Silence the following warning:
"warn: returning -1 instead of -ENOMEM is sloppy".
Signed-off-by: NSantosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch to use ndo_get_stats64 to get 64bit statistics.
Two sync entries are used (one for Rx and one for Tx).
Signed-off-by: NJunchang Wang <junchangwang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a bug that causes a kernel panic when the number of received doorbells
is larger than number of entries in the inbound doorbell queue (current
default value = 512).

Another possible indication for this bug is large number of spurious
doorbells reported by tsi721 driver after reaching the queue size maximum.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Chul Kim <chul.kim@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: <stable@vger.kernel.org>		[3.2.x+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix setting bio flags in drivers (sd_dif/floppy).
Signed-off-by: NMuthukumar R <muthur@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If probing the RTC didn't succeed due to failed RTC register access, the
RTC device will be unregistered.  Then, when removing the module
r9701_remove() causes a kernel crash while trying to unregister a not
registered RTC device.  Fix this by doing RTC register access test before
RTC device registration.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

class_create() doesn't return a NULL, it only returns ERR_PTRs.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

class_create() never returns NULLs only ERR_PTRs.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Nothing fancy:
- sent bytes count is notified in the start_xmit path right before
  updating the owner bit in the hardware Tx descriptor (E. Dumazet)
- avoid useless tp->dev dereferencing in start_xmit (E. Dumazet)

Use of netdev_reset_queue is favored over proper accounting in
rtl8169_tx_clear_range since the latter would need more work for the
same result (nb: said accounting degenerates to nothing in xmit_frags).
Signed-off-by: NIgor Maravic <igorm@etf.rs>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>

Switch to use ndo_get_stats64 to get 64bit statistics.
Two sync entries are used (one for Rx and one for Tx).
Signed-off-by: NJunchang Wang <junchangwang@gmail.com>
Reviewed-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

commit 56a2559b (md/raid10: recognise replacements ...)
changed 'run' to set ->replacement or ->rdev depending on the
'Replacement' status if the device, but it didn't remove the
old unconditional setting of 'rdev'.  So it was largely ineffective.

So remove that now.
Signed-off-by: NNeilBrown <neilb@suse.de>

Production GMA3600/3650 hardware turns out to be subtly different to the
development platforms.  This combined with a minor driver bug is causing
the kernel to hang on these platforms.

This patch does the following

 - turn down a couple of messages that were meant to be debug and are
   causing much confusion

 - ensure the hotplug interrupt is disabled on Cedartrail systems.

 - fix a bug where gtt roll mode called psbfb_sync, which tries to sync
   the 2D engine. On other devices it is harmless as the 2D engine is
   present but not in use when in gtt roll mode, on Cedartrail it causes
   a hang

Without these changes 3.3-rc hangs on boot on Cedartrail based systems.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In 'ql_adapter_initialize'
the first call for 'spin_unlock_irqrestore()' is with hw_flags = 0,
which is as good as 'spin_unlock_irq()' (unconditional interrupt
enabling). If this is intended, then for better performance
'spin_unlock_irqrestore()' can be replaced with 'spin_unlock_irq()'
and 'spin_lock_irqsave()' can be replaced by 'spin_lock_irq()
Signed-off-by: NSantosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix new sparse errors introduced in commit 62212171 (mlx4_en: dont
change mac_header on xmit)
Reported-by: NOr Gerlitz <or.gerlitz@gmail.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow array field values out of range as per HID 1.11 specification,
section 6.2.25:

	Rather than returning a single bit for each button in the group, an
	array returns an index in each field that corresponds to the pressed
	button (like keyboard scan codes). An out-of range value in and array
	field is considered no controls asserted.

Apparently, "and" above is a typo and should be "an".

This fixes at least Waltop tablet pen clicks - otherwise BTN_TOUCH is never
released.

The relevant part of Waltop tablet report descriptors is this:

	0x09, 0x42,         /*          Usage (Tip Switch),         */
	0x09, 0x44,         /*          Usage (Barrel Switch),      */
	0x09, 0x46,         /*          Usage (Tablet Pick),        */
	0x15, 0x01,         /*          Logical Minimum (1),        */
	0x25, 0x03,         /*          Logical Maximum (3),        */
	0x75, 0x04,         /*          Report Size (4),            */
	0x95, 0x01,         /*          Report Count (1),           */
	0x80,               /*          Input,                      */

This is a regression fix for commit b4b583d4 ("HID: be more strict when
ignoring out-of-range fields").
Signed-off-by: NNikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fix log messages and corrects some typos

Change logging of failure to enable MSI/MSI-X to display device's PCI
address instead of eth%d. Rectify a typo.
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Reviewed-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch recodes the MRRS cap for 5719 A0 devices as a PCI quirk.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Factor out the the existing allocation and free operations
so that they can be used individually.

