx path simpler Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
Move it below ftgmac100_xmit() and the rest of the tx path No code change. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin Herrenschmidt 提交于
We have a reset task to reset our chip, use it. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 4月, 2017 2 次提交
-
-
由 Felix Manlunas 提交于
For security reasons, NIC firmware does not allow VF to set its VLAN if PF set it already. Firmware allows VF to set its VLAN if PF did not set it. After the VF instructs the firmware to set the VLAN, VF always indicates (via return 0) that the operation is successful--even for the times when it isn't. Put in a mechanism for the VF's set VLAN function to receive the firmware response code, then make that function return -EPERM if the firmware forbids the operation. Make that mechanism available for other functions that may, in the future, be interested in receiving the response code from the firmware. That mechanism involves adding new fields to struct octnic_ctrl_pkt, so make all users of struct octnic_ctrl_pkt initialize the struct to zero before using it; otherwise, the mechanism might act on uninitialized garbage. Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com> Signed-off-by: NDerek Chickles <derek.chickles@cavium.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Colin Ian King 提交于
On the case where nn->eth_port is null the warning message is printing the port by dereferencing this null pointer. Remove the deference to avoid a crash when printing the warning message. Detected by CoverityScan, CID#1426198 ("Dereference after null check") Fixes: ce22f5a2 ("nfp: separate high level and low level NSP headers") Signed-off-by: NColin Ian King <colin.king@canonical.com> Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-