This patch fixes a warning in clk_enable by calling clk_prepare_enable
instead.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cpts driver tries to obtain the input clock frequency by calling the
clock's internal 'recalc' method. Since <plat/clock.h> has been removed,
this code can no longer compile.

However, the driver never makes use of the frequency value, so this patch
fixes the issue by removing the offending code altogether.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove some __dev* markings that snuck in the 3.8-rc1 merge window in
the drivers/net/* directory.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Retries active opens for INUSE errors.

Logs any active ofld_connect_wr error replies.

Sends ofld_connect_wr on same ctrlq. It needs to go  on the same control txq as
regular CPL active/passive messages.

Retries on active open replies with EADDRINUSE.

Uses active open fw wr only if active filter region is set.

Adds stat for ofld_connect_wr failures.

This patch also adds debugfs file to show endpoints.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

It establishes passive open connection through firmware work request. Passive
open connection will go through this path as now instead of listening server we
create a server filter which will redirect the incoming SYN packet to the
offload queue. After this driver tries to establish the connection using
firmware work request.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

It enables establishing active open connection using fw_ofld_connection work
request when cpl_act_open_rpl says TCAM full error which may be because
of LE hash collision. Current support is only for IPv4 active open connections.

Sets ntuple bits in active open requests. For T4 firmware greater than 1.4.10.0
ntuple bits are required to be set.

Adds nocong and enable_ecn module parameter options.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>

[ Move all FW return values to t4fw_api.h.  - Roland ]
Signed-off-by: NRoland Dreier <roland@purestorage.com>

commit:  cb64edb6 upstream

Above commit may introduce a race between cp_interrupt and dev_close
/ change MTU / dev_open up state. Changes cp_interrupt to tolerate
this.  Change spin_locking in cp_interrupt to avoid possible
but unobserved race.
Reported-by: N"Francois Romieu" <romieu@fr.zoreil.com>

Tested on virtual hardware, Tx MTU size up to 4096, max tx payload
    was ping -s 4068 for MTU of 4096. No real hardware, need test
    assist.
Signed-off-by: N"John Greene" <jogreene@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: "David Woodhouse" <David.Woodhouse@intel.com>
Tested-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add CONFIG_OF guard and use of_match_ptr macro.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ksz884x driver does receive processing in a custom tasklet, and
seems to be assuming that since it takes its private interface spinlock
with spin_lock_irq(), it won't be running concurrently with its own
interrupt handler, as it cannot be preempted by it, but since its
interrupt handler doesn't do any locking whatsoever, the receive
processing tasklet and interrupt handler can end up running concurrently
on different CPUs.

As a result of this, the ksz884x receive path ends up locking up fairly
easily, when the receive processing tasklet's reenabling of receive
interrupts (due to it being done with polling the receive ring) races
with the interrupt handler's disabling of receive interrupts (due to a
new receive interrupt coming in) resulting in the receive interrupt
being masked but the receive processing tasklet not being scheduled.

Fix this by making the ksz884x interrupt handler take its private
interface spinlock.  This requires upgrading the spin_lock() in the
transmit cleanup tasklet to a spin_lock_irq(), as otherwise the IRQ
handler can preempt transmit cleanup and deadlock the system, but
with those two changes, no more receive lockups have been observed.
Reported-by: NChris Healy <cphealy@gmail.com>
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>

----
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qlcnic_hw.c:370: warning: variable cmd_desc set but not used
qlcnic_hw.c:368: warning: variable consumer set but not used
qlcnic_main.c:448: warning: variable ref_count set but not used
qlcnic_main.c:534: warning: variable mem_base set but not used
qlcnic_ctx.c:137: warning: variable tmp_tmpl set but not used
qlcnic_ctx.c:133: warning: variable version set but not used
qlcnic_minidump.c:200: warning: variable opcode set but not used
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device managed flow steering will be enabled only under administrator
directive provided through setting the existing module parameter
log_num_mgm_entry_size to -1 (if the device actually supports flow
steering).  If flow steering isn't requested or not available, the
driver will use the value of log_num_mgm_entry_size and B0 steering.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Separate flow steering capability detection from the decision to activate.

