The LP (and probably N) PHY has the same radio disabled bit as
the higher-revision A and G PHYs.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SDIO works (more or less), so remove the BROKEN dependency and
let people test it.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the following build error when CONFIG_B43_LEDS is not selected:

drivers/net/wireless/b43/main.c: In function 'b43_remove':
drivers/net/wireless/b43/main.c:4990: error: 'struct b43_leds' has no member named 'stop'
drivers/net/wireless/b43/main.c:4991: error: 'struct b43_leds' has no member named 'work'
make[4]: *** [drivers/net/wireless/b43/main.o] Error 1
Signed-off-by: NAlbert Herranz <albert_herranz@yahoo.es>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't abuse wl->current_dev in the LED work for checking whether we're
going down. Add an explicit variable.
This fixes a crash on rmmod dereferencing the wl->current_dev NULL pointer
in various other places of the driver.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current verison of b43 uses "b43_phyop_switch_analog_generic" for A,
G and LP phys.

According to the spec, this is the wrong behaviour for the LP PHY
(see: http://bcm-v4.sipsolutions.net/802.11/PHY/Anacore )

While no problems on the x86 plattform where seen, this leads to a crash
on the BCM5354 SoC (MIPS 32 LE plattform).
This patch implements the analog switch for LP PHYs according to the
specs. It fixes the crash
signed-off-by: NThomas Ilnseher <illth@gmx.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reduces IRQ pressure by about one third on a saturated link
by disabling the PMQ mechanism. We currently don't use that mechanism.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds support for verbose runtime statistics.
It defaults to off and must be enabled in debugfs, if desired.
The first measurement may be incorrect, because statistics are not cleared
after they got enabled through debugfs.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

synchronize_irq is meaningless for SDIO. sdio_release_irq will
sync the IRQ thread for us.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need to release the SDIO host before locking the driver mutex.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We don't need to call the irqsafe callbacks.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds support for Soft-MAC SDIO devices to b43.
The driver still lacks some fixes for SDIO devices, so it's currently
marked as BROKEN.
Signed-off-by: NAlbert Herranz <albert_herranz@yahoo.es>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes most of the b43 suspend/resume code (it's handled by mac80211)
and moves the registration of devices to the attachment phase. This is
required, because we must not register/unregister devices on suspend/resume.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds a new usbid for Zcomax XG-705A to the device table.

Cc: stable@kernel.org
Reported-by: NJari Jaakola <jari.jaakola@gmail.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a bug in 4965 powersave that appears to
be related to the way it keeps track of its data
during sleep, but we haven't found it yet. Due to
that, using powersave may spontaneously cause the
device to SYSASSERT when transitioning from sleep
to wake. Therefore, disable powersave for 4965,
until (if ever, unfortunately) we can identify
and fix the problem.

Cf. http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1982
which was closed, but now has re-appeared with
IDLE mode, which probably means we never really
fixed it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can not assume antenna "A" is the first valid anttena for
all the NIC. Need to make sure choice the correct antenna based on
h/w configuration for transmit to avoid sending frame on invalid
antenna
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RX handling maintains a few lists that keep track of the RX buffers.
Buffers move from one list to the other as they are used, replenished, and
again made available for usage. In one such instance, when a buffer is used
it enters the "rx_used" list. When buffers are replenished an skb is
attached to the buffer and it is moved to the "rx_free" list. The problem
here is that the buffer is first removed from the "rx_used" list _before_ the
skb is allocated. Thus, if the skb allocation fails this buffer remains
removed from the "rx_used" list and is thus lost for future usage.

Fix this by first allocating the skb before trying to attach it to a list.
We add an additional check to not do this unnecessarily.
Reported-by: NRick Farrington <rickdic@hotmail.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we cleaned up the driver to properly tell mac80211 about HT rates
("iwlwifi: use iwl_hwrate_get_mac80211_idx where appropriate"), we broke
internal rate indexing in 2.4 GHz band.
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Tested-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes a resume failure where a signal is pending on resume
so the firmware upload fails.
This removes the interruptible sleep, because we don't really need it.
In the worst case (with broken firmware) the sleep loop will take 1 second.
In the common case (working firmware), it will only take a few milliseconds.
So we don't really need to be interruptible.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When this was added no defaults were set and it seems
this implies n. Default this to y.
Reported-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When processing MIB interrupts, OFDM and CCK error
handling routines for low RSSI values have to be invoked
only when the channel mode is 11G/11B. Since HT channels
will also fall under the bands 2Ghz/5Ghz, check appropriately.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Force wake the mac80211 queues on init.
Under rare circumstances they may be stopped, if a DMA error or
something else causes a device reset while a queue was stopped.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As the hostap driver was converted to use net_device_ops, a mistake was
made in hostap_main.c (commit 5ae4efbc).
Originally, the tx_queue_len was set to 0 for every other interface than
HOSTAP_INTERFACE_MASTER, but the new fragment of code sets tx_queue_len to
0 only for HOSTAP_INTERFACE_MASTER. The opposite of the previous
behavior makes the driver to drop all packets in AP mode.

