There is a very small possibility (previously unimagined
by us) that the whole Mass Storage delayed status happens
rather early, before we even get our XferNotReady event.

In that case, we will be queueing a request to ep0 while
we're still on Setup Phase and we would be waiting for
another usb_ep_queue() forever.

Handle such cases by clearing dwc->delayed_status so that
we start control status from the next XferNotReady like
there was no wait for Delayed Status.

Tested against Linux 3.2-rc3 and USB30CV tool from USB-IF
(on a Windows XP with USB3 PCIe card).
Signed-off-by: NFelipe Balbi <balbi@ti.com>

ep->max_streams is a mere hint to the gadget
driver that 'ep' supports stream handling. Using
that as a decision variable for enabling streams
was my worst brain-fart to date.

Instead, we should check from the Superspeed
Endpoint Companion Descriptor if the endpoint
has requested streams. For that we need a little
re-factoring but it is now correct.
Debugged-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

previous commit fixed part of it but it was still
calling usb_ep_queue() from IRQ context without
loosing locks. That cannot be done otherwise we will
have a recursive locking.

Also, we need to assign the 'dep' pointer on
dwc->ep0_usb_req otherwise we will have a NULL
pointer dereference on dwc3_map_buffer_to_dma().
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Instead of special functions and shortcuts for sending our internal
answers to the host we started doing what the gadget does and used the
public API for this. Since we only were using a few fields the
usb_request was enough. Later added the list handling in order to
synchronize the host / gadget events and now we require to have the
dwc3_request struct around our usb_request or else we touch memory that
does not belong to us. So this patch does this.
Reported-by: NPartha Basak <p-basak2@ti.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We mask the correct bits within the wrong register. The power
optimization mode is stored hwparam1 register and not in hwparam0.
Reported-by: NPartha Basak <p-basak2@ti.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

the new module_platform_driver macro is a helper
for modules which just register and unregister the
platform_driver. It allows us to delete a few
duplicated lines.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

DWC3 revisions <1.88a have an issue which would
case a missing Disconnect event if cable is
disconnected while there's a Setup packet
pending the FIFO.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

DWC3 revisions <1.90a have an issue which would cause
a missing USB3 Reset event. In such cases, it's
suggested that we follow the steps of a normal
USB3 Reset on Connection Done Event.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

RTL revisions <1.83a have an issue where, depending
on the link partner, the USB link might do multiple
entry/exit of low power states before a transfer
takes place causing degraded throughput.

The suggested workaround is to clear bits
12:9 of DCTL register if we see a transition
from U1|U2 to U0 and only re-enable that on
a transfer complete IRQ and we have no pending
transfers on any of the enabled endpoints.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch avoids the compiler spitting out the following warning:
|drivers/usb/dwc3/gadget.c:1304: warning: 'trb' is used uninitialized \
	in this function

This is only uninitialized if the list of to-cleanup TRBs is empty which
should not be the case because we call this functions once a transfer
completed so it should be on list.

In order to make the warning disappear we return early. This should
never happen and the WARN_ON_ONCE(1) is there in case it happens
so we can investigate what went wrong.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Since the re-worked ep0 handling (which uses HW's hints to recognize the ep0
status) we lost the delayed status handling. This is used by the file and mass
storage gadget to gain some extra time so setup its internal status before it
can proceed further requests.
In particular the storage gadget does nothing on USB_REQ_SET_CONFIGURATION but
wakes up a thread which handles the request. If the udc driver continues ep0
handling before the thread did its work then then endpoint is not yet
configured and further requests will fail. Once the gadget is ready, it will
enqueue an empty packet which is used for synchronization.
In order to fix this issue, the patch does the following:
Set ->delayed_status once the delayed_status has been notices and do not
continue on the next XferNotReady event. We will continues ep0 processing once
the gadget enqueued the zero packet for synchronization.

A cleaner approach would be to enforce the gadget to enqueue an empty
(zero) request even for the status phase but this would do for now.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We wait for the XferNotReady before we start the transfer and by then we
know ep0 state in which we supposed to be.
This is some cleanup work for the following patch in which we require to
know the ep0 state before the transfer completes.
While here, also change the argument to dwc3_ep0_do_control_status() so
we don't require the complete event structure but only the required
piece of information.
Inspired-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

sparse caught three mistakes on this driver,
fix them:

drivers/usb/dwc3/ep0.c:806:29: warning: duplicate const
drivers/usb/dwc3/debugfs.c:481:15: warning: symbol 'dwc3_debugfs_init' \
	was not declared. Should it be static?
drivers/usb/dwc3/debugfs.c:518:16: warning: symbol 'dwc3_debugfs_exit' \
	was not declared. Should it be static?
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There were a few coding style issues with this driver
which are now fixed:

