* Add ->host_flags to ide_hwif_t to store ide_pci_device_t.host_flags,
  assign it in setup-pci.c:ide_pci_setup_ports().

* Add IDE_HFLAG_PIO_NO_{BLACKLIST,DOWNGRADE} to ide_pci_device_t.host_flags
  and teach ide_get_best_pio_mode() about them.  Also remove needless
  !drive->id check while at it (drive->id is always present).

* Convert amd74xx, via82cxxx and ide-timing.h to use ide_get_best_pio_mode()
  and then remove no longer needed ide_find_best_pio_mode().

There should be no functionality changes caused by this patch.
Acked-by: NShtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
  and convert all users accordingly.

* Remove no longer needed ide_pio_data_t.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Check IORDY bit for PIO modes > 2.

* Some devices claim maximum PIO mode > 2 in id->tPIO, they were punished too
  severly for this by being limited to PIO_SLOW.  Limit them to PIO2 instead.

v2:
* Fix PIO number being returned incorrectly instead of PIO mode
  (Noticed by Sergei).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide_pio_cycle_time() helper.

* Use it in ali14xx/ht6560b/qd65xx/cmd64{0,x}/sl82c105 and pmac host drivers
  (previously cycle time given by the device was only used for "pio" == 255).

* Remove no longer needed ide_pio_data_t.cycle_time field.

v2:
* Fix "ata_" prefix (Noticed by Jeff).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Nowadays core IDE code handles restoring of PIO and DMA modes
  (ide-io.c:ide_start_power_step() etc) so remove open-coded version
  from sc1200_resume().

  There should be no change in behavior because settings done by
  sc1200_resume() were always overridden by generic_ide_resume()
  and ide_{start,stop}_power_step().

* Bump driver version.

Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Do the same thing as probe_hwif() and always disable DMA so chipset DMA
  enabled bit gets cleared (if the drive doesn't support DMA ide_set_dma()
  won't try to tune it anyway).

* Add TODO comment about respecting ->using_dma setting.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The driver used to depend on BIOS settings for deciding whether it is OK
to use DMA.  However it seems that BIOS doesn't always handle all cases
correctly so just let IDE core to decide about this.  It should be a safe
thing to do now, after the driver went through heavy bugfixing.

Thanks for bugreport and testing the patch goes out to Sven Niedner.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Always set ->autotune so PIO gets correctly auto-tuned (previously
  ->autotune was only set when ->dma_base wasn't available, however
  ->ide_dma_check()/->speedproc() was always trying to tune PIO when
  tuning DMA).

* Move code responsible for programming chipset for PIO mode from
  svwks_tune_chipset() to svwks_tune_pio().  Don't tune PIO when tuning
  DMA (this is no longer needed since ->autotune is always set now).

* Handle PIO modes early in svwks_tune_chipset() so DMA configuration
  registers don't get cleared when programming PIO mode.

* Bump driver version.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename ide_pci_device_t.flags to ide_pci_device_t.host_flags
  and IDEPCI_FLAG_ISA_PORTS flag to IDE_HFLAG_ISA_PORTS.

* Add IDE_HFLAG_SINGLE flag for single channel devices.

* Convert core code and all IDE PCI drivers to use IDE_HFLAG_SINGLE
  and remove no longer needed ide_pci_device_t.channels field.

v2:
* Fix issues noticed by Sergei:
  - correct code alignment in scc_pata.c
  - s/IDE_HFLAG_SINGLE/~IDE_HFLAG_SINGLE/ in serverworks.c
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide_dev_has_iordy() helper and use it sl82c105 host driver.

* Remove no longer needed ide_pio_data_t.use_iordy field.

v2/v3:
* Fix issues noticed by Sergei:
  - correct patch description
  - fix comment in ide_get_best_pio_mode()

v4:
* Fix "ata_" prefix (Noticed by Jeff).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Print info about overriding PIO mode in ide_get_best_pio_mode().

* Remove info about overriding PIO mode from cmd64{0,x} host drivers.

* Remove no longer needed ide_pio_data_t.overridden field.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add sil_tuneproc() wrapper for siimage_tuneproc() which also sets
  PIO mode on the device.

* Add missing ide_get_best_pio_mode() call to sil_tuneproc() so
  "pio" == 255 (autotune) is handled correctly (previously PIO0 was used)
  and "pio" values > 4 && < 255 are filtered to PIO4 (instead of PIO0).

* Add code limiting maximum PIO mode according to the pair device capabilities
  to sil_tuneproc().

* Convert users of config_siimage_chipset_for_pio() to use sil_tune_pio() and
  sil_tuneproc().  This fixes PIO fallback in siimage_config_drive_for_dma() to
  use max PIO mode available instead of PIO4 (config_siimage_chipset_for_pio()
  used wrong arguments for ide_get_best_pio_mode() and as a results always
  tried to set PIO4).

* Remove no longer needed siimage_taskfile_timing()
  and config_siimage_chipset_for_pio().

* Enable ->autotune unconditionally and remove PIO tuning for UDMA/MDMA modes
  from siimage_speedproc()

* Bump driver version.

v2:
* Fix issues noticed by Sergei:
  - correct pair device check
  - trim only taskfile PIO to the slowest of the master/slave
  - enable ->autotune unconditionally and remove PIO tuning for UDMA/MDMA modes
    from siimage_speedproc()
  - add TODO item for IORDY bugs
  - minor cleanups
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Split off exisiting atiixp_tuneproc() into atiixp_tune_pio()
  and then add setting device PIO mode to atiixp_tuneproc().

