Remove some unneeded braces and make a busy loop more obvious.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Some machine_xx_initcall macros were recently added that check for the machine
type before calling the function.  This converts the 4xx platforms to use those
for bus probing.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Remove the declarations for isa_io_base and isa_mem_base as they are declared
in pci-common.c now.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The e200 and e500 platforms are separated in various parts of the kernel with
ifdefs, most notably reg_booke.h and traps.c.  The new machine_check rework
requires them to be similarly separated in cputable.c to avoid compile errors.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Mark the of_device_id structures used to probe the various busses on 4xx
as __initdata.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Enable PCI support for these eval boards among other things.  Also selects
PCI for Rainier in the Kconfig file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch adds basic support for the AMCC Makalu board to arch/powerpc.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Currently we have some limitations in the 4xx PCIe driver and can't
support all possible PCIe busses. But the current limits in the
dts file are quite low (only 16 busses per RC). This patch increases
the number to 64 per RC.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds PCI entry to PowerPC 440GRx Rainier DTS.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Renaming the CPU nodes with generic names put the CPU model in
the "model" property and thus broke the PowerPC 440EP(x)/440GR(x)
identical PVR workaround. The updates it to use the new model property
for CPU identification.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Recent DTC versions disallow certain special characters in full paths without
being quoted with {}.  That however breaks compatibility with older DTC
versions.  Work around this by renaming the CPU nodes for the 4xx files to a
generic node name, and specify the processor type in the model property of the
CPU node.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch sets the ibpre flag (Inbound Presence) for the 405EX
in the 4xx PCIe driver.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The recent changes from Benjamin Herrenschmidt to the ibm_newemac now
make it possible to support other 4xx variants by just defining the
correct properties in the device tree. In this case of the 405EX we
need to define "has-mdio" in the RGMII node and "has-inverted-stacr-oc"
and "has-new-stacr-staopc" in the EMAC node same as on the 440EPx.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

For EMAC support, 405EX needs to be defined to enable the corresponding
EMAC features (IBM_NEW_EMAC_EMAC4, etc.).
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Right now TLB entry 0 ist used as UART0 mapping for the early debug
output (via CONFIG_SERIAL_TEXT_DEBUG). This causes problems when many
TLB's get used upon Linux bootup (e.g. while PCIe scanning behind
bridges and/or switches on 440SPe platforms). This will overwrite the
TLB 0 entry and further debug output's may crash/hang the system.

This patch moves the early debug UART0 TLB entry from 0 to 62 as done
in arch/powerpc. This way it is in the "pinned" area and will not get
overwritten. Also the arch/ppc/mm/44x_mmu.c code is now synced with the
newer code from arch/powerpc.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Update the Rainier wrapper for the libfdt merge and add the pci flags to the
platform file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

A small error caused a header file to be removed making sequoia support no
longer compile.  Fix it.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

PowerPC 440Epx/GRx Sequoia/Rainier updates for 2.6.25
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The mechanism to do the setup for 440A cores changed recently.  This fixes
the 440grx setup function to call __fixup_440A_mcheck.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds PCI entry to PowerPC 440EPx Sequoia DTS.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Correct the PowerPC 440GRx machine check callback.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This is a UIC cascade handler rework to use set_irq_chained_handler() for
cascade, just like othe ppc platforms do. With current implementation we have
additional redirection for irq handler and we call generic_handle_irq twice
(once for the primary uic and the other time for handling cascade interrupt).
This causes Ingo's realtime support patch to stop working on 4xx.

Not sure of any other possible problems though, but with
set_irq_chained_handler() we can abolish "struct irqaction cascade" from the
chip descriptor and call generic_handle_irq() once, directly for cascade irq.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch makes PowerPC 4xx UIC use generic level irq handler instead
of a custom handle_uic_irq() function. We ack only edge irqs in mask_ack
callback, since acking a level irq on UIC has no effect if the interrupt
is still asserted by the device, even if the interrupt is already masked.
So, to really de-assert the interrupt we need to de-assert the external
source first *and* ack it on UIC then. The handle_level_irq() function
masks and ack's the interrupt with mask_ack callback prior to calling
the actual ISR and unmasks it at the end. So, to use it with UIC interrupts
we need to ack level irqs in the unmask callback instead, after the ISR
has de-asserted the external interrupt source. Even if we ack the interrupt
that we didn't handle (unmask/ack it at the end of the handler, while
next irq is already pending) it will not de-assert the irq, untill we
de-assert its exteral source.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

PowerPC 440GRx Rainier default config.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

PowerPC 440GRx Rainier board support.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

PowerPC 440GRx Rainier DTS.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Bootwrapper code for PowerPC 440GRx Rainier board.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add the 440EPx Sequoia USB OHCI device tree entry.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch adds runtime detection of the 440SPe revision A chips. These
chips are equipped with a slighly different PCIe core and need special/
different initialization. The compatible node is changed to
"plb-pciex-440spe" ("A" and "B" dropped). This is needed for boards that
can be equipped with both PPC revisions like the AMCC Yucca.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This makes 4xx embedded platforms re-assign all PCI resources as we
pretty much never care about what the various firmwares have done on
these, it's generally not compatible with the way the kernel will map
the bridges.

We still need to also enable bus renumbering on some of them, but I
will do that from a separate patch after I've fixed 4xx PCIe to handle
all bus numbers.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This improves the way the 4xx PCI-E code handles checking for a link
and adds explicit testing of CRS result codes on config space accesses.

This should make it more reliable.

Also, bridges with no link are now still created, though config space
accesses beyond the root complex are filtered. This is one step toward
eventually supporting hotplug.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This removes a bogus empty "ranges" property in the EBC device node
of the Bamboo board device-tree.

The "ranges" property should be created by the wrapper code when it is
implemented.  Until then, remove the empty property since it incorrectly
implies that there is a 1:1 address mapping between the EBC and the OPB.

This also fixes a warning from newer DTCs.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds base support for the Katmai board, including PCI-X and
PCI-Express (but no RTC, nvram, etc... yet).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This reworks the boot wrapper library function that probes
the chip clocks. Better separate the base function that is
used on 440GX,SPe,EP,... from the uart fixups as those need
different device-tree path on different processors.

Also, rework the function itself based on the arch/ppc code
from Eugene Surovegin which I find more readable, and which
handles one more bypass case. Also handle the subtle difference
between 440EP/EPx and 440SPe/GX, on the former, PerClk is derived
from the PLB clock while on the later, it's derived from the OPB.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds macros to the boot wrapper to access the CPR
registers from the boot wrappers.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The 4xx bootwrapper occasionally needs to access SPR registers,
this adds mfspr/mtspr wrappers to it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>