wm5110 rev D is the first chip to use headphone detection IP 2, specify
such and make a small correction as the impedance value is actually read
in 0.5 ohm increments now.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

No point in revisiting ranges the detection will be no more accurate
the second time simply report that the resistance is right on the
range boundry.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

The microphone detection code is run as delayed work to provide
additional debounce, it is possible that the jack could have been
removed by the time we process the microphone detection. Turn this
case into a no op.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

We need to make sure we reset back to our starting state, especially
making sure that we have disabled poll in the register cache.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

Improve readability by creating a define for each microphone detection
level.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

Always cross check with the ID state and the source of interrupt.
Also add a case in which ID Source is ID_GND but LATCH state is set
wrongly. This uses the previous Link stat to determine the new state.
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

The Palmas device contains only a USB VBUS-ID detector, so added a
compatible type *ti,palmas-usb-vid*. Didn't remove the existing compatible
types for backward compatibility.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

Commit 338de0ca (extcon: gpio: Use gpio driver/chip debounce if supported)
introduced a call to gpio_set_debounce() before actually requesting the
respective gpio pin from the gpio subsystem.

The gpio subsystem expects that a gpio pin was requested before modifying its
state. Not doing so results in a warning from gpiolib, and the gpio pin is
auto-requested. This in turn causes the subsequent devm_gpio_request_one()
to fail. So devm_gpio_request_one() must be called prior to calling
gpio_set_debounce().
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

(edev->extcon_dev_type.groups) has been freed before device_unregister.
extcon_dev_unregister -> kfree(edev->extcon_dev_type.groups)
then device_unregister -> device_del -> device_remove_attrs
-> device_remove_groups(dev, type->groups);
panic because type->groups has been freed.

This patch is move device_unregister ahead of groups free
to avoid panic in extcon_dev_unregister.