For the master (and for native), detect the flow steering capability
in mlx4_dev_cap, but activate the appropriate steering type in a new
function choose_flow_steering() based on detected data.

For VFs, activate flow steering based on what was actually activated
by the master, where that info is obtained via QUERY_HCA. This fixes
the current VF detection which is wrongly based on QUERY_DEV_CAP.

Also, for SR-IOV mode, if flow steering may be activated, do so only
if the max number of QPs per rule is sufficient to satisfy one
subscription per VF.  If not, fall back to B0 mode. This is needed to
serve registrations done by L2 network drivers such as mlx4_en and
IPoIB when the network stack attempts to join to multicast groups such
as all-hosts or the IPoIB broadcast group.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The error flow of the flow steering wrapper had a typo which caused
the wrong firmware command to be called, fix it.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Since VFs may be mapped to VMs which aren't trusted entities, flow
steering rules attached through the wrapper on behalf of VFs must be
checked to make sure that the specified QP number is assigned to that
VF.  Also, make sure to keep the QP busy till the end of the operation
from the resource tracker point of view.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

It supports establishing passive open connection through firmware filter work
request. Passive open connection will go through this path as now instead of
listening server we create a server filter which will redirect the incoming SYN
packet to the offload queue.

It divides filter region into regular filters and server filter portion. It
introduces new server filter region which will be exclusively used for creating
server filters. This region will not overlap with regular filter region.

It provides new API cxgb4_alloc_sftid in LLD for getting stid in case of LE
hash collision path. This new stid will be used to open server filter in the
filter region.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The T4 architecture is capable of filtering ingress packets at line rate
using the rule in TCAM. If packet hits a rule in the TCAM then it can be either
dropped or passed to the receive queues based on a rule settings.

This patch adds framework for managing filters and to use T4's filter
capabilities. It constructs a Firmware Filter Work Request which writes the
filter at a specified index to get the work done. It hosts shadow copy of
ingress filter entry to check field size limitations and save memory in the
case where the filter table is large.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Beside imx6q, the kernel built from imx_v6_v7_defconfig is also
supposed to be running on other IMX SoCs that do not have the PTP
block.  Before fec driver gets fixed to run-time detect target hardware
rather than conditional compiling with #ifdef CONFIG_FEC_PTP, let's
give it a quick fix in Kconfig to forbid FEC_PTP on those IMX SoCs that
do not support PTP.
Reported-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RX CQ can report completions with invalid frag_idx when the RXQ that
was *previously* using it, was not cleaned up properly. This hits
a BUG_ON() in be2net.

When completion coalescing is enabled on a CQ, an explicit CQ-notify
(with rearm) is needed for each compl, to flush partially coalesced CQ
entries that are pending DMA.

In be_close(), this fix now notifies CQ for each compl, waits explicitly
for the flush compl to arrive and complains if it doesn't arrive.

Also renaming be_crit_error() to be_hw_error() as it's the more
appropriate name and to convey that we don't wait for the flush compl
only when a HW error has occurred.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In be_close(), be_eq_clean() must be called after all RX/TX/MCC queues
have been cleaned to ensure that any events caused while cleaning up
completions are notified/acked. Not clearing all events can cause
upredictable behaviour when RX rings are re-created in the subsequent
be_open().
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use prandom_bytes() to fill rss key with pseudo-random bytes.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: David Laight <david.laight@aculab.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 87c0e764 (cpts: introduce time stamping code and a PTP hardware clock)
mistakenly included plat/clock.h that should not be included by drivers
even if it exists.

Otherwise we get the following error with at least omap2plus_defconfig:

drivers/net/ethernet/ti/cpts.c:30:24: error: plat/clock.h: No such file or directory

