Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 25 2月, 2011 1 次提交
  3. 18 2月, 2011 2 次提交
  5. 28 1月, 2011 1 次提交
  7. 07 1月, 2011 1 次提交
    • N
      omap2+: wdt: trivial sparse fixes · a9b365bd
      由 Nishanth Menon 提交于 
      omap2_wd_timer_disable is declared in wdtimer.h and used by hwmod
function pointers for usage, the header inclusion is necessary
to ensure that the prototype and function remains consistent.
omap_wdt_latency is passed as a pointer and does not need global scope

Fixes sparse warnings:
arch/arm/mach-omap2/devices.c:981:31: warning: symbol 'omap_wdt_latency' was not declared. Should it be static?
arch/arm/mach-omap2/wd_timer.c:27:5: warning: symbol 'omap2_wd_timer_disable' was not declared. Should it be static?
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      a9b365bd
  9. 22 12月, 2010 2 次提交
    • P
      OMAP2+: wd_timer: disable on boot via hwmod postsetup mechanism · ff2516fb
      由 Paul Walmsley 提交于 
      The OMAP watchdog timer IP blocks require a specific set of register
writes to occur before they will be disabled[1], even if the device
clocks appear to be disabled in the CM_*CLKEN registers.  In the MPU
watchdog case, failure to execute this reset sequence will eventually
cause the watchdog to reset the OMAP unexpectedly.

Previously, the code to disable this watchdog was manually called from
mach-omap2/devices.c during device initialization.  This causes the
watchdog to be unconditionally disabled for a portion of kernel
initialization.  This should be controllable by the board-*.c files,
since some system integrators will want full watchdog coverage of
kernel initialization.  Also, the watchdog disable code was not
connected to the hwmod shutdown code.  This means that calling
omap_hwmod_shutdown() will not, in fact, disable the watchdog, and the
goal of omap_hwmod_shutdown() is to be able to shutdown any on-chip
OMAP device.

To resolve the latter problem, populate the pre_shutdown pointer in
the watchdog timer hwmod classes with a function that executes the
watchdog shutdown sequence.  This allows the hwmod code to fully
disable the watchdog.

Then, to allow some board files to support watchdog coverage
throughout kernel initialization, add common code to mach-omap2/io.c
to cause the MPU watchdog to be disabled on boot unless a board file
specifically requests it to remain enabled.  Board files can do this
by changing the watchdog timer hwmod's postsetup state between the
omap2_init_common_infrastructure() and omap2_init_common_devices()
function calls.

1. OMAP34xx Multimedia Device Silicon Revision 3.1.x Rev. ZH
   [SWPU222H], Section 16.4.3.6, "Start/Stop Sequence for WDTs (Using
   WDTi.WSPR Register)"
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Charulatha Varadarajan <charu@ti.com>
      ff2516fb
    • P
      OMAP2+: wd_timer: separate watchdog disable code from the rest of mach-omap2/devices.c · 81fbc5ef
      由 Paul Walmsley 提交于 
      Split the wd_timer disable code out into its own file,
mach-omap2/wd_timer.c; it belongs in its own file rather than
cluttering up devices.c.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Charulatha Varadarajan <charu@ti.com>
      81fbc5ef
  11. 21 12月, 2010 1 次提交
  13. 09 10月, 2010 2 次提交
    • P
      OMAP: control: move plat-omap/control.h to mach-omap2/control.h · 4814ced5
      由 Paul Walmsley 提交于 
      Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap.  This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.

In response, move the SCM headers into mach-omap2/.

As part of this, remove the direct SCM access from the OMAP UDC
driver.  It was clearly broken.  The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
      4814ced5
    • C
      OMAP2PLUS: WDT: Fix: Disable WDT after reset during init · 20252d46
      由 Charulatha V 提交于 
      Inorder to avoid any assumptions from bootloader, the watchdog
timer module is reset during init. This enables the watchdog
timer.

Therefore, it is required to disable WDT after it is reset
during init. Otherwise the system would reboot as per the default
watchdog timer registers settings.

Later, when the watchdog driver is loaded, the watchdog timer settings
is adjusted as per the default timer_margin set in the driver and the
driver would supports the normal operations supported by OMAP watchdog
timer.
Signed-off-by: NCharulatha V <charu@ti.com>
Reported-by: NKevin Hilman <khilman@deeprootsystems.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      20252d46
  15. 05 10月, 2010 1 次提交
  17. 02 10月, 2010 1 次提交
    • K
      omap4 hsmmc: Register offset handling · 91a0b089
      由 kishore kadiyala 提交于 
      In OMAP4, as per new PM programming model, the legacy registers
which were there in OMAP3 are all shifted by 0x100 while new one's
are added from offset 0 to 0x10.
For OMAP4, the register offset appending of 0x100 done in devices.c
currently, is moved to driver file.This change fits in for current
implementation as well as once the driver undergoes hwmod adaptation.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      91a0b089
  19. 30 9月, 2010 1 次提交
  21. 28 9月, 2010 2 次提交
  23. 03 9月, 2010 1 次提交
  25. 12 8月, 2010 1 次提交
    • L
      ASoC: multi-component - ASoC Multi-Component Support · f0fba2ad
      由 Liam Girdwood 提交于 
      This patch extends the ASoC API to allow sound cards to have more than one
CODEC and more than one platform DMA controller. This is achieved by dividing
some current ASoC structures that contain both driver data and device data into
structures that only either contain device data or driver data. i.e.

