Rate control algorithms may need access to a station's
HT capabilities, so share the ht_info struct in the
public station API.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sta_info->txrate_idx member isn't used by all RC algorithms
in the way it was intended to be used, move it into those that
require it (only PID) and keep track in the core code of which
rate was last used for reporting to userspace and the mesh MLME.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As more preparation for a saner rate control algorithm API,
share the supported rates bitmap in the public API.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This variable in sta_info is only used in a meaningful way
by the Intel RC algorithms, so move it into those.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes mac80211 to not rely on the rate control
algorithm to update sta->tx_retry_failed and sta->tx_retry_count
(even if we don't currently use them), removes a number of
completely unused values we don't even show in debugfs and
changes the code in ieee80211_tx_status() to not look up the
sta_info repeatedly.

The only behaviour change here would be not calling the rate
control function rate_control_tx_status() when no sta_info is
found, but all rate control algorithms ignore such calls anyway.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In analogy with the previous patch to make mac80211-hwsim
verify that the virtual interface pointers are correct,
this makes it very that it knows about all station structs.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch changes mac80211 to share some more data about
stations with drivers. Should help iwlwifi and ath9k when
 they get around to updating, and might also help with
implementing rate control algorithms without internals.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211-hwsim is a debugging tool for mac80211, and as such
it can very well verify that mac80211 isn't passing junk to
drivers, especially the vif pointer is prone to this because
for vlan interfaces the AP interface pointer needs to be passed.
This makes mac80211-hwsim add a magic cookie to the private vif
area and verify it whenever an operation is called that gets a
vif pointer.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These should never happen, but better warn about them than
crashing a driver, the fact that they never happen is rather
subtle throughout mac80211.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the code to handle regular interfaces out of main.c and
into iface.c, keep only the master interface stuff in main.c.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's really no reason for mac80211 to be using its
own interface type defines. Use the nl80211 types and
simplify the configuration code a bit: there's no need
to translate them any more now.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers need to know the basic rateset to be able to configure
the ACK/CTS programming in hardware correctly.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some comments refer to 80211.o or similar; also remove
a comment about implementing fragments better, we really
have better things to do.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Most of the scan functions are called ieee80211_sta_scan_*
or similar, make clean it up so they are all just called
ieee80211_scan_*.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The bridge_packets configuration really should be per virtual
interface (theoretically per AP/VLAN, but this is much easier);
there currently is no way to set it yet though. Also invert
the option to "NO_BRIDGE_PACKETS" so the default is to bridge.

While at it, also document the flags properly.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It really doesn't belong into the wireless extensions code.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This way all the utility functions are at the top, then the
state machine and externally callable functions are moved to
the bottom. Also clean up ieee80211_i.h a bit and add a few
comments about which functions are called from where.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we remove an interface, we can currently end up having
a pointer to it left in local->scan_sdata after it has been
set down, and then with a hardware scan the scan completion
can try to access it which is a bug. Alternatively, a scan
that started as a hardware scan may terminate as though it
was a software scan, if the timing is just right.

On SMP systems, software scan also has a similar problem,
just canceling the delayed work and setting a flag isn't
enough since it may be running concurrently; in this case
we would also never restore state of other interfaces.

This patch hopefully fixes the problems by always invoking
ieee80211_scan_completed or requiring it to be invoked by
the driver, I suspect the drivers that have ->hw_scan() are
buggy. The bug will not manifest itself unless you remove
the interface while hw-scanning which will also turn off
the hw, and then add a new interface which will be unusable
until you scan once.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we stop an interface, the work on it may still be pending
or running. We do cancel the timer, but we do not currently
protect against the work struct. The race is very unlikely to
hit -- it'll happen only when the driver is using mac80211's
workqueue to run long-running tasks and the sta/mesh works are
delayed for quite a bit.

This patch fixes it by cancelling the work explicitly.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch splits off mesh handling from the STA/IBSS.
Unfortunately it increases mesh code size a bit, but I
think it makes things clearer. The patch also reduces
per-interface run-time memory usage.

Also clean up a few places where ifdef is not required.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The timer restart is done wrongly, we shouldn't set the REQ_RUN
bit when the scan has finished if it hadn't been set before the
scan started. If the timer fires during the scan, it will set
REQ_RUN and then we can run the work for it, if it didn't fire
then we shouldn't run its work either.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This I shouldn't have moved to the scan implementation, move
it back to the MLME where it belongs, to the notification.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_sta_expire uses the internal __sta_info_unlink
function which can become static if this function is moved
to sta_info.c.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

And support setting both long and short retries independently.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RF kill support is enabled when CONFIG_RFKILL
is set.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some of the functions in main.c are re-ordered in such
a way that all local functions are defined before mac80211
and pci callbacks.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The generic reset command is unused.  Each interface type needs to
handle the reset command differently since after reset, the firmware is
dead and interface-specific mechanisms must be used to reinitialize the
card.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This cleans up zd1211rw's own regulatory work, and makes use of
the new cfg80211 regulatory_hint().
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds the new wireless regulatory infrastructure. The
main motiviation behind this was to centralize regulatory
code as each driver was implementing their own regulatory solution,
and to replace the initial centralized code we have where:

* only 3 regulatory domains are supported: US, JP and EU
* regulatory domains can only be changed through module parameter
* all rules were built statically in the kernel

We now have support for regulatory domains for many countries
and regulatory domains are now queried through a userspace agent
through udev allowing distributions to update regulatory rules
without updating the kernel.

