Exit traces are a lot easier to read when you don't have to remember
cryptic numbers for guest exit reasons. Symbolify them in our trace
output.
Signed-off-by: NAlexander Graf <agraf@suse.de>

Without trace points, debugging what exactly is going on inside guest
code can be very tricky. Add a few more trace points at places that
hopefully tell us more when things go wrong.
Signed-off-by: NAlexander Graf <agraf@suse.de>

We want to have tracing information on guest exits for booke as well
as book3s. Since most information is identical, use a common trace point.
Signed-off-by: NAlexander Graf <agraf@suse.de>

This patch convert different functions to take virtual page number
instead of virtual address. Virtual page number is virtual address
shifted right by VPN_SHIFT (12) bits. This enable us to have an
address range of upto 76 bits.
Reviewed-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The existing kvm_stlb_write/kvm_gtlb_write were a poor match for
the e500/book3e MMU -- mas1 was passed as "tid", mas2 was limited
to "unsigned int" which will be a problem on 64-bit, mas3/7 got
split up rather than treated as a single 64-bit word, etc.
Signed-off-by: NLiu Yu <yu.liu@freescale.com>
[scottwood@freescale.com: made mas2 64-bit, and added mas8 init]
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When running the 64-bit Book3s PR code without CONFIG_PREEMPT_NONE, we were
doing a few things wrong, most notably access to PACA fields without making
sure that the pointers stay stable accross the access (preempt_disable()).

This patch moves to_svcpu towards a get/put model which allows us to disable
preemption while accessing the shadow vcpu fields in the PACA. That way we
can run preemptible and everyone's happy!
Reported-by: NJörg Sommer <joerg@alea.gnuu.de>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This adds support for KVM running on 64-bit Book 3S processors,
specifically POWER7, in hypervisor mode.  Using hypervisor mode means
that the guest can use the processor's supervisor mode.  That means
that the guest can execute privileged instructions and access privileged
registers itself without trapping to the host.  This gives excellent
performance, but does mean that KVM cannot emulate a processor
architecture other than the one that the hardware implements.

This code assumes that the guest is running paravirtualized using the
PAPR (Power Architecture Platform Requirements) interface, which is the
interface that IBM's PowerVM hypervisor uses.  That means that existing
Linux distributions that run on IBM pSeries machines will also run
under KVM without modification.  In order to communicate the PAPR
hypercalls to qemu, this adds a new KVM_EXIT_PAPR_HCALL exit code
to include/linux/kvm.h.

Currently the choice between book3s_hv support and book3s_pr support
(i.e. the existing code, which runs the guest in user mode) has to be
made at kernel configuration time, so a given kernel binary can only
do one or the other.

This new book3s_hv code doesn't support MMIO emulation at present.
Since we are running paravirtualized guests, this isn't a serious
restriction.

With the guest running in supervisor mode, most exceptions go straight
to the guest.  We will never get data or instruction storage or segment
interrupts, alignment interrupts, decrementer interrupts, program
interrupts, single-step interrupts, etc., coming to the hypervisor from
the guest.  Therefore this introduces a new KVMTEST_NONHV macro for the
exception entry path so that we don't have to do the KVM test on entry
to those exception handlers.

We do however get hypervisor decrementer, hypervisor data storage,
hypervisor instruction storage, and hypervisor emulation assist
interrupts, so we have to handle those.

In hypervisor mode, real-mode accesses can access all of RAM, not just
a limited amount.  Therefore we put all the guest state in the vcpu.arch
and use the shadow_vcpu in the PACA only for temporary scratch space.
We allocate the vcpu with kzalloc rather than vzalloc, and we don't use
anything in the kvmppc_vcpu_book3s struct, so we don't allocate it.
We don't have a shared page with the guest, but we still need a
kvm_vcpu_arch_shared struct to store the values of various registers,
so we include one in the vcpu_arch struct.

The POWER7 processor has a restriction that all threads in a core have
to be in the same partition.  MMU-on kernel code counts as a partition
(partition 0), so we have to do a partition switch on every entry to and
exit from the guest.  At present we require the host and guest to run
in single-thread mode because of this hardware restriction.

This code allocates a hashed page table for the guest and initializes
it with HPTEs for the guest's Virtual Real Memory Area (VRMA).  We
require that the guest memory is allocated using 16MB huge pages, in
order to simplify the low-level memory management.  This also means that
we can get away without tracking paging activity in the host for now,
since huge pages can't be paged or swapped.

This also adds a few new exports needed by the book3s_hv code.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This moves the slb field, which represents the state of the emulated
SLB, from the kvmppc_vcpu_book3s struct to the kvm_vcpu_arch, and the
hpte_hash_[v]pte[_long] fields from kvm_vcpu_arch to kvmppc_vcpu_book3s.
This is in accord with the principle that the kvm_vcpu_arch struct
represents the state of the emulated CPU, and the kvmppc_vcpu_book3s
struct holds the auxiliary data structures used in the emulation.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This patch moves debugging printks for shadow SLB debugging over to tracepoints.
Signed-off-by: NAlexander Graf <agraf@suse.de>

The different ways of flusing shadow ptes have their own debug prints which use
stupid old printk.

Let's move them to tracepoints, making them easier available, faster and
possible to activate on demand
Signed-off-by: NAlexander Graf <agraf@suse.de>

This patch moves the SPTE flush debug printk over to tracepoints.
Signed-off-by: NAlexander Graf <agraf@suse.de>

This patch moves the generic mmu map debugging over to tracepoints.
Signed-off-by: NAlexander Graf <agraf@suse.de>

This patch moves Book3s MMU debugging over to tracepoints.
Signed-off-by: NAlexander Graf <agraf@suse.de>

We have a debug printk on every exit that is usually #ifdef'ed out. Using
tracepoints makes a lot more sense here though, as they can be dynamically
enabled.

This patch converts the most commonly used debug printks of EXIT_DEBUG to
tracepoints.
Signed-off-by: NAlexander Graf <agraf@suse.de>

It looks like the variable "pc" is defined. At least the current code always
failed on me stating that "pc" is already defined somewhere else.

Let's use _pc instead, because that doesn't collide.

Is this the right approach? Does it break on 440 too? If not, why not?
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

[avi: make it build]
[avi: fold trace-arch.h into trace.h]

CC: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>