Hostapd request disconnect for broadcast bssid when it
wants to disconnect all stations from the AP.

Detect this and really disconnect all connected stations.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When allocating pmc descriptor, the structure is
initially created on stack and later copied to
the physical ring (device) memory. The descriptor
structure must be initialized to zero to avoid
garbage configuration, which may result in pmc
mechanism malfunctioning.
Signed-off-by: NVladimir Shulman <QCA_shulmanv@QCA.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Print firmware and ucode assert codes when firmware crashed.
Signed-off-by: NLior David <liord@qti.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

On Rx, when invalid frame is received and dropped,
reaping of next frames from Rx ring is stopped.

This stops NAPI polling and re-enables the Rx interrupt.

However, in cases where no more frames received,
interrupt will not be triggered and rest of Rx frames
will not be processed.

Skip bad frames and continue to reap Rx packets when
such frames are encountered, and add statistics for
such frames for debug.
Signed-off-by: NHamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix compilation warning where CONFIG_PM defined while
CONFIG_PM_SLEEP is not defined

Report follows:

tree:   git://github.com/kvalo/ath pending
head:   941145fc5e5afbb120271e5dfaf37213ddb55807
commit: df596be39294d9712e5d568063a48448031e0a9f [37/39] wil6210: system power management
config: xtensa-allyesconfig (attached as .config)
reproduce:
  wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
  chmod +x ~/bin/make.cross
  git checkout df596be39294d9712e5d568063a48448031e0a9f
  # save the attached .config to linux build tree
  make.cross ARCH=xtensa

All warnings (new ones prefixed by >>):

>> drivers/net/wireless/ath/wil6210/pcie_bus.c:264:12: warning: 'wil6210_suspend' defined but not used [-Wunused-function]
    static int wil6210_suspend(struct device *dev, bool is_runtime)
               ^
>> drivers/net/wireless/ath/wil6210/pcie_bus.c:291:12: warning: 'wil6210_resume' defined but not used [-Wunused-function]
    static int wil6210_resume(struct device *dev, bool is_runtime)
               ^
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The current number of spatial streams used by the client is advertised
as a separate IE in assoc request. Use this information to set
the NSS operating mode.

Fixes: 45c9abc0 ("ath10k: implement more versatile set_bitrate_mask").
Signed-off-by: NVivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

After processing received packets from copy engine, host will allocate
new buffer and queue them back to copy engine ring for further
packet reception. On post rx processing path, skb allocation and
dma mapping are unnecessarily handled within ce_lock. This is affecting
peak throughput and also causing more CPU consumption. Optimize this
by acquiring ce_lock only when accessing copy engine ring and moving
skb allocation out of ce_lock.

In AP148 platform with QCA99x0 in conducted environment, UDP uplink peak
throughput is improved from ~1320 Mbps to ~1450 Mbps and TCP uplink peak
throughput is increased from ~1240 Mbps (70% host CPU load) to ~1300 Mbps
(71% CPU load). Similarly ~40Mbps improvement is observed in downlink
path.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is noticed that pci wakeup time is exceeding current timeout (10ms)
randomly which is tested on QCA988x. So, the wake up time is increased
to 30 ms and added debug prints to log total timeout.
Signed-off-by: NMaharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k driver is using dma_pool_alloc per packet and dma_pool_free
in coresponding at Tx completion.
Use of pre-allocated DMA buffer in Tx will improve saving CPU resource
by 5% while it consumes about 56KB memory more as trade off.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k is using Native WiFi mode as default mode for both of
Tx and Rx path, but it could be changed when driver registers
with a module parameter for specific purpose such as mesh.

The Rx decap mode sent to firmware during WMI initialization should
use the same mode that driver configured at its registration stage
in case of using raw mode, so that host driver receives MAC frame
header containing necessary fields such as QoS and Mesh Control
and uses them in right way to make data traffic work.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The Transmit Power Control (TPC) dump will show the power control values for
each rate which makes it easier to debug calibration problems.

Example usage:

# cat /sys/kernel/debug/ieee80211/phy0/ath10k/tpc_stats
TPC config for channel  5180  mode  10

CTL             = 0x10 Reg. Domain              = 58
Antenna Gain    = 1    Reg. Max Antenna Gain    = 0
Power Limit     = 34   Reg. Max Power           = 34
Num tx chains   = 3    Num supported rates      = 155

**********CDD POWER TABLE*******

No.  Preamble Rate_code tpc_valu1 tpc_value2 tpc_value3
0       CCK     0x40       0            0       0
1       CCk     0x41       0            0       0

[...]

154     HTCUP   0x 0       24           0       0
**********STBC POWER TABLE******
No.  Preamble Rate_code tpc_valu1 tpc_value2 tpc_value3
0       CCK     0x40       0            0       0

[...]

154     HTCUP   0x 0       24           24      0
**********TXBF POWER TABLE******

is used to dump the tx power control stats.
Signed-off-by: NMaharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Copy a_sle32_to_cpu() from ath6kl so that we can easily handle signed __le32
values. This is needed in struct wmi_pdev_tpc_config_event.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

from checkpatch:

drivers/net/wireless/ath/ath10k/mac.c:1113: line over 90 characters
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

checkpatch found:

drivers/net/wireless/ath/ath10k/core.c:574: Blank lines aren't necessary before a close brace '}'
drivers/net/wireless/ath/ath10k/mac.c:4067: Missing a blank line after declarations
drivers/net/wireless/ath/ath10k/mac.c:4083: Missing a blank line after declarations
drivers/net/wireless/ath/ath10k/mac.c:4084: spaces required around that '>>=' (ctx:WxV)
drivers/net/wireless/ath/ath10k/pci.c:1507: Missing a blank line after declarations
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

drivers/net/wireless/ath/ath10k/wmi.c:3023: void function return statements are not generally useful
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

drivers/net/wireless/ath/ath10k/htt_tx.c:457: braces {} are not necessary for single statement blocks
drivers/net/wireless/ath/ath10k/htt_tx.c:545: braces {} are not necessary for single statement blocks
drivers/net/wireless/ath/ath10k/mac.c:200: braces {} are not necessary for single statement blocks
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

checkpatch found:

drivers/net/wireless/ath/ath10k/core.c:513: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/core.c:1266: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1267: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1268: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1269: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/mac.c:4659: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6271: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/pci.c:2260: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/wmi.c:3510: Alignment should match open parenthesis
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

checkpatch found:

drivers/net/wireless/ath/ath9k/core.c:490: Logical continuations should be on the previous line
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Major changes in ath10k:

* add spectral scan support for 10.4 firmware
* add qca6164 support
* implement mesh support using firmware raw mode

There were several bugs here.

1)  The done label was in the wrong place so we didn't copy any
    information out when there was no command given.

2)  We were using PAGE_SIZE as the size of the buffer instead of
    "PAGE_SIZE - pos".

3)  snprintf() returns the number of characters that would have been
    printed if there were enough space.  If there was not enough space
    (and we had fixed the memory corruption bug #2) then it would result
    in an information leak when we do simple_read_from_buffer().  I've
    changed it to use scnprintf() instead.

I also removed the initialization at the start of the function, because
I thought it made the code a little more clear.

Fixes: 5e6e3a92 ('wireless: mwifiex: initial commit for Marvell mwifiex driver')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add calls to netif_carrier_on and netif_carrier_off
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

IW_AUTH_ALG_OPEN_SYSTEM is ambiguous in set_auth for WEP as
wpa_supplicant uses it for both no encryption and WEP open system.
Cache the last mode set (only of these two) and use it here.

This allows wpa_supplicant to work with unencrypted APs.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It's used locally only.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It isn't used anywhere out of ssb code and we don't (plan to) build
pcihost_wrapper.c as a separated module.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

of_default_bus_match_table was not exported earlier, so it could only
be accessed by code compiled into the kernel. A new function
of_platform_default_populate() was added which uses
of_default_bus_match_table and this function is also exported. This way
it is possible to create a bus with the content of
of_default_bus_match_table and we can remove the hacks from bcma.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

brcmfmac uses atomic_or() and other atomic_* functions, but does not
include linux/atomic.h. This file gets included by some other header
file so this normally does not cause problems.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TDLS events are mapped back to primary interface but when p2p is in
use then this fails because the check was incorrect by checking
bsscfg number. Which can be different when a p2p device has been
created.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

There is a workaround needed for p2p device setup which breaks tdls
functionality. This patch fixes that by properly signalling fweh that
p2p device setup is ongoing.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for the BCM4365 and BCM4366 11ac Wave2
PCIE devices.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When p2p device interface gets deleted by deinitialising discovery
it will result in an event which removes the interface, but that is
also done by delete p2p interface code. This results in race
condition which sometimes results in lockup/crash. With this patch
the delete device interface will wait for the event (with timeout)
removing the possible race condition. Also on the stop device call
from cfg80211 the deinitialisation of the discovery device should
be avoided as it can result in a similar situation.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For debugging purpose it is very handy to be able to disable
features. It has happened a few times that new features turned
out not always being properly detected for all devices/firmwares.
Making it possible to disable the feature with a module parameter
will make testing/debugging easier.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some devices with older firmwares are reporting new p2p device
interface with the wrong type. Accept this type to get p2p
working for these devices.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In some situations it is possible that vif has been removed while
cfg80211 invokes the p2p_stop_device handler. This will result in
crash.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When a p2p device gets deleted, the memory for the vif is not being
released. This is solved by reorganizing the cleanup path and
properly freeing the memory.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Different wpa_supplicants have different behavior and expectations
regarding the change_virtual_intf behavior. This patch implements
a workaround for the different versions and possible brcmfmac
configuration.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

p2pon module param is currently under define BRCMDBG. Though it is
a needed option for older versions of the wpa_supplicant which do not
support the P2P_DEVICE interface.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The hash index stored in the flowrings is of type u16 but gets
stored in u8. This can result in incorrect indexing and possibly
result in crashes. This patch fixes the type.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When the p2pon module param is used then p2p attach will initialize
p2p device iface in the firmware, but it is doing that by checking
data. It is cleaner to pass the p2pon information to p2p by API.
This information is also needed for other patch.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>