Each driver can regulatory_hint() a regulatory domain
based on either their EEPROM mapped regulatory domain value to a
respective ISO/IEC 3166-1 country code or pass an internally built
regulatory domain. We also add support to let the user set the
regulatory domain through userspace in case of faulty EEPROMs to
further help compliance.

Support for world roaming will be added soon for cards capable of
this.

For more information see:

http://wireless.kernel.org/en/developers/Regulatory/CRDA

For now we leave an option to enable the old module parameter,
ieee80211_regdom, and to build the 3 old regdomains statically
(US, JP and EU). This option is CONFIG_WIRELESS_OLD_REGULATORY.
These old static definitions and the module parameter is being
scheduled for removal for 2.6.29. Note that if you use this
you won't make use of a world regulatory domain as its pointless.
If you leave this option enabled and if CRDA is present and you
use US or JP we will try to ask CRDA to update us a regulatory
domain for us.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch resolves a few issues found with multiq including wording
suggestions and a problem seen in the allocation of queues.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This new action will have the ability to change the priority and/or
queue_mapping fields on an sk_buff.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is intended to add a qdisc to support the new tx multiqueue
architecture by providing a band for each hardware queue.  By doing
this it is possible to support a different qdisc per physical hardware
queue.

This qdisc uses the skb->queue_mapping to select which band to place
the traffic onto.  It then uses a round robin w/ a check to see if the
subqueue is stopped to determine which band to dequeue the packet from.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

inet6_rsk() is called on a struct request_sock * before we
have checked whether the socket is an ipv6 socket or a ipv6-
mapped ipv4 socket. The access that triggers this is the
inet_rsk(rsk)->inet6_rsk_offset dereference in inet6_rsk().

This is arguably not a critical error as the inet6_rsk_offset
is only used to compute a pointer which is never really used
(in the code path in question) anyway. But it might be a
latent error, so let's fix it.

Spotted by kmemcheck.
Signed-off-by: NVegard Nossum <vegard.nossum@gmail.com>
Acked-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dst garbage collector dst_gc_task() may not be scheduled as we
expect it to be in __dst_free().

Indeed, when the dst_gc_timer was replaced by the delayed_work
dst_gc_work, the mod_timer() call used to schedule the garbage
collector at an earlier date was replaced by a schedule_delayed_work()
(see commit 86bba269).

But, the behaviour of mod_timer() and schedule_delayed_work() is
different in the way they handle the delay. 

mod_timer() stops the timer and re-arm it with the new given delay,
whereas schedule_delayed_work() only check if the work is already
queued in the workqueue (and queue it (with delay) if it is not)
BUT it does NOT take into account the new delay (even if the new delay
is earlier in time).
schedule_delayed_work() returns 0 if it didn't queue the work,
but we don't check the return code in __dst_free().

If I understand the code in __dst_free() correctly, we want dst_gc_task
to be queued after DST_GC_INC jiffies if we pass the test (and not in
some undetermined time in the future), so I think we should add a call
to cancel_delayed_work() before schedule_delayed_work(). Patch below.

Or we should at least test the return code of schedule_delayed_work(),
and reset the values of dst_garbage.timer_inc and dst_garbage.timer_expires
back to their former values if schedule_delayed_work() failed.
Otherwise the subsequent calls to __dst_free will test the wrong values
and assume wrong thing about when the garbage collector is supposed to
be scheduled.

dst_gc_task() also calls schedule_delayed_work() without checking
its return code (or calling cancel_scheduled_work() first), but it
should fine there: dst_gc_task is the routine of the delayed_work, so
no dst_gc_work should be pending in the queue when it's running.
Signed-off-by: NBenjamin Thery <benjamin.thery@bull.net>
Acked-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vlan devices are not reading the gso max size of the parent device.  As
a result devices that do not support 64K max gso size are currently
failing.

This issue is seen on 2.6.26 kernels as well and the same patch should be
able to be applied without any issues.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:

	drivers/net/wireless/ath9k/beacon.c
	drivers/net/wireless/ath9k/core.h

Noticed by Michael Chan.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>