* Add missing ide_get_best_pio_mode() call to atiixp_tuneproc() so
  "pio" == 255 (autotune) is handled correctly and "pio" values > 4 && < 255
  are filtered to PIO4 (previously "pio" == 5 could result in wrong timings
  being used and "pio" values > 4 && < 255 in an OOPS).

* Handle PIO modes early in atiixp_speedproc() so save_mdma_mode[]
  doesn't get cleared.

* In atiixp_dma_check():
  - fix max_mode argument for ide_get_best_pio_mode()
  - don't call atiixp_dma_2_pio() so PIO1 doesn't get remapped to PIO0
  - use atiixp_tuneproc() instead of atiixp_speedproc()

* Bump driver version.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Various old IDE drivers go mapping ROM devices for no apparent reason and
without using the ROM mapping API we now have. They don't actually use
the ROM they map and the new libata drivers are happy without it being
mapped so rather than port them lets just junk it for the next -rc1.
Signed-off-by: NAlan Cox <alan@redhat.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The two CONFIG variables

        CONFIG_ETRAX_IDE_CSE1_16_RESET
        CONFIG_ETRAX_IDE_CSP0_8_RESET

appear to have been dead since way back in 2.5.xx days:

http://www.linuxhq.com/kernel/v2.5/75/arch/cris/drivers/KconfigSigned-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Cc: Michael Starvik <starvik@axis.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

One card submitted by user.
Signed-off-by: NMarcin Juszkiewicz <openembedded@hrw.one.pl>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Workaround for errata A308: turn down the UDMA mode and retry
the DMA command when the data lost condition is detected.

take2:
udma_filter() hook is used to limit ATAPI UDMA mode.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NAkira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move to using inline function variant of eieio instead of inline assmebly.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Cc: kou.ishizaki@toshiba.co.jp
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Currently, CONFIG_X86_CMPXCHG64 both enables boot-time checking of
the cmpxchg64b feature and enables compilation of the set_64bit() family.
Since the option is dependent on PAE, and since KVM depends on set_64bit(),
this effectively disables KVM on i386 nopae.

Simplify by removing the config option altogether: the boot check is made
dependent on CONFIG_X86_PAE directly, and the set_64bit() family is exposed
without constraints.  It is up to users to check for the feature flag (KVM
does not as virtualiation extensions imply its existence).
Signed-off-by: NAvi Kivity <avi@qumranet.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If root raised the default wakeup threshold over the size of the
output pool, the pool transfer function could overflow the stack with
RNG bytes, causing a DoS or potential privilege escalation.

(Bug reported by the PaX Team <pageexec@freemail.hu>)

Cc: Theodore Tso <tytso@mit.edu>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are no users of i2c-isa left, so we can finally get rid of it.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

With this patch the abituguru refuses to load on non Abit motherboards, as
discussed in lkml CONFIG_BREAK_MY_MACHINE thread.
Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch changes the driver to also detect uguru3's which hold 0x08 at DATA
initially, as has been reported here:
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=220160

Also when an uguru3's holds 0x0014 in the ID register it will now report
"Abit AB9 Pro" as motherboard identification.
Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This fixes bug #8593:
http://bugzilla.kernel.org/show_bug.cgi?id=8593Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

We don't need to initialize fan_min in this driver, as the fan_div
attributes are read-only.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Add support for the w83627ehf thermal sensor types. I made them read-only,
as the BIOS is supposed to set them up properly. This information makes it
easier to find out which temperature channel corresponds to the CPU.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

If VBAT monitoring is disabled, enable it. Original patch from
an anonymous contributor on the lm-sensors trac system:
http://lm-sensors.org/ticket/2218Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

The W83627EHF and similar chips have 6 VID input pins, add support
for them. The driver changes the input voltage level automatically
if the current setting is not correct for the detected CPU model.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

* I have experimental evidence that the W83627EHG needs more than 1
second to refresh all the measured values. Increase the caching time to
1.5 second.
* When changing a fan clock divider, the corresponding fan speed
measurement register is no longer valid, until the next time the chip
will refresh it. One way to fix this is to pretend that the cache is
still valid for one more period (1.5 second.)
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

If the Super-I/O device is disabled, it is likely the BIOS has a good
reason for leaving it disabled, so give a warning when enabling it --
it's not likely to be wired correctly or be able to give good data.

Also, if the Super-I/O device is configured with an address of 0, the
driver refuses to initialize it.
Signed-off-by: NDavid Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Remove i2c-isa from the w83627ehf driver, and use a platform driver
instead.
Signed-off-by: NDavid Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Add description for the W83627DHG chip to Kconfig.
Signed-off-by: NDavid Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

coretemp_device_remove() can become static.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch adds support for the LM93 hardware monitoring chip.
Signed-off-by: NHans J. Koch <hjk@linutronix.de>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Also protects ourselves against a possible division by zero.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch adds a new driver for the hardware monitoring features of the
third revision of the Abit uGuru chip, found on recent Abit
motherboards. This is an entirely different beast then the first and
second revision (its again a winbond microcontroller, but the "protocol"
to talk to it and the bank addresses are very different.
Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Add support for the "temperature mode" fan speed control. In this mode,
the user can define 3 temperature/speed trip points, and the chip will
set the speed automatically according to the temperature changes.
Signed-off-by: NPhil Endecott <kernel@chezphil.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

The w83627ehf driver changes the fan clock divider automatically when
a new min fan speed is set. It is supposed to preserve the fan speed
reading while doing so, bug doesn't really. Fix it.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch fixes the detection of volt inputs with a reading of more then 240
units.
Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch adds the SMSC SCH5317 chip (device ID 0x85) as a supported
device to the smsc47b397 driver.

Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>