We need to mask out the port offset from the port number
cached in ld_qdi->timing.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Dual port QDI6580 has shared PIO timings for master/slave
devices so it needs to use custom ->qc_issue method.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Clear old MWDMA timings before programming new ones (IT8213
is a single port host so there is no need to check ap->port_no).

This change should be safe as this is how we have been doing
things in IDE it8213 host driver for years.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

[ port of Sergei's fixes for pata_efar from commit 5f33b3bc ]

Fix the PIO mode 2 using mode 0 timings -- this driver should enable the
fast timing bank starting with PIO2, just like the PIIX/ICH drivers do.
Also, fix/rephrase some comments while at it.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

* do not clear PIO timings for master when programming slave
* program new PIO timings in the correct register nibble

Both changes should be safe as this is how we have been doing
things in IDE it8213 host driver for years.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Driver should program the cycle timing not the mode number
(doing the latter results in wrong timings being used).

There shouldn't be any problems with it as IDE it8213 host driver
has been doing it this way for years.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix ->resume method to re-enable & re-init PCI device properly
before doing chipset specific setup.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

It has been dead for the last three years (== since the initial driver
merge) and probability that it will ever get fixed is quite low.

Since there is no reason to keep this dead code around any longer just
remove it (it can still be retrieved from the git history if necessary).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Do not clear MWDMA timings for device on the other port when
programming slave device.

This change should be safe as this is how we have been doing
things in IDE slc90e66 host driver for years.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

* do not clear PIO timings for master when programming slave
* do not clear PIO timings for device on the other port when
  programming slave device

Both changes should be safe as this is how we have been doing
things in IDE slc90e66 host driver for years.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix erroneous check for ap->udma_mask in do_pata_set_dmamode()
resulting in controller not being programmed properly for MWDMA.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ahci can drive the Promise PDC42819, but obviously it can only use SATA
disks connected to this controller. The controller can actually support
SAS disks as well, but we only know how to use it in it's AHCI mode.

Add a message to let users know that because ahci is driving their chip
they can only use the SATA disks connected to this controller.
Signed-off-by: NMark Nelson <mdnelson8@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
they weren't converted by commit 44c10138
(PCI: Change all drivers to use pci_device->revision).
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The comment in the driver actually describes HPT37x's timing register layout,
which is different from HPT36x.  Fix it and reformat the comment, while at it.

Bump the driver version, accounting for several patches that forgot to do it.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Based on:
http://lkml.indiana.edu/hypermail/linux/kernel/0908.2/01420.htmlSigned-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

These drivers inherited from the older 'hpt366' IDE driver the buggy timing
register masks in their set_piomode() metods. As a result, too low command
cycle active time is programmed for slow PIO modes.  Quite fortunately, it's
later "fixed up" by the set_dmamode() methods which also "helpfully" reprogram
the command timings, usually to PIO mode 4; unfortunately, setting an UltraDMA
mode #N also reprograms already set PIO data timings, usually to MWDMA mode #
max(N, 2) timings...

However, the drivers added some breakage of their own too:  the bit that they
set/clear to control the FIFO is sometimes wrong -- it's actually the MSB of
the command cycle setup time; also, setting it in DMA mode is wrong as this
bit is only for PIO actually and clearing it for PIO modes is not needed as
no mode in any timing table has it set...

Fix all this, inverting the masks while at it, like in the 'hpt366' and
'pata_hpt366' drivers; bump the drivers' versions, accounting for recent
patches that forgot to do it...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We were never able to get docs for this out of Toshiba for years. Dave
Barnes produced a NetBSD driver however and from that we can fill in the
needed tables.

As we correct the PCI identifiers a bit also update the old ide generic driver
at the same time so it stays compiling.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Making the new stuff work broke some of the old chipsets. We need to go
back to the old set up values for these it seems. Unfortunately even with
documentation this is basically a mix of cargoculting and guesswork.

Chased down to the exact line by Gianluca.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Daniela Engert pointed out that there are some implementation notes for the
643 and 646 that deal with certain serialization rules. In theory we don't
need them because they apply when the motherboard decides not to retry PCI
requests for long enough and the chip is busy doing a DMA transfer on the
other channel.

