SPLICE_F_NONBLOCK is clearly documented to only affect blocking on the
pipe.  In __generic_file_splice_read(), however, it causes an EAGAIN
if the page is currently being read.

This makes it impossible to write an application that only wants
failure if the pipe is full.  For example if the same process is
handling both ends of a pipe and isn't otherwise able to determine
whether a splice to the pipe will fill it or not.

We could make the read non-blocking on O_NONBLOCK or some other splice
flag, but for now this is the simplest fix.
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
CC: stable@kernel.org
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

If there's no feature-barrier key in xenstore, then it means its a fairly
old backend which does uncached in-order writes, which means ORDERED_DRAIN
is appropriate.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

When barriers are supported, then use QUEUE_ORDERED_TAG to tell the block
subsystem that it doesn't need to do anything else with the barriers.
Previously we used ORDERED_DRAIN which caused the block subsystem to
drain all pending IO before submitting the barrier, which would be
very expensive.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

scsi-ml uses REQ_TYPE_BLOCK_PC for flush requests from file
systems. The definition of REQ_TYPE_BLOCK_PC is that we don't retry
requests even when we can (e.g. UNIT ATTENTION) and we send the
response to the callers (then the callers can decide what they want).
We need a workaround such as the commit
77a42297 to retry BLOCK_PC flush
requests. We will need the similar workaround for discard requests too
since SCSI-ml handle them as BLOCK_PC internally.

This uses REQ_TYPE_FS for flush requests from file systems instead of
REQ_TYPE_BLOCK_PC.

scsi-ml retries only REQ_TYPE_FS requests that have data to
transfer when we can retry them (e.g. UNIT_ATTENTION). However, we
also need to retry REQ_TYPE_FS requests without data because the
callers don't.

This also changes scsi_check_sense() to retry all the REQ_TYPE_FS
requests when appropriate. Thanks to scsi_noretry_cmd(),
REQ_TYPE_BLOCK_PC requests don't be retried as before.

Note that basically, this reverts the commit
77a42297 since now we use REQ_TYPE_FS
for flush requests.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

q->bar_rq.rq_disk is NULL. Use the rq_disk of the original request
instead.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

the block layer doesn't set rq->cmd_type on flush requests. By
definition, it should be REQ_TYPE_FS (the lower layers build a command
and interpret the result of it, that is, the block layer doesn't know
the details).
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

The struct cont_t is just a set of virtual function pointers.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Use memdup_user when user data is immediately copied into the
allocated region.  Some checkpatch cleanups in nearby code.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: Chirag Kantharia <chirag.kantharia@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Jens, any reason why this isn't included in your for-2.6.36 yet?

=
From: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Subject: [PATCH resend] scsi: convert discard to REQ_TYPE_FS from REQ_TYPE_BLOCK_PC

The block layer (file systems) sends discard requests as REQ_TYPE_FS
(the role of REQ_TYPE_FS is that setting up commands and interpreting
the results). But SCSI-ml treats discard requests as
REQ_TYPE_BLOCK_PC.

scsi-ml can handle discard requests as REQ_TYPE_FS
easily. scsi_setup_discard_cmnd() sets up struct request and the bio
nicely. Only remaining issue is that discard requests can't be
completed partially so we need to modify sd_done.