 struct snd_soc_codec    --->  struct snd_soc_codec (device data)
                          +->  struct snd_soc_codec_driver (driver data)

 struct snd_soc_platform --->  struct snd_soc_platform (device data)
                          +->  struct snd_soc_platform_driver (driver data)

 struct snd_soc_dai      --->  struct snd_soc_dai (device data)
                          +->  struct snd_soc_dai_driver (driver data)

 struct snd_soc_device   --->  deleted

This now allows ASoC to be more tightly aligned with the Linux driver model and
also means that every ASoC codec, platform and (platform) DAI is a kernel
device. ASoC component private data is now stored as device private data.

The ASoC sound card struct snd_soc_card has also been updated to store lists
of it's components rather than a pointer to a codec and platform. The PCM
runtime struct soc_pcm_runtime now has pointers to all its components.

This patch adds DAPM support for ASoC multi-component and removes struct
snd_soc_socdev from DAPM core. All DAPM calls are now made on a card, codec
or runtime PCM level basis rather than using snd_soc_socdev.

Other notable multi-component changes:-

 * Stream operations now de-reference less structures.
 * close_delayed work() now runs on a DAI basis rather than looping all DAIs
   in a card.
 * PM suspend()/resume() operations can now handle N CODECs and Platforms
   per sound card.
 * Added soc_bind_dai_link() to bind the component devices to the sound card.
 * Added soc_dai_link_probe() and soc_dai_link_remove() to probe and remove
   DAI link components.
 * sysfs entries can now be registered per component per card.
 * snd_soc_new_pcms() functionailty rolled into dai_link_probe().
 * snd_soc_register_codec() now does all the codec list and mutex init.

This patch changes the probe() and remove() of the CODEC drivers as follows:-

 o Make CODEC driver a platform driver
 o Moved all struct snd_soc_codec list, mutex, etc initialiasation to core.
 o Removed all static codec pointers (drivers now support > 1 codec dev)
 o snd_soc_register_pcms() now done by core.
 o snd_soc_register_dai() folded into snd_soc_register_codec().

CS4270 portions:
Acked-by: NTimur Tabi <timur@freescale.com>

Some TLV320aic23 and Cirrus platform fixes.
Signed-off-by: NRyan Mallon <ryan@bluewatersys.com>

TI CODEC and OMAP fixes
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>

Samsung platform and misc fixes :-
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NJassi Brar <jassi.brar@samsung.com>
Signed-off-by: NSeungwhan Youn <sw.youn@samsung.com>

MPC8610 and PPC fixes.
Signed-off-by: NTimur Tabi <timur@freescale.com>

i.MX fixes and some core fixes.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

J4740 platform fixes:-
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>

CC: Tony Lindgren <tony@atomide.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: Kuninori Morimoto <morimoto.kuninori@renesas.com>
CC: Daniel Gloeckner <dg@emlix.com>
CC: Manuel Lauss <mano@roarinelk.homelinux.net>
CC: Mike Frysinger <vapier.adi@gmail.com>
CC: Arnaud Patard <apatard@mandriva.com>
CC: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
      f0fba2ad
  27. 04 8月, 2010 2 次提交
  29. 05 7月, 2010 2 次提交
  31. 21 5月, 2010 1 次提交
  33. 14 5月, 2010 1 次提交
  35. 11 5月, 2010 1 次提交
  37. 03 5月, 2010 1 次提交
  39. 30 4月, 2010 1 次提交
  41. 24 4月, 2010 1 次提交
  43. 24 2月, 2010 1 次提交
  45. 16 2月, 2010 2 次提交
  47. 12 12月, 2009 1 次提交
  49. 23 11月, 2009 3 次提交
  51. 21 10月, 2009 1 次提交
    • T
      omap: headers: Move remaining headers from include/mach to include/plat · ce491cf8
      由 Tony Lindgren 提交于 
      Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.

This was done with:

#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"

for header in $headers; do
	old="#include <mach\/$header"
	new="#include <plat\/$header"
	for dir in $omap_dirs; do
		find $dir -type f -name \*.[chS] | \
			xargs sed -i "s/$old/$new/"
	done
	find drivers/ -type f -name \*omap*.[chS] | \
		xargs sed -i "s/$old/$new/"
	for file in $other_files; do
		sed -i "s/$old/$new/" $file
	done
done

for header in $(ls $mach_dir_old/*.h); do
	git mv $header $plat_dir_new/
done
Signed-off-by: NTony Lindgren <tony@atomide.com>
      ce491cf8
  53. 25 9月, 2009 1 次提交
  55. 23 9月, 2009 2 次提交
  57. 29 8月, 2009 1 次提交
  59. 13 5月, 2009 1 次提交