stack
[ 22.847226] BUG: unable to handle kernel paging request at 5f39746e
[ 22.847234] IP: [<c1387fcd>] sysfs_remove_group+0x2d/0xd0
[ 22.847238] *pdpt = 0000000000000000 *pde = 0000000000000000
[ 22.847241] Oops: 0000 [#1] PREEMPT SMP
[ 22.847244] Modules linked in:
[ 22.847249] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 3.10.16-261140-g6533774 #1
[ 22.847251] task: f3078000 ti: f3072000 task.ti: f3072000
[ 22.847254] EIP: 0060:[<c1387fcd>] EFLAGS: 00010206 CPU: 0
[ 22.847257] EIP is at sysfs_remove_group+0x2d/0xd0
[ 22.847259] EAX: 00000004 EBX: 5f39746e ECX: 00000000 EDX: f2773560
[ 22.847261] ESI: f2653b80 EDI: f2773560 EBP: f3073c90 ESP: f3073c70
[ 22.847263] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 22.847264] CR0: 8005003b CR2: 5f39746e CR3: 020e5000 CR4: 001007f0
[ 22.847266] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 22.847268] DR6: ffff0ff0 DR7: 00000400
[ 22.847269] Stack:
[ 22.847276] c13848c9 c1ae3805 f3073c80 f24ddc4c 00000246 f2773e88 f1c44408 f2531340
[ 22.847283] f3073ca0 c16935ca f1c44400 f27d3340 f3073cb4 c1693858 f24ddc44 f1c44400
[ 22.847289] f1c4420c f3073cc8 c1693f76 f1c44400 00000001 00000000 f3073ce8 c1694011
[ 22.847290] Call Trace:
[ 22.847295] [<c13848c9>] ? sysfs_hash_and_remove+0x49/0xa0
[ 22.847300] [<c1ae3805>] ? sub_preempt_count+0x55/0xe0
[ 22.847306] [<c16935ca>] device_remove_groups+0x2a/0x40
[ 22.847309] [<c1693858>] device_remove_attrs+0x38/0x60
[ 22.847313] [<c1693f76>] device_del+0xd6/0x150
[ 22.847316] [<c1694011>] device_unregister+0x21/0x60
[ 22.847320] [<c13869e8>] ? sysfs_remove_link+0x18/0x30
[ 22.847323] [<c1697d04>] ? class_compat_remove_link+0x34/0x50
[ 22.847329] [<c18bf5d9>] extcon_dev_unregister+0xf9/0x130
[ 22.847333] [<c18bd21f>] pwrsrc_extcon_dev_reg_callback+0x7f/0xa0
[ 22.847337] [<c1ae36e3>] notifier_call_chain+0x43/0x60
[ 22.847343] [<c12634e1>] __blocking_notifier_call_chain+0x41/0x80
[ 22.847347] [<c126353f>] blocking_notifier_call_chain+0x1f/0x30
[ 22.847351] [<c18bef39>] extcon_dev_notify_add_device+0x19/0x20
[ 22.847354] [<c18bf074>] extcon_dev_register+0x134/0x580
[ 22.847358] [<c1ae3805>] ? sub_preempt_count+0x55/0xe0
[ 22.847363] [<c154b4da>] ? gpiod_request+0x6a/0x1d0
[ 22.847368] [<c132528a>] ? kmem_cache_alloc_trace+0xaa/0x170
[ 22.847372] [<c18c0179>] ? fsa9285_probe+0x99/0x3f0
[ 22.847375] [<c18c00e0>] ? fsa9285_irq_handler+0xf0/0xf0
[ 22.847379] [<c18c019f>] fsa9285_probe+0xbf/0x3f0
[ 22.847383] [<c18c00e0>] ? fsa9285_irq_handler+0xf0/0xf0
[ 22.847388] [<c1828d9e>] i2c_device_probe+0x7e/0xf0
[ 22.847392] [<c1386e52>] ? sysfs_create_link+0x22/0x40
[ 22.847395] [<c1696c62>] ? driver_sysfs_add+0x72/0xa0
[ 22.847399] [<c1697119>] driver_probe_device+0x79/0x360
[ 22.847403] [<c1697491>] __driver_attach+0x91/0xa0
[ 22.847407] [<c1697400>] ? driver_probe_device+0x360/0x360
[ 22.847410] [<c16955a2>] bus_for_each_dev+0x42/0x80
[ 22.847414] [<c1696bee>] driver_attach+0x1e/0x20
[ 22.847417] [<c1697400>] ? driver_probe_device+0x360/0x360
[ 22.847420] [<c169675f>] bus_add_driver+0xef/0x270
[ 22.847425] [<c1828e10>] ? i2c_device_probe+0xf0/0xf0
[ 22.847428] [<c1828e10>] ? i2c_device_probe+0xf0/0xf0
[ 22.847432] [<c1697a8a>] driver_register+0x6a/0x160
[ 22.847436] [<c1addb3d>] ? mutex_unlock+0xd/0x10
[ 22.847440] [<c1438ab2>] ? __create_file+0x122/0x2a0
[ 22.847446] [<c20557d3>] ? extcon_class_init+0x15/0x15
[ 22.847450] [<c1827cbb>] i2c_register_driver+0x2b/0xd0
[ 22.847454] [<c1438d05>] ? debugfs_create_file+0x35/0x40
[ 22.847458] [<c20557d3>] ? extcon_class_init+0x15/0x15
[ 22.847461] [<c20557e4>] fsa9285_extcon_init+0x11/0x29
[ 22.847465] [<c12001aa>] do_one_initcall+0xba/0x170
[ 22.847471] [<c2012b4a>] kernel_init_freeable+0x119/0x1b8
[ 22.847475] [<c20124d3>] ? do_early_param+0x7a/0x7a
[ 22.847480] [<c1ac4090>] kernel_init+0x10/0xd0
[ 22.847485] [<c1ae6cf7>] ret_from_kernel_thread+0x1b/0x28
[ 22.847488] [<c1ac4080>] ? rest_init+0x80/0x80
Tested-by: NLiu, Chuansheng <chuansheng.liu@intel.com>
Reviewed-by: NLiu, Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Nxiaoming wang <xiaoming.wang@intel.com>
Signed-off-by: NZhang Dongxing <dongxing.zhang@intel.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

In the case of a device tree system there will be no pdata attached to
the device, causing us to deference a NULL pointer. Better to take the
pdata from the Arizona structure as this will always exist and we know
will have been populated since it is populated by the MFD device which
binds in the extcon driver.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

This patch remove extcon_dev_register()'s second parameter which means
the pointer of parent device to simplify prototype of this function.
So, if extcon device has the parent device, it should set the pointer of
parent device to edev.dev.parent in extcon device driver instead of in
extcon_dev_register().

