There is several different SoCs sharing the sun5i codename: A10s, A12
and A13. Since there is enough differences to not consider those the
same SoCs, change a bit the naming scheme to reflect this.

Moreover, some boards like the olinuxino come in A10s and A13 variants,
which also share the same SoC codename.

So change the naming scheme to reflect both the codename and the market
name of the SoCs used in the dtsi and in the board files
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The current rules have the .dtb files build in a different directory
from the .dts files. The only reason for this is that it was what
PowerPC has done historically. This patch changes ARM to use the generic
dtb rule which builds .dtb files in the same directory as the source .dts.

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: NOlof Johansson <olof@lixom.net>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
[swarren: added rm command for old stale .dtb files]
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

This adds hrefprev60, hrefv60plus and ccu9540 to device trees compiled
during build.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>

This adds support for SPEAr320-HMI board.
Signed-off-by: NShiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>

Add support for Plat'Home OpenBlocks A6 using the device tree
where possible.
This commit supports SATA, USB, ether and serial console.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds initial dts file for EXYNOS5440 SoC and adds the
dts file for SSDK5440 board which is a kind of reference board.
More properties will be added later.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This commit converts the 'LaCie Ethernet Disk mini v2' board to the
Device Tree. All devices that have existing Device Tree bindings are
converted over to the Device Tree, the other devices remain
instantiated in the old way, until the respective drivers get the
needed Device Tree bindings.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NStefan Peter <s.peter@mpl.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Hello, Andrew

> > +#define NSA310_GPIO_LED_ESATA_GREEN	12
> > <..>
> > +#define NSA310_GPIO_POWER_OFF		48
>
> It looks like most of these are not used. Please remove them.

True. Fixed.

> > +static struct mtd_partition nsa310_mtd_parts[] = {
> > +	{
> > +		.name	= "uboot",
> > +		.offset	= 0,
> > +		.size	= 0x100000,
> > +		.mask_flags = MTD_WRITEABLE,
> > +	}, {
> > <..>
> You should be able to put all that into DT. Take a look at

Correct. I did the conversion and tested that the partitions
can be read with dd and produce exactly the same data before and
after conversion. So, the partition offsets at least should be fine.

> > +static struct i2c_board_info __initdata nsa310_i2c_info[] = {
> > +	{ I2C_BOARD_INFO("adt7476", 0x2e) },
> > +};
>
> You can also do this in DT as well. kirkwood-ts219.dtsi has
>
>                 i2c@11000 {
>                         status = "okay";
>                         clock-frequency = <400000>;

Ok, I did convert the i2c definition to use the devicetree.
The adt7476 device itself is not at reach of device tree,
AFAIK and requires more work at there?

Thanks for your valuable comments. Following is a new patch that
should address the problems and mistakes you pointed and also
some of the pointed by Jason Cooper. The nand and i2c are now
defined at DT and I also removed the pointless defines and
ARM_APPENDED_DTB. It is based against the Linus' official
3.6 version.

Best regards,
Tero
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This is a new kirkwood box made by Universal Scientific Industrial, Inc.
The product description is here:

http://www.usish.com/english/products_topkick1281p2.php

It is very similar to the dreamplug and other plug devices, with the
exception that it has room for a 2.5" SATA HDD internally.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

This patch adds DT board setup for the LaCie NAS Network Space Mini v2
(aka SafeBox). The hardware characteristics are very close to those of
the Network Space Lite v2. The main difference are:
- A GPIO fan which is only available on the NS2 Mini.
- A single USB host port is wired on the NS2 Mini. The NS2 Lite provides
  an additional dual-mode USB port (host/device).
Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds DT board setup for the LaCie NAS Network Space Lite v2.
This board is derived from the Network Space v2 and a lot of hardware
characteristics are shared.

- CPU: Marvell 88F6192 800Mhz
- SDRAM memory: 128MB DDR2 200Mhz
- 1 SATA port: internal
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports: host and host/device
- 1 push button
- 1 SATA LED (bi-color, blue and red)

Note that the SATA LED is not compatible with the driver leds-ns2. The
LED behaviour ("on", "off" or "SATA activity blink") is controlled via
a single MPP (21).
Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds DT board setup for LaCie Network Space v2 and parents,
based on the Marvell Kirkwood 6281 SoC. This includes Network Space v2
(Max) and Internet Space v2.
Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This dts file is based on the Snow dts file in the Chromium OS kernel
tree with the following changes:
* Some details have been updated to match the exynos5250-smdk5250.dts
  file from linux-next (as of c11068538994430547722dc9fb515a0ceefd5cb9).
* This file doesn't include references to hardware whose upstream
  support isn't quite there yet.  That includes most i2c devices.
  Note that most i2c busses have been included with no devices.

The Snow dts file is mostly just an include of the "cros5250" dts file
which describes a class of similar boards. Support for other boards has
not yet been send upstream.

With this file and a change to use UART3 for serial output I can:
* Boot to a command line using either SD or EMMC as a root filesystem
* See the power button and lid switch using evtest.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds support for the Cubieboard based on the Allwinner
A10/sun4i SoC. Currently only UART is supported. Other devices
will eventually follow.
Signed-off-by: NStefan Roese <sr@denx.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add DTS file for this custom board.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

In order to start upstreaming Broadcom SoC support, create
a starting hierarchy, arch and dts files.
The first support SoC family that is planned is the
BCM281XX (BCM11130/11140/11351/28145/28155) family of dual A9 mobile
SoC cores.
This code is just the skeleton code for get the machine upstreamed. It
has been made MULTIPLATFORM compatible.
Next steps
----------
Upstream a basic set of drivers - sufficient for a console boot to
ramdisk. These will includer timer, gpio, i2c drivers.
After this basic set, we will proceed with a more comprehensive set
of drivers for the 281XX SoC family.

v2 patch mods
--------
 - Remove l2x0_of_init call as there were problems with the code.
   A separate patch will be submitted with cache init code
 - Rename capri files and refs to bcm281xx-based names
 - Add bcm281xx binding doc
 - various misc cleanups

v3 patch mods
-------------
 - Remove extra #include lines
 - Remove remaining references to capri
 - dt uart chipset string added
 - cleaned up chip # references

v4 patch mods
-------------
 - swap order of compatible definitions for uart
 - fix typo

v5 patch mods
-------------
 - Rename bcm281xx to bcm11351 in dts+code,
   leaving references to bcm281xx only in help+comments.

v6 patch mods
-------------
 - fix typo in uart 'compatible' string
Signed-off-by: NChristian Daudt <csd@broadcom.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The dtb targets belong in arch/arm/boot/dts/Makefile now, so move the
newly added davinci targets there.
Signed-off-by: NOlof Johansson <olof@lixom.net>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

CPU Module with ATMEL AT91SAM9G45
http://www.ronetix.at/pm9g45.htmlSigned-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input

Add very basic support for it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This platform, available from Globalscale has an Armada 370. For now,
only the serial port is supported. Support for network, USB and other
peripherals will be added as drivers for them become available for
Armada 370 in mainline.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
This is 3.8 material.

Changes from original version posted by Gregory:
 * Renamed .dts file to armada-370-mirabox.dts
 * Change compatible string to 'globalscale,mirabox'
 * Remove compatible string from armada-370-xp.c
 * Removed references to MBX0001

This platform, available in Japan from PlatHome, has a dual-core
Armada XP, the MV78260. For now, only the two serial ports and the
three front LEDs are supported. Support for SMP, network, SATA, USB
and other peripherals will be added as drivers for them become
available for Armada XP in mainline.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

---
This is 3.8 material.

Changes since v2:

 * Renamed the .dts file to armada-xp-openblocks-ax3-4.dts

 * Removed the compatible string from armada-370-xp.c (which now only
   lists the common SoC compatible string)

Changes since v1:

 * Renamed the board to OpenBlocks AX3-4, since there is a variant
   called AX3-2 which has less RAM, and no mini PCIe port. Requested
   by Andrew Lunn.

 * Fix the amount of memory to 3 GB. In fact, the board has 1 GB
   soldered, and 2 GB in a SODIMM slot (which is therefore
   removable). But as the board is delivered as is, we'll assume it
   has 3 GB of memory by default.

The purpose of the created zynq-7000.dtsi file is to describe the
hardware common to all Zynq 7000-based boards.  Also, get rid of the
zynq-ep107 device tree, since it is not hardware anyone can purchase.

Add a zc702 dts file based on the zynq-7000.dtsi.  Add it to the
dts/Makefile so it is built with the 'dtbs' target.
Signed-off-by: NJosh Cartwright <josh.cartwright@ni.com>
Acked-by: NMichal Simek <michal.simek@xilinx.com>

Add a minimal board dts file for Samsung EXYNOS4412 based SMDK board.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The EVMSK was not built with the 'make dtbs' command.
Add the missing entry in the dts Makefile.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

The APF28Dev is a docking board for an APF28 SOM
Signed-off-by: NGwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: NJulien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Separate out common dts pieces from highbank dts and add support for
Calxeda ECX-2000 (Midway) SOC.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Use DT_MACHINE_START() on the sh7372 based mackerel board.

Also include a tiny DTS file to describe the board and update the
Kconfig dependencies to select CONFIG_USE_OF.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>

Rename the files to have names consistent across OMAP boards.

Update the Makefile to use the new name.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add a minimal dts for original OMAP3430/3530 version of the Beagle board. This
version of the Beagle board has 256MB of DDR and features the same TWL4030
power management IC (PMIC) as the Beagle board XM.

Given that the Beagle and Beagle-XM boards use the same PMIC, move the
definition of the VSIM regulator into the TWL4030.dtsi file so that we do not
need to duplicate in the Beagle board dts file.

This has been boot tested on an OMAP3530 Beagle board and verifing that the
SD/MMC interface is working with a SD card.

V2 changes
- Rebased upon of devel-dt
- Corrected copyright date in omap3-beagle.dts file
- Added LED support after verifing that Beagle and Beagle XM have the same LED
  configuration
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

The APF28 is a small SOM built around an i.MX28 processor with 128MBytes DDR2,
256MBytes NAND Flash and an Ethernet PHY.
Signed-off-by: NJulien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: NGwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This makes sure that the ARM Integrator device trees get compiled
during build.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Set the dbgu pinctrl config by default as we have only one possible config
For other uart set the rxd/txd by default.

For at91sam9x5ek create soc based dts as we need to include specific soc dtsi.
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This adds am335x-evm and am335x-bone dtb targets to
'make dtbs', just like other platforms.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

We already have CONFIG_ARCH_MXC cover imx5 and imx6 dtb targets.
Remove the redundant ones with CONFIG_ARCH_IMX5 and CONFIG_SOC_IMX6Q.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add board files (vt8500-bv07, wm8505-ref and wm8650-mid)
to allow 'make dtbs' on arch-vt8500.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This moves a few of the newly introduced dtb targets to the common
dts/Makefile instead of the per-platform file.
Signed-off-by: NOlof Johansson <olof@lixom.net>