drivers/usb/dwc3/debugfs.c:48: WARNING: Use #include \
	<linux/uaccess.h> instead of <asm/uaccess.h>
drivers/usb/dwc3/debugfs.c:484: ERROR: space required \
	before the open brace '{'
drivers/usb/dwc3/ep0.c:261: WARNING: line over 80 characters
drivers/usb/dwc3/ep0.c:287: WARNING: suspect code indent \
	for conditional statements (16, 23)
drivers/usb/dwc3/gadget.c:749: WARNING: line over 80 characters
drivers/usb/dwc3/gadget.c:1267: WARNING: line over 80 characters
drivers/usb/dwc3/gadget.h:116: WARNING: line over 80 characters
drivers/usb/dwc3/io.h:42: WARNING: Use #include \
	<linux/io.h> instead of <asm/io.h>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

A few inits like the scale value or the removal of the DISSCRAMBLE is
done in the gadget code however it touches a general register.
Move this piece to the core.c file since it is likely to be requied by
both, parts of the core (device and host).
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There are two where need to set operational mode:
- during initialization while we decide to run in host,device or DRD
  mode
- at runtime via the debugfs interface.

This patch provides a new function which sets the operational mode and
moves its initialiation to the mode switch instead in the gadget code
itself.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In "usb: dwc3: remove special status request handling in ep0" I simplied
a few things and used the generic API for the status transfers. The bug
I introcuded here is that we queue now requests to dep[1] but we don't
clear that list in the stall+start case.
Actually we don't need to use dep[1] at all. We only did in the past to
talk to the correct endpoint (i.e. in or out). This is now take care of
in a diffent place within the ep0 code. So we could queue the in
transfers to dep[0] and don't use dep[1] at all.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The first access was correct, the second was wrong.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

hardware will tell us how many event buffers we
need to support, so let's allocate the array
dynamically too.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

if we ever have an omap with multiple instances of
the DWC3 IP, we need unique names for them. In order
to achieve that, let's use the dwc3_get/put_device_id()
calls to give us an unique device identifier.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

if we want to support situations where we have
both SoC and PCIe versions of the IP on the same
platform, we need to have sequential numbers between
them, otherwise we will still have name collisions.

Because of that, we need to move dwc3_get/put_device_id()
to core.c and export that symbol to be used by glue
layers.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The GetStatus (STD)-request is handled the driver and uses a tiny hack
to send the two bytes long answer. This patch removes the custom hack
uses the normal usb_ep_queue() for that.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If we stall and restart we have to reset also this flag to 0 as there is
nothing pending anymore.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

None of these are required atm.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The read and write operation is atomic and we need no locking around
this operations. What we need however is a lock that is held which
ensures that the content of the DWC3_GCTL has not been changed. With
this, the conten may have been change changed after the first but before
our write back.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We can have three modules here: dwc3.ko, dwc3-omap.ko and dwc3-pci.ko.
The later have already ids-aliases for probing and is fine. The omap
module has alias for DT but lacks alias for the "native"
platform_device. Maybe we should get rid of it and stick to the DT name?
Both glue modules create a new device for which the dwc3.ko module is
responsible and that one lacks the platform alias.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Sometimes the host might be trying to initiate Data or
Status phase for an older Control transfer. In such
situations we must STALL that transfer and restart
the state machine rather than letting such situation
go through the wire.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This makes testing a lot easier when trying to
switch between host and device modes.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

I have talked to USB-IF about USB30CV issuing SetAddres()
with a device on Configured state and they have agreed on
changing USB30CV not to do so.

Adding back the STALL reply in such case and while at
that, also add a debugging message for an address which
is too large.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

now that we have host support, we must depend
on both sides.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

host prototypes are there, let's move gadget's
closer.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We can decide in runtime if that will be used
or not.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The Designware USB3 IP can be configured with
an internal xHCI. If we're running on such a
version, let's start the xHCI stack.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There's no need to add driver_data for something
we can fetch from HW.

This also makes our id_table unnecessary - at least
for now -, so we also remove it on the same patch.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This will allow us to only allocate memory when
we actually need.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this is mainly for testing. In order to be able
to test if we're enumerating correctly on all
speeds, let that be controlled by a module
parameter.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

when we remove the gadget driver, it will already
do that for us.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

* git://git.samba.org/sfrench/cifs-2.6:
  cifs: check for NULL last_entry before calling cifs_save_resume_key
  cifs: attempt to freeze while looping on a receive attempt
  cifs: Fix sparse warning when calling cifs_strtoUCS
  CIFS: Add descriptions to the brlock cache functions

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, efi: Calling __pa() with an ioremap()ed address is invalid
  x86, hpet: Immediately disable HPET timer 1 if rtc irq is masked
  x86/intel_mid: Kconfig select fix
  x86/intel_mid: Fix the Kconfig for MID selection