The rule basically is "don't touch the taskfile of the other channel while
a DMA is in progress". To implement that we need to

- not issue a command on a channel when there is a DMA command queued
- not issue a DMA command on a channel when there are PIO commands queued
- use the alternative access to the interrupt source so that we do not
  touch altstatus or status on shared IRQ.

Updated to remote extra conditional check Bartlomiej noted and to remove
the variables for irq checks as the CMD648 doesn't have the underlying problem.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Bartlomiej pointed out that while this got fixed in the old driver whoever
did it didn't port it across.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Reported by Mikulas Patocka.

VIA VT82C586B + Transcend TS64GSSD25-M v0826 does not work in UDMA mode
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add support for the ATA TRIM command in libata.  We translate a WRITE SAME 16
command with the unmap bit set into an ATA TRIM command and export enough
information in READ CAPACITY 16 and the block limits EVPD page so that the new
SCSI layer discard support will driver this for us.

Note that I hardcode the WRITE_SAME_16 opcode for now as the patch to introduce
the symbolic is not in 2.6.32 yet but only in the SCSI tree - as soon as it is
merged we can fix it up to properly use the symbolic name.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

If ATA device failed FLUSH, it means that the device failed to write
out some amount of data and the error needs to be reported to upper
layers. As retries can't recover the lost data, FLUSH failures need to
be reported immediately in general.

However, if FLUSH fails due to transmission errors, the FLUSH needs to
be retried; otherwise, filesystems may switch to RO mode and/or raid
array may drop a drive for a random transmission glitch.

This condition can be rather easily reproduced on certain ahci
controllers which go through a PHY event after powersave mode switch +
ext4 combination.  Powersave mode switch is often closely followed by
flush from the filesystem failing the FLUSH with ATA bus error which
makes the filesystem code believe that data is lost and drop to RO
mode.  This was reported in the following bugzilla bug.

  http://bugzilla.kernel.org/show_bug.cgi?id=14543

This patch makes libata EH retry FLUSH if it wasn't failed by the
device.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NAndrey Vihrov <andrey.vihrov@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Enable device hot-plug support on Port multiplier fan-out ports
Signed-off-by: NAshish Kalra <Ashish.Kalra@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Alan Cox reported that cable detection sometimes works unreliably
for HPT3xxN and that the issue is fixed by adding debounce delay
as used by the vendor driver.

Sergei Shtylyov also noticed that debounce delay is needed for all
HPT37x and HPT3xxN chipsets according to vendor drivers.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The detection was reversed between primary and secondary ports.

Fix it to match hpt366 and the vendor driver.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

sysfs attributes shouldn't require newlines. Make it possible to set the
link power management policy without a trailing newline.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We can use the same ->pre_reset method for all HPT37x chipsets now.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

I obseved there is a sata_async_notification() for every ahci
interrupt. But the async notification does nothing (this is hard
disk drive and no pmp). This cause cpu wastes some time on sntf
register access.

It appears ICH AHCI doesn't support SNotification register, but the
controller reports it does. After quirking it, the async notification
disappears.

PS. it appears all ICH don't support SNotification register from ICH
manual, don't know if we need quirk all ICH. I don't have machines
with all kinds of ICH.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The following patch adds MSI support. Some platforms
may have broken MSI, so those are defaulted to use
legacy PCI interrupts.
Signed-off-by: NVivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Remove the experimental tag on Parallel ATA drivers. Though some of the
individual PATA drivers are still marked as experimental, as a group they can
hardly be considered to be, given they've been used in various distros for some
time.
Signed-off-by: NRobert Hancock <hancockrwd@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use ARRAY_SIZE macro of kernel api instead.
Signed-off-by: NThiago Farina <tfransosi@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

In via_init_one, when via_isa_bridges iterator reaches
PCI_DEVICE_ID_VIA_ANON and last but one via_isa_bridges bridge is
found but rev doesn't match, pci_dev_put(isa) is called twice.

Do pci_dev_put only once.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Tested on IXP425 + CS5536.
Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Missing _SDD is not an error.  Don't treat it as one.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>