This is to improve code readability, and also to prepare for
possible future changes like better error recovery and more
dynamic configuration (e.g on-the-fly resizing of the rings).

This change represents a straight up relocation of the existing
code into separate routines without changing any of the contained
code itself.  Local variables are relocated as necessary.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since all that include/linux/if_ppp.h does is #include <linux/ppp-ioctl.h>,
this replaces the occurrences of #include <linux/if_ppp.h> with
#include <linux/ppp-ioctl.h>.

It also corrects an error in Documentation/networking/l2tp.txt, where
it referenced include/linux/if_ppp.h as the source of some definitions
that are actually now defined in include/linux/if_pppol2tp.h.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This moves the definitions of the ioctls, constants and structures
relating to the ppp_generic interface to userspace out from if_ppp.h
to a new file, ppp-ioctl.h.  The new file has my copyright since I
designed and implemented the ppp_generic interface in the late 1990s.
None of the contents of this file comes from the original if_ppp.h
published by Carnegie Mellon University.

Of the remainder of if_ppp.h, only the PPP_MTU definition was being
used, and this replaces the uses of it with PPP_MRU (which is identical).
Therefore, this replaces the entire file with the single line

#include <linux/ppp-ioctl.h>

which clearly doesn't contain any CMU code.  Thus I have removed the
CMU copyright notice with its problematic advertising clause, and in
fact since it's only one trivial line I have not added any other
copyright notice.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This changes the copyright notices on the PPP code that I developed
in the late 1990s from being copyright The Australian National
University to copyright Paul Mackerras.  I can do this as I have an
acknowledgement in writing from the Head of the Computer Science
Department at ANU (where I worked then) that ANU does not claim any
intellectual property in this code.

While I'm at it, change the copyright notice from BSD-style to
GNU GPL like the rest of the kernel.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GRC reset causes the read DMA engine to go into a mode that breaks up
requests into 256 bytes.  A PHY reset is required to bring it back to
the normal mode.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

for weak memory model architectures to ensure that the chip will DMA
valid BD data.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Loopback on 9K packet fails because the chip has a DMA limit of 4K.  The
loopback test logic uses a single BD for simplicity.  Fix it by reducing
the jumbo packet size to the DMA limit.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even if cards supports 1.8V I/O voltage those should anyway be
initialized at 3.3V I/O according to (e)MMC, SD and SDIO specs.
Some eMMC and embedded SDIO devices are able to be initialized
at 1.8V as well, but it is better to be safe.

Do note that initialization in this context means that the card
has been completely powered off, otherwise the card will remain
at the last I/O voltage level that were negotitiated.

Due to the above being taken care of the suspend/resume issues
for UHS-I SD-cards has been fixed.
Signed-off-by: NUlf Hansson <ulf.hansson@stericsson.com>
Acked-by: NPhilip Rakity <prakity@marvell.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

On a system with large pages (64k in my case), the following BUG is
triggered in MMC core:

[    2.338023] BUG: failure at drivers/mmc/core/core.c:221/mmc_start_request()!
[    2.338102] Kernel panic - not syncing: BUG!
[    2.338155] Call trace:
[    2.338228] [<ffffffc00008635c>] dump_backtrace+0x0/0x120
[    2.338317] [<ffffffc0003365ec>] dump_stack+0x14/0x1c
[    2.338403] [<ffffffc000336990>] panic+0xbc/0x1f0
[    2.338498] [<ffffffc00027a494>] mmc_start_request+0x154/0x184
[    2.338600] [<ffffffc00027abdc>] mmc_start_req+0x110/0x140
[    2.338701] [<ffffffc00028604c>] mmc_blk_issue_rw_rq+0x7c/0x39c
[    2.338804] [<ffffffc00028652c>] mmc_blk_issue_rq+0x1c0/0x468
[    2.338905] [<ffffffc000287564>] mmc_queue_thread+0x68/0x118
[    2.338995] [<ffffffc0000bc308>] kthread+0x84/0x8c

This is because of a 64k request with a max_req_size of 64k-1 bytes.

