This makes OHCI use the driver model wakeup control bits for its root hub
(e.g. disable on amd756, because of chip erratum) and for the controller
itself.  It no longer uses the hcd glue bits with those roles, and depends
on the previous patch making the root hub available earlier.

Note that on most platforms (boot code properly setting the RWC bit) this
gives a partial workaround for the way PCI isn't currently flagging devices
that support PME# signals.  (Because of odd PCI init sequencing on PPC.)
That's because many OHCI controllers support "legacy PCI PM" ... without
involving any PCI PM capability.

USB wakeup from STR, if it works on your system, may still involve
tweaking things by hand in /proc/acpi/wakeup.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make the HCD initialization sequence more sane ... notably, setting up
root hubs before HCDs are asked to do their one-time init.  Among other
things, that lets the HCDs do custom root hub init along with all the
other one-time initialization done in the (now misnamed) reset() method.

This also copies the controller wakeup flags into the root hub; it's
done a bit later than would be ideal, but that'll be necessary until
the PCI code initializes them correctly.  (The PCI patch breaks on PPC
due to how it sequences PCI initialization.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds declarations for three USB peripheral controllers:

  - Two high speed USB cores that can be licensed from Mentor Graphics
    to be integrated into silicon:

      * "musbhsfc" is for peripherals only, as found in for example the
        IBM/AMCC 44EP processors.

      * "musbhdrc" is OTG-capable (dual role), and is found in various
        products including OMAP 2430 and the new DaVinci SOCs.

    The "musbh" standing for "Mentor USB Highspeed", the rest standing
    for "Function Controller" or "Dual Role Controller" (OTG-capable).

  - The full speed controller on the FreeScale MPC8272.

Adding these definitions just allows gadget driver code to handle any
controller-specific logic; controller drivers are quite separate.
Signed-off-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Resove a minor FIXME:  don't change MTU while RNDIS link is active,
the other end won't expect such things...
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds support for the USB peripheral controller on AT91
(rm9200, eventually also sam9261 or uClinux) platforms.

More SOC support for Linux-USB ... an uncomplicated pure PIO driver.
It'd be worth using this as a model, if you're starting a driver
for some other peripheral controller.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds support for OHCI on AT91rm9200 based boards.

Possibly of interest here is the way this uses <linux/clk.h> to
gate clocks on/off during system pm state transitions.  That's
typical for non-PCI systems.  Some can go further; Mini-A host
side connectors enable ID-pin sensing.

From: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch modifies the behavior of the EHCI driver in an unlink path
that seems to be causing various issues on some systems.  Those problems
have included issues with disconnection, driver unbinding, and similar
cases where urb unlinking would just not work right.

This patch should help avoid those problems by not turning off the async
(control/bulk) schedule until it's not expecting an "async advance" IRQ,
which comes from the processing passing the schedule head.  Whether the
driver attempts to do such things is dependent on system timings, so
many folk would never have seen these problems.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

ALCHEMY:  Add OHCI support for AU1200

Updated by moving the OHCI support out of the EHCI patch.
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

ALCHEMY:  Add EHCI support for AU1200

Updated by removing the OHCI support
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On the MPC834x processors the multiport host (MPH) EHCI controller has an
erratum in which the port number in the queue head expects to be 0..N-1
instead of 1..N.  If we are on one of these chips we subtract one from
the port number before putting it into the queue head.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adding a Host Mode USB driver for the Freescale 83xx.

This driver supports both the Dual-Role (DR) controller and the
Multi-Port-Host (MPH) controller present in the Freescale MPC8349. It has
been tested with the MPC8349CDS reference system. This driver depends on
platform support code for setting up the pins on the device package in a
manner appropriate for the board in use. Note that this patch requires
selecting the EHCI controller option under the USB Host menu.
Signed-off-by: NRandy Vinson <rvinson@mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch replaces the split ISO raw_mask calculation code in the
iso_stream_init() function that computed incorrect numbers of high
speed transactions for both input and output transfers.

In the output case, it added a superfluous start-split transaction for
all maxmimum packet sizes that are a multiple of 188.

In the input case, it forgot to add complete-split transactions for all
microframes covered by the full speed transaction, and the additional
complete-split transaction needed for the case when full speed data
starts arriving near the end of a microframe.

These changes don't affect the lack of full speed bandwidth, but at
least it removes the MMF errors that the HC raised with some input
streams.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This teaches the EHCI driver about a quirk seen in older NForce2 chips,
adding a workaround to ignore selective suspend requests.  Bus-wide
(so-called "global") suspend still works, as does USB wakeup of a
root hub that's globally suspended.

There's still a hole in this support though.  Strictly speaking, this
should _fail_ selective suspend requests, rather than ignoring them,
since doing it this way means that devices which should be able to issue
remote wakeup are not going to be able to do that.  For now, we'll just
live with that problem ... since usbcore expects to do selective suspend
on the way towards a full bus suspend, and usbcore needs to be able to
do full bus suspend.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

the patch below converts a bunch of semaphores-used-as-mutex in the USB
code to mutexes
Signed-off-by: NArjan van de Ven <arjan@infradead.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch removes unnecessary LINUX_VERSION_CODE macro usage from
drivers/usb/.
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

After the removal of usb-midi.c, there's no longer any external user of
usb_get_string().
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch removes the obsolete USB_MIDI and USB_AUDIO drivers.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Switch from kmalloc+memset to kzalloc.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this does two things:
- use kzalloc where appropriate
- correct error return codes in ioctl
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

another one for kzalloc.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

another for kzalloc.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

another for kzalloc.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

another one for kzalloc
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

another for kzalloc.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

another one for kzalloc.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

another for kzalloc.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

another one for kzalloc.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

kzalloc in dabusb.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this uses kzalloc in hid.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

another one for kzalloc. This covers the storage subdirectory.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

one more conversion to kzalloc.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/usb/core/devio.c: In function `usbdev_read':
drivers/usb/core/devio.c:140: error: invalid type argument of `->'
drivers/usb/core/devio.c:141: error: invalid type argument of `->'
drivers/usb/core/devio.c:142: error: invalid type argument of `->'
drivers/usb/core/devio.c:143: error: invalid type argument of `->'

Cc: Oliver Neukum <oliver@neukum.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this is a small optimisation. It is ridiculous to do a kmalloc for
18 bytes. This puts it onto the stack.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds a Video4Linux2 driver for ZC0301
Image Processor and Control Chip.
Signed-off-by: NLuca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Should allow cheetah_plus cpu types and don't taint
the kernel.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Caught by CONFIG_DEBUG_SPINLOCK.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sun does't put an SEEPROM behind the tigon3 chip, among other things,
so accesses to these areas just give bus timeouts.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because we play this trick where we use ttyS? in increasing minor
numbers for different sunfoo.c drivers, we have to inform the TTY
layer of this.

Do so by setting the tty->name_base appropriately.

Probably there should be a generic way to do this in the serial core,
but for now...
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Caller takes the lock already.

Also, fixup the poll loop in sunhv_break_ctl().  Just
like in console write, we udelay(2) and use a loop
limit of 1000000 iterations.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So that it will show up as /dev/ttyS0.  Otherwise things like
installers will try to run on whatever serial port gets probed
first.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>