Cc: Graeme Gregory <gg@slimlogic.co.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

The extcon device must always need 'struct device' so this patch change
field type of 'dev' instead of allocating memory for 'struct device' on
extcon_dev_register() function.
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <cw00.choi@samsung.com>

Every other pdata field is specified unshifted the patch handles
shifting for the MICBIAS from the microphone detection polarity
configurations in the extcon driver rather than demanding it in
pdata to match other fields.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

We should move range when the measured value is greater than or equal to
the max value not when greater than.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

This patch add 'gpio_active_low' field to 'struct gpio_extcon_data'
to check whether gpio active state is 1(high) or 0(low).
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

This patch use gpio_set_debounce() API provided from gpiolib if SoC or device
driver with gpio support gpio_set_debounce() function.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

Fixes the following warning:
WARNING: space prohibited before semicolon
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

Fixes an incomplete comment introduced by commit 9c2ba270
("extcon: arizona: Simplify HPDET based identification").
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

We want the trig_sts bits to be cleared in all cases where we consider
the jack detection interrupt to have been handled. Specifically, if a
duplicate detection event was suppressed these bits were not cleared
causing the CODEC to not enter a low power state. This patch clears the
bits on the duplicate detection code path.
Reported-by: NRyo Tsutsui <ryo.tsutsui@wolfsonmicro.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

Fixes the following warning:
WARNING: space prohibited before semicolon
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

This fixes up braces coding style issue by using checkpatch script.

Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch remove unnecessary extern declaration (extcon_set_state).
checkpatch found this coding style issue.
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fix 80 column coding sytle issues by using checkpatch script.

Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The debounce timeout is generally quite long and the work not performance
critical so allow the scheduler to run the work anywhere rather than in
the normal per-CPU workqueue.
Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

The debounce timeout is generally quite long and the work not performance
critical so allow the scheduler to run the work anywhere rather than in
the normal per-CPU workqueue.
Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

None of the delayed work the driver schedules has particularly short delays
and it is not performance sensitive so let the scheduler run it wherever
is most efficient rather than in a per CPU workqueue by using the system
power efficient workqueue.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

Based on system design, platform needs to detect the VBUS or ID or
both. Provide option to select this through platform data to
disable part of cable detection through palmas-usb.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Acked-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

Add suspend/resume callbacks and support for wakeup from
suspend on USB HOST or USB Device cable insertion or removal.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Acked-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

When integrating driver with Tegra platform, it is found that
the ID pins get detected only once after booting system and
further removal and re-insert does not detect the ID pin.

Fixing this issue with enabling interrupt on ID_GND and ID_FLOAT
always  and clearing the status on LATCH register which actually
occurred.

Also if interrupt occurs with line status as zero then based on
previous status, set the cable state.

Add debug prints to display the cable state when any cable
insertion/removal happen.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Acked-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

of_extcon_get_extcon_dev() uses dev_name for getting the reference
to the extcon device. If the extcon driver assigns a different
name other than dev_name, of_extcon_get_extcon_dev() wouldn't
be able to find the reference to the extcon device. Since the
client drivers of extcon-palmas would be using
of_extcon_get_extcon_dev(), removed assigning edev.name
in extcon-palmas.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

Added an API of_extcon_get_extcon_dev() to be used by drivers to get
extcon device in the case of dt boot (this can be used instead of
extcon_get_extcon_dev()).
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

The dev_attrs field of struct class is going away soon, dev_groups
should be used instead.  This converts the extcon_class code to use the
correct field.

Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Chanwoo Choi<cw00.choi@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Calling dev_set_name with a single paramter causes it to be handled as a
format string.  Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents,
including wrappers like device_create*() and bdi_register().
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is the driver for the USB comparator built into the palmas chip. It
handles the various USB OTG events that can be generated by cable
insertion/removal.
Signed-off-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NRuchika Kharwar <ruchika@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
[kishon@ti.com: adapted palmas usb driver to use the extcon framework]
Signed-off-by: NSebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Added EXPORT_SYMBOL_GPL() for extcon_register_interest and
extcon_register_notifier in order to avoid undefined reference
error when building the consumer modules of extcon as _modules_.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch change permission from read/write to only read.
The specific process in the user-space couldn't change the state
of cable when cable is attached or detached.
- /sys/class/extcon/[devine name]/state
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>