The following patch fixes the problem by limiting the max_blk_count
such that max_blk_count * max_blk_size == max_req_size. I couldn't
pursuade the compiler to emit a shift instead of a div without encoding
the shift explicitly.
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

On i.MX53 we have to write a special SDHCI_CMD_ABORTCMD to the
SDHCI_TRANSFER_MODE register during a MMC_STOP_TRANSMISSION
command. This works for SD cards. However, with MMC cards
the MMC_SET_BLOCK_COUNT command is used instead, but this
needs the same handling. Fix MMC cards by testing for the
MMC_SET_BLOCK_COUNT command aswell. Tested on a custom i.MX53
board with a Transcend MMC+ card and eMMC.

The kernel started used MMC_SET_BLOCK_COUNT in 3.0, so this
is a regression for these boards introduced in 3.0; it should
go to 3.0/3.1/3.2-stable.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

A recent commit "mmc: core: Use delayed work in clock gating framework"
(597dd9d7) introduced a default 200ms delay before clock gating
actually takes place.  This means that every time an MMC interface
becomes idle it first stays on for 200ms before gating its clock. This
leads to increased power consumption and is therefore a clear regression.
This patch restores the original behaviour by setting the default delay
to 0. Users prioritising throughput over power efficiency can still
modify the delay via sysfs.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds the specific part which handles the PCAN-USB Pro adapter
from PEAK-System Technik (http://www.peak-system.com). The PCAN-USB Pro
adapter is a dual-channel USB 2.0 adapter compliant with CAN specifications
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NStephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds the specific part which handles the PCAN-USB adapter from
PEAK-System Technik (http://www.peak-system.com). The PCAN-USB adapter is
a sja1000 based, mono-channel USB 1.1 adapter compliant with CAN
specifications 2.0A (11-bit ID) and 2.0B (29-bit ID).
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NStephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds the core of the peak_usb driver which handles PEAK-System
Technik PCAN USB adapters. It defines the parts which are common to the
PCAN-USB adapters: can network interfaces management, network-to/from-usb
data path interface, timestamps management...
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NStephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds support to the PCAN-PC Card PCMCIA card from
PEAK-System Technik (www.peak-system.com). This card is a CAN interface
for the PC Card slot. It is available as a single or dual-channel version.
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NStephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds the support of some new PEAK-System PCI cards in the CAN
network sub-system. These are:

PCAN-PCIeC (PCI-ExpressCard)
PCAN-mminiPCI (mini-PCI)
PCAN-PCI (PCI next-gen)

This patch also adds the control of the blinking leds of the PCAN-PCIeC.
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NStephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

drivers/net/can/cc770/cc770.c included 'linux/can/dev.h' twice,
remove the duplicate.
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

{g|s}etnumtcs() today returns a u8 that is only used by the DCB code
to verify no error occurred. Today the driver implementations return
negative error codes which end up being non-zero so the logic works
out but triggers some sparse warnings.

To fix the sparse warnings convert the return value to an int.

CC: Eilon Greenstein <eilong@broadcom.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

dcb netlink code calls setup_tc to init hardware traffic classes
to use for DCB. At some call sites the return values are not
checked for errors and in one case may return -EINVAL back to
the net/dcbnl.c caller which is expecting a u8.

This fixes some smatch hits and although failures are never
seen in practive its best to check return codes.
Reported-by: NDan Carenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The old code would += the total errors every time
stats were gathered.  Instead, keep a count of short-pkt
and long-pkt counters and then simply add them together
for the rx-over-length stat.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Noticed with the 8168d (-vb-gr, aka RTL_GIGA_MAC_VER_26).

ConfigX registers should only be written while the Config9346 lock
is held.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Reported-by: NNick Bowler <nbowler@elliptictech.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 529febee.

To quote Dirk:
	This commit introduces a check for the USB PHY clock.
	Problem is that CTRL_PHY_CLK_VALID bit seems not to be present
	on all Freescale ehci implementations, at least P1022 does not
	have it.  So this check always fails and the driver never gets
	loaded.

So we need to revert this patch.
Reported-by: NDirk Eibach <Eibach@gdsys.de>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As part of the big network driver reorg, each vendor directory defaults to
yes, so that older config's can migrate correctly. Looks like this one
got missed.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>