This conversion also fixes the problem that discard requests aren't
retried when possible (e.g. UNIT ATTENTION).
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: cleanup interrupt_not_for_us
In the case of MSI/MSIX interrutps, we don't need to check
if the interrupt is for us, and in the case of the intx interrupt
handler, when checking if the interrupt is for us, we don't need
to check if we're using MSI/MSIX, we know we're not.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: change printks to dev_warn, etc.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: separate cmd_alloc() and cmd_special_alloc()
cmd_alloc() took a parameter which caused it to either allocate
from a pre-allocated pool, or allocate using pci_alloc_consistent.
This parameter is always known at compile time, so this would
be better handled by breaking the function into two functions
and differentiating the cases by function names.  Same goes
for cmd_free().
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: use consistent variable names
"h", for the hba structure and "c" for the command structures.
and get rid of trivial CCISS_LOCK macro.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: forbid hard reset of 640x boards
The 6402/6404 are two PCI devices -- two Smart Array controllers
-- that fit into one slot.  It is possible to reset them independently,
however, they share a battery backed cache module.  One of the pair
controls the cache and the 2nd one access the cache through the first
one.  If you reset the one controlling the cache, the other one will
not be a happy camper.  So we just forbid resetting this conjoined
mess.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: sanitize max commands
Some controllers might try to tell us they support 0 commands
in performant mode.  This is a lie told by buggy firmware.
We have to be wary of this lest we try to allocate a negative
number of command blocks, which will be treated as unsigned,
and get an out of memory condition.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: Fix hard reset code.
Smart Array controllers newer than the P600 do not honor the
PCI power state method of resetting the controllers.  Instead,
in these cases we can get them to reset via the "doorbell" register.

This escaped notice until we began using "performant" mode because
the fact that the controllers did not reset did not normally
impede subsequent operation, and so things generally appeared to
"work".  Once the performant mode code was added, if the controller
does not reset, it remains in performant mode.  The code immediately
after the reset presumes the controller is in "simple" mode
(which previously, it had remained in simple mode the whole time).
If the controller remains in performant mode any code which presumes
it is in simple mode will not work.  So the reset needs to be fixed.

Unfortunately there are some controllers which cannot be reset by
either method. (eg. p800).  We detect these cases by noticing that
the controller seems to remain in performant mode even after a
reset has been attempted.  In those cases we ignore the controller,
as any commands outstanding on it will result in stale completions.
To sum up, we try to do a better job of resetting the controller if
"reset_devices" is set, and if it doesn't work, we ignore that
controller.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: factor out cciss_reset_devices()
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Rationale for this is that I will also need to use this code
in fixing kdump host reset code prior to having the hba structure.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: factor out cciss_enter_performant_mode
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: factor out cciss_wait_for_mode_change_ack()
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: make cciss_put_controller_into_performant_mode as __devinit
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: cleanup some debug ifdefs
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: factor out cciss_p600_dma_prefetch_quirk()
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: factor out cciss_enable_scsi_prefetch()
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: factor out CISS_signature_present()
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: factor out cciss_find_board_params
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: fix leak of ioremapped memory
in cciss_pci_init error path.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: factor out cciss_find_cfgtables
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: factor out cciss_wait_for_board_ready()
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: factor out cciss_find_memory_BAR()
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: remove board_id parameter from cciss_interrupt_mode()
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: factor out cciss_board_disabled
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: factor out cciss_lookup_board_id
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: save pdev pointer in per hba structure early to avoid passing it around so much.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cciss: Set the performant mode bit in the scsi half of the driver
In a couple of places, the performant mode bit wasn't being set in
the scsi half of the driver, causing commands to seem to hang.  Use
enqueue_cmd_and_start_io() where appropriate.  This fixes a bug that

	echo engage scsi > /proc/driver/cciss/cciss0

would hang.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Signed-off-by: NDaniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

This is just bd_openers, protected by the bd_mutex.
Signed-off-by: NDaniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

This is just bd_openers, protected by the bd_mutex.
Signed-off-by: NDaniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Same approach as blkfront_closing:
 * Grab the bdev safely, holding the info mutex.
 * Zap xbdev safely, holding the info mutex.
 * Try bdev removal safely, holding bd_mutex.
Signed-off-by: NDaniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

We cannot read backend state within bdev operations, because it risks
grabbing the state change before xenbus gets to do it.

Fixed by tracking deferral with a frontend switch to Closing. State
exposure isn't strictly necessary, but the backends won't mind.

For a 'clean' deferral this seems actually a more decent protocol than
raising errors.
Signed-off-by: NDaniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>