Change the way 0 is assigned to tx_queue_len according to the original
logic.
Signed-off-by: NMartin Decky <martin@decky.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

o Add QLogic copyright, add linux-driver@qlogic.com to
  MAINTAINERS.
o Delete old contact information.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Redesign tx timeout handling in line with new firmware
reset design that co-ordinates with other PCI function
drivers.

o For NX3031, first try to reset PCI function's own
  context before requesting firmware reset.

o For NX2031, since firmware heartbit is not supported
  directly request firmware reset.
Signed-off-by: NAmit Kumar Salecha <amit@netxen.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Release file firmware when no firmware reset is required.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Access on card memory through memory controller (agent)
  rather than moving small pci window around. Clean up the
  code for moving windows around.

o Restrict memory accesss to 64 bit, currently only firmware
  download uses this.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use 8 byte strides for firmware download into card
memory since oncard memory controller needs 8 byte
(64 bit) accesses. This avoids unnecessary rmw cycles.
Signed-off-by: NAmit Kumar Salecha <amit@netxen.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit f6eb9b1f, "tg3: Add 5717 asic
rev" changed how the rx return ring size operations are done.  It
effectively inverts the sense of the previous test, but it failed to
also invert the resulting sizes.  This patch corrects that error.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When CONFIG_INET is disabled, netxen has a build failure:

netxen_nic_main.c:(.text+0x118fd1): undefined reference to `netxen_config_indev_addr'

so make that function just an empty stub when CONFIG_INET=n.
(not "inline" since that conflicts with other declarations of it)
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.

To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.

  # cat /sys/class/net/wlan0/uevent
  DEVTYPE=wlan
  INTERFACE=wlan0
  IFINDEX=5

This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.

The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The txq_set_wrr() function in drivers/net/mv643xx_eth.c is
unused, not even referenced under #if 0 or something like that,
which results in a compile-time warning:

drivers/net/mv643xx_eth.c:1070: warning: 'txq_set_wrr' defined but not used

Fix: remove it.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MPC8360 QE UCC ethernet controllers hang when changing link duplex
under a load (a bit of NFS activity is enough).

  PHY: mdio@e0102120:00 - Link is Up - 1000/Full
  sh-3.00# ethtool -s eth0 speed 100 duplex half autoneg off
  PHY: mdio@e0102120:00 - Link is Down
  PHY: mdio@e0102120:00 - Link is Up - 100/Half
  NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out
  ------------[ cut here ]------------
  Badness at c01fcbd0 [verbose debug info unavailable]
  NIP: c01fcbd0 LR: c01fcbd0 CTR: c0194e44
  ...

The cure is to disable the controller before changing speed/duplex
and enable it afterwards.

Though, disabling the controller might take quite a while, so we
better not grab any spinlocks in adjust_link(). Instead, we quiesce
the driver's activity, and only then disable the controller.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We'll need ugeth_disable() and ugeth_enable() calls earlier in the
file, so rearrange some code to avoid forward declarations.

The patch doesn't contain any functional changes.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to specs, when auto-negotiation is disabled, Marvell PHYs need
a software reset after changing speed/duplex forcing bits. Otherwise,
the modified bits have no effect.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Error handling code following a kzalloc should free the allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@

x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...x...+> }
(
x->f1 = E
|
 (x->f1 == NULL || ...)
|
 f(...,x->f1,...)
)
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Error handling code following a kmalloc should free the allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@

x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...x...+> }
(
x->f1 = E
|
 (x->f1 == NULL || ...)
|
 f(...,x->f1,...)
)
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And also do a better job of returning proper NET_{RX,XMIT}_ values.

Based on a patch and suggestions by Mark Smith.

This fixes CVE-2009-2903
Reported-by: NMark Smith <lk-netdev@lk-netdev.nosense.org>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macro res_size in drivers/net/dm9000.c is a copy of resource_size in
linux/ioport.h. Remove the function and use resource_size instead.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>