Better style and better supports idle_bias_off which we're going to
implement.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Ensure we're in a known state when we restart.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Raise the ramp time to 50ms to cover corner cases, use the startup bias
generator, explicitly reset the ramp circuit when complete and reorder
things all of which should improve performance somewhat for systems that
are sensitive to noise from VMID.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reduces the amount of time taken to stabilise them.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The enable of the single ended line outputs on wm_hubs devices performs
better if the output is enabled prior to starting VMID. Since inactive
outputs are held at VMID anyway there is little cost to doing this for
unused outputs. Add callbacks into wm_hubs and keep track of which outputs
are really active so we can disable them once we're active.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

According to the mixer path diagram input sources' attenuators logically
belong to the playback path and DMIC boost only affects capture.
Signed-off-by: NPaul Fertser <fercerpav@gmail.com>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This brings the TLVs in sync with the documentation and allows to properly
manipulate mic boost controls with alsamixer.
Signed-off-by: NPaul Fertser <fercerpav@gmail.com>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch should fix output through speakers using HP mixer.
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix I2S digital interface power for recording.
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add DMIC switches and controls to ALC5632 codec.
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Refactored DAPM routes to add voice support.

- Added undocumented register
- Used AIF in/out
- Added missed voice items and routes
- Added DMIC input
- Romoved unrelevant items
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There is no Phone Mix<->Mono Mix route in datasheet.
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Rename capture switches to common scheme XXX2REC.
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add voice DAC playback switch.
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Remove extra zero from volume step in DECLARE_TLV_DB_SCALE macro.
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Correct spelling "memroy" to "memory" in
sound/soc/codecs/twl4030.c
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The device is generally not succeptible to the issues that cause this to
be an issue.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It's set unconditionally.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The VMID ramp rate is supposed to be 0x3, not 11b. Fix that.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Make sure we generate enough BCLKs for I2S style modes by always having
a minimum of two channels worth of clocks for the BCLK.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

No practical impact but now we have the control type we may as well use
it for the slightly nicer sequencing.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Now that we're not implementing GPIO or microphone detection support
there's no users for the read() function any more.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJarkko Nikula <jarkko.nikula@bitmer.com>

Make the mechanism used for WM8994 more like that for WM1811 and WM8958:
provide the logic to distinguish between headphone and headset and hard
code the reporting of sensible SND_JACK values. Should integration with
other detection mechanisms be required we can add appropriate callbacks
(though some integrations should be able to use the subsystem ones).
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Otherwise we might get an error if the GPIO is configured as an input
since that makes the register volatile and a suspended device can't be
read from.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is the default state that the runtime PM infrastructure expects so
instead just kick the runtime PM core to suspend us if we're not doing
anything (as is default).
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix build breakage by using the correct API call to add kcontrols.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Looks like nobody is or will be using this code.
Signed-off-by: NFelipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In cases where we should enter STANDBY DAPM will power us up, otherwise
there is no need to power up and we can remain in OFF.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We can enable VMID independently of the bias in some use cases so we need
to ensure that the core device is powered up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Currently ASoC can only add kcontrols using codec and platform component device
handles. It's also desirable to add kcontrols for DAIs (i.e. McBSP) and for
SoC card machine drivers too. This allows the kcontrol to have a direct handle to
the parent ASoC component DAI/SoC Card/Platform/Codec device and hence easily
get it's private data.

This change makes snd_soc_add_controls() static and wraps it in the folowing
calls (card and dai are new) :-

snd_soc_add_card_controls()
snd_soc_add_codec_controls()
snd_soc_add_dai_controls()
snd_soc_add_platform_controls()

This patch also does a lot of small mechanical changes in individual codec drivers
to replace snd_soc_add_controls() with snd_soc_add_codec_controls().

It also updates the McBSP DAI driver to use snd_soc_add_dai_controls().

Finally, it updates the existing machine drivers that register controls to either :-

1) Use snd_soc_add_card_controls() where no direct codec control is required.
2) Use snd_soc_add_codec_controls() where there is direct codec control.

In the case of 1) above we also update the machine drivers to get the correct
component data pointers from the kcontrol (rather than getting the machine pointer
via the codec pointer).
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The second line output mixer has the controls for the line input bypasses
in the opposite order.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>