Janusz reported that the EOSP bit in mac80211 was
getting cleared all the time. I had not found this
since I tested uAPSD with a device that always set
the bit itself. Preserve the bit when building the
QoS header.
Reported-by: NJanusz Dziedzic <janusz.dziedzic@gmail.com>
Tested-by: NJanusz Dziedzic <janusz.dziedzic@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

WPI-SMS4 uses 16-octet PN field, so we need to allow longer key
sequence values to be configured.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This value is used for WPI-SMS4 in ISO/IEC JTC 1 N 9880.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The vif might be busy while reconfiguring
(e.g. associated), so indicate BSS_CHANGED_IDLE as well.
Reported-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Looks like no one uses it.
Signed-off-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Based on a quick test, TDLS seemed to be working fine with ath9k, so
let's start advertising support for this in the driver.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The pointer returned by cfg80211_inform_bss is a referenced
struct. The orinoco driver does not need to keep the struct, so
we just release it.
Signed-off-by: NDavid Kilroy <kilroyd@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch fixes rndis_wlan to release referenced BSS structure returned by
cfg80211_inform_bss().
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This function returns a referenced BSS struct
(or NULL), annotate with __must_check. It seems
that a lot of drivers get this completely wrong
and leak all BSS structs as a result.
Reported-by: NAdam Mikuta <Adam.Mikuta@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

802.11n-2009 extends the supported rates element with a
magic value which can be used to prevent legacy stations
from joining the BSS.

However, this magic value is not a rate like the others
and the magic can simply be ignored/skipped at this late
stage.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>---
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Conflicts:
	net/bluetooth/l2cap_sock.c
	net/bluetooth/mgmt.c

Now that pending commands are hci_dev specific there's no need to check
whether a command matches hci_dev when iterating through them.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

For consistency the integer type should be u16 and not __u16.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The cancel_delayed_work_sync function should not be used if we hold any
locks. Luckily all places where this is the case it is also safe to use
the non-sync version.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Now that the pending commands are within struct hci_dev we can properly
control access to them throught the hci_dev locking mechanism.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch moves the pending management command list (previously global
to mgmt.c) into struct hci_dev. This makes it possible to do proper
locking when accessing it (through the existing hci_dev locks) and
thereby avoid race conditions.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The current global pending command list in mgmt.c is racy. Possibly the
simplest way to fix it is to have per-hci dev lists instead of a global
one (all commands that need a pending struct are hci_dev specific).
This way the list can be protected using the already existing per-hci
dev lock. To enable this refactoring the first thing that needs to be
done is to ensure that the mgmt functions have access to the hci_dev
struct (instead of just the dev id).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NAshok Nagarajan <anagar6@uic.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set peer's HT capabilities, and disallow peering if we're on a different
channel type.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NAshok Nagarajan <anagar6@uic.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NAshok Nagarajan <anagar6@uic.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some refactoring for IBSS HT.

Move HT info and capability IEs building code into separate functions.

Add function to get the channel type from an HT info IE.
Signed-off-by: NAlexander Simon <an.alexsimon@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove most references to magic numbers, save a few bytes and hopefully
improve readability.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The initval tables are updated as per system team input to improve
rx performance and power accuracy at 5GHz.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9462 chips have the capabilities to provoide bluetooth
profile information. For non-AR9462 btcoex chips, the BT
priority traffic was identified by periodically polling
the respective registers and updated dutycycle, stomptype,
etc. As AR9462 chip offers the BT profile informations,
let us make use of that to update aggregation limit,
dutycycle, stomptype and wieghtages.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To improve CCK sensitivity for AR9462 chips, performing
spur mitigation at 2440, 2464 frequencies alone is sufficient.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some cards can generate CCMP IVs in HW, but require the space for the IV
to be pre-allocated in the frame at the correct offset. Add a key flag
that allows us to achieve this.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

genlmsg_end() cannot fail, it just returns the length
of the message. Thus, error handling for it is useless.
While removing it, I also noticed a useless variable
and removed this it as well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The buffer endianess conversion functions in srom.c had a size
argument giving number of bytes but the function converts words.
Providing the number of words to the function is more sensible
so that is done in this patch.
Reported-by: NPavel Roskin <proski@gnu.org>
Reported-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The usage of state decrease readability. Optimize the code flow to
get rid of it
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make a proper use of private data area of net device by storing
interface related data structure instead of generic driver data
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use brcmf_add_if for primary and virtual net device interfaces. This
is part of the net device interface clean up for fullmac.
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the receive path the frames are obtained from the dma using
multiple sk_buff that were linked using the skb next pointer.
This has been changed and it now used sk_buff lists and skb_queue
functions instead.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions ltoh16_buf() and htol16_buf() have been renamed
to le16_to_cpu_buf() and cpu_to_le16_buf() for more clarity
what it does.
Reported-by: NJoe Perches <joe@perches.com>
Reported-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver currently only supports STA operation. However, in
brcms_ops_add_interface() also AP and SSID mode were accepted.
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NRoland Vossen <rvossen@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Monitor mode functionality (not functional yet) requires transmit to be
muted after ops_start() is called, transmit is unmuted when the first
interface is added.
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NRoland Vossen <rvossen@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Upon ops_start(), a Mac80211 driver should enable receive functionality to
support monitor mode. Also, upon ops_stop(), it should disable rx.

Driver did not follow this rule so code has been changed.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NRoland Vossen <rvossen@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Transmit was muted in two ways: full mute and a partial mute called
'pre ism cac time' mute. But, this 'pre ism cac time' mute was done at
one place in the code (when tx_mute == false), and overridden later
on in another place in code.

To fix this, the 'pre ism cac time' mute has been replaced by a non
mute.
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NRoland Vossen <rvossen@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>