Signed-off-by: Tony Lindgren <tony@atomide.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes platform device drivers unregistering and adds proper error
handing on module loading.
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement destination MAC rule extension for L3/L4 rules in
flow steering. Usefull for vSwitch/macvlan configurations.
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get rid of full_mac, zero_mac in favour of
is_zero_ether_addr and is_broadcast_ether_addr.
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 4ce45e02
"bnx2: Add BNX2 prefix to CHIP ID and name macros"

accidentally reverted 2 commits to use pci_ioumap() and to make
pci_error_handlers const.  This fixes those mistakes.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
 -      Added Stats clear counter to the bfi_enet_stats_mac structure and
        ethtool stats
 -      Modified the firmware naming convention to contain the firmware image
        version (3.1.0.0). The new convention is
        <firmware-image>-<firmware-version>.bin The change will enforce loading
        only compatible firmware with this driver and also avoid over-writing
        the old firmware image in-order to load new version driver as the
        firmware names used to be the same.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
 -      BNA state machine for Rx in start_wait state moves it to stop_wait on
        receipt of RX_E_STOP. In Rx stop_wait state, on receipt of
                RX_E_STARTED event does enet stop
                RX_E_STOPPED event does rx_cleanup_cbfn
        rx_cleanup_cbfn in this case is called without post_cbfn. post_cbfn
        happens only after RX_E_STARTED event is received in start_wait. Without
        doing post_cbfn, NAPI remains disabled and in cleanup we try to disable
        again causing endless wait. ifconfig process and other workers can thus
        get stuck.
 -      Introducing start_stop_wait state for Rx. This state handles the case of
        if post_cbfn is not done simply do stop without the cleanup.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
        Enhanced support for GRO. Page-base allocation method for Rx buffers is
used in GRO. Skb allocation has been removed in Rx path to use always warm-cache
skbs provided by napi_get_frags.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
        For Tx IB, IPM was enabled with inter_pkt_timeo of 0. This caused the
Tx IB not to generate interrupt till inter_pkt_count of packets have been
received. Correct definition for BFI_TX_INTERPKT_TIMEO & BFI_TX_INTERPKT_COUNT
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 -      Have contiguous queue pages for TxQ, RxQ and CQ. Data structure and
        QPT changes related to contiguous queue pages
 -      Optimized Tx and Rx unmap structures. Tx and Rx fast path changes due to
        unmap data structure changes
 -      Re-factored Tx and Rx fastpath routines as per the new queue data structures
 -      Implemented bnad_txq_wi_prepare() to program the opcode, flags, frame_len
        and num_vectors in the work item
 -      Reduced Max TxQ and RxQ depth to 2048 while default value for Tx/Rx queue
        depth is unaltered (512)
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 -      Remove unnecessary prefetch
 -      Simplify checking & comparison of CQ flags
 -      Dereference & store unmap_array, unmap_cons & current unmap_array
        element only once
 -      Make structures tx_config & rx_config cache line aligned.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The {read,write}s{b,w,l} operations are not defined by all
architectures and are being removed from the asm-generic/io.h
interface.

This patch replaces the usage of these string functions in the smc911x
accessors with io{read,write}{8,16,32}_rep calls instead.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: netdev@vger.kernel.org
Signed-off-by: NMatthew Leach <matthew@mattleach.net>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using netdev_alloc_frag() instead of kmalloc() permits better GRO or
TCP coalescing behavior, as skb_gro_receive() doesn't have to fallback
to frag_list overhead.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Dmitry Kravkov <dmitry@broadcom.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The {read,write}s{b,w,l} operations are not defined by all
architectures and are being removed from the asm-generic/io.h
interface.

This patch replaces the usage of these string functions in the 8390
accessors with io{read,write}{8,16,32}_rep calls instead.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NMatthew Leach <matthew@mattleach.net>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The {read,write}s{b,w,l} operations are not defined by all
architectures and are being removed from the asm-generic/io.h
interface.

This patch replaces the usage of these string functions in the default
DM9000 accessors with io{read,write}{8,16,32}_rep calls instead. This
is required as the dm9000 driver is in use by the blackfin
architecture which uses the asm-generic io accessors.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NMatthew Leach <matthew@mattleach.net>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The {read,write}s{b,w,l} operations are not defined by all architectures
and are being removed from the asm-generic/io.h interface.

This patch replaces the usage of these string functions in the default
SMC accessors with io{read,write}{8,16,32}_rep calls instead, which are
defined for all architectures.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GigaMAC registers have been reported left unitialized in several
situations:
- after cold boot from power-off state
- after S3 resume

Tweaking rtl_hw_phy_config takes care of both.

This patch removes an excess entry (",") at the end of the exgmac_reg
array as well.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NWang YanQing <udknight@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>