The "KT" serial port has another use case for a "received break" quirk,
so before adding another special case to the 8250 core take this
opportunity to push such quirks out of the core and into a uart_port op.

Stephen says:
"If the callback function is to no longer live in 8250.c itself,
 arch/arm/mach-tegra/devices.c isn't logically a good place to put it,
 and that file will be going away once we get rid of all the board files
 and move solely to device tree."

...so since 8250_pci.c houses all the quirks for pci serial devices this
quirk is similarly housed in of_serial.c.  Once the open firmware
conversion completes the infrastructure details
(include/linux/of_serial.h, and the export) can all be removed to make
this self contained to of_serial.c.

Cc: Nhan H Mai <nhan.h.mai@intel.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
[stephen: kill CONFIG_SERIAL_TEGRA in favor just using CONFIG_ARCH_TEGRA]
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSudhakar Mamillapalli <sudhakar@fb.com>
Reported-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the errata is populated based on cpu checks this can
be removed and replaced with module version check of uart ip block.
MVR reg is provided within the uart reg map use the same
to populate the errata and thus now errata population and handling
can be managed within the driver itself.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Reviewed-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Problem Observed:
- interrupt status is set by rising or falling edge on CTS line
- interrupt status is cleared on a .0. to .1. transition of the
  interrupt-clear register bit 1.
- interrupt-clear register is reset by hardware once the interrupt
  status is .0..
  Remark: It seems not possible to read this register back by the
  CPU though, but internally this register exists.
- when simultaneous set and reset event on the interrupt status
  happens, then the set-event has priority and the status remains
  .1.. As a result the interrupt-clear register is not reset to
  .0., and no new .0. to .1. transition can be detected on it when
  writing a .1. to it.
  This implies race condition, the clear must be performed at least
  one UARTCLK the riding edge of CTS RIS interrupt.

Fix:
  Instead of resetting UART as done in commit
  c16d51a3
  "amba pl011: workaround for uart registers lockup" do the
  following:

  write .0. and then  .1. to the interrupt-clear register to make
  sure that this transition is detected. According to the datasheet
  writing a .0. does not have any effect, but actually it allows to
  reset the internal interrupt-clear register.

  Take into account:
  The .0. needs to last at least for one clk_uart clock period
  (~ 38 MHz, 26.08ns)

This way we can do away with the tasklet and keep only a tiny
fix triggered by the variant flag introduced in this patch.
Signed-off-by: NGuillaume Jaunet <guillaume.jaunet@stericsson.com>
Signed-off-by: NChristophe Arnal <christophe.arnal@stericsson.com>
Signed-off-by: NMatthias Locher  <Matthias.Locher@stericsson.com>
Signed-off-by: NRajanikanth H.V <rajanikanth.hv@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix compile error caused by "TTY: con3215, use tty from tty_port":

 CC      drivers/s390/char/con3215.o
drivers/s390/char/con3215.c: In function 'raw3215_wakeup':
drivers/s390/char/con3215.c:339:16: error: 'struct raw3215_info' has no member named 'tty'
make[1]: *** [drivers/s390/char/con3215.o] Error 1
make: *** [drivers/s390/char/] Error 2

Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 26f41062 ("PCI: check for pci bar restore completion and
retry") attempted to address problems with PCI BAR restoration on
systems where FLR had not been completed before pci_restore_state() was
called, but it did that in an utterly wrong way.

First off, instead of retrying the writes for the BAR registers only, it
did that for all of the PCI config space of the device, including the
status register (whose value after the write quite obviously need not be
the same as the written one).  Second, it added arbitrary delay to
pci_restore_state() even for systems where the PCI config space
restoration was successful at first attempt.  Finally, the mdelay(10) it
added to every iteration of the writing loop was way too much of a delay
for any reasonable device.

All of this actually caused resume failures for some devices on Mikko's
system.

To fix the regression, make pci_restore_state() only retry the writes
for BAR registers and only wait if the first read from the register
doesn't return the written value.  Additionaly, make it wait for 1 ms,
instead of 10 ms, after every failing attempt to write into config
space.
Reported-by: NMikko Vinni <mmvinni@yahoo.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 18a4d0a2 ("[SCSI] Handle disk devices which can not process
medium access commands") introduced a bug in which we would attempt to
dereference the scsi driver even when the device had no ULD attached.

Ensure that a driver is registered and make the driver accessor function
more resilient to errors during device discovery.
Reported-by: NElric Fu <elricfu1@gmail.com>
Reported-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The OMAP driver needs a 'depends on ARCH_OMAP2PLUS' since it only
builds for OMAP2+ platforms.

This 'depends on' was in the original patch from Russell King, but was
erroneously removed by me when making this option user-selectable in
commit b09db45c (cpufreq: OMAP driver depends CPUfreq tables.)  This
patch remedies that.

Apologies to Russell King for breaking his originally working patch.

Also, thanks to Grazvydas Ignotas for reporting the same problem.

Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Obtain tty_struct only once in ISR and pass it down to
raw3215_next_io. Other than that, we just use the tty with raised
reference. And set it properly in open and close.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

And use flags from that. But first we have to get rid of duplicated
flag names. From now on, for the standard ones that are stored in
tty_port->flags, we use ASYNC_* ones.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A -next commit "TTY: HVC, use tty from tty_port" switched the driver
to use tty_port helper for tty refcounting. But it omitted to remove
manual tty refcounting from open, close and hangup. So now we are
getting random crashes caused by use-after-free:
Unable to handle kernel paging request for data at address 0xc0000003f9d550
Faulting instruction address: 0xc0000000001b7f40
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP: c0000000001b7f40 LR: c0000000001b7f14 CTR: c0000000000e04f0
...
NIP [c0000000001b7f40] .__kmalloc+0x70/0x230
LR [c0000000001b7f14] .__kmalloc+0x44/0x230
Call Trace:
[c0000003f68bf930] [c0000003f68bf9b0] 0xc0000003f68bf9b0 (unreliable)
[c0000003f68bf9e0] [c0000000001e5424] .alloc_fdmem+0x24/0x70
[c0000003f68bfa60] [c0000000001e54f8] .alloc_fdtable+0x88/0x130
[c0000003f68bfaf0] [c0000000001e5924] .dup_fd+0x384/0x450
[c0000003f68bfbd0] [c00000000009a310] .copy_process+0x880/0x11d0
[c0000003f68bfcd0] [c00000000009aee0] .do_fork+0x70/0x400
[c0000003f68bfdc0] [c0000000000141c4] .sys_clone+0x54/0x70
[c0000003f68bfe30] [c000000000009aa0] .ppc_clone+0x8/0xc

Fix that by complete removal of tty_kref_get/put in open/close/hangup
paths.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Reported-and-tested-by: NMichael Neuling <mikey@neuling.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: ppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The change
    commit 461cbe77
    Author: Gregory Bean <gbean@codeaurora.org>
    Date:   Wed Jul 28 10:22:13 2010 -0700

        video: msm: Fix section mismatch in mddi.c.

fixes a section mismatch between the board file and the driver's probe
function, however, it misses the additional mismatches between the
probe function and some routines it calls.  Fix these up as well.
Signed-off-by: NDavid Brown <davidb@codeaurora.org>

The AMBA bus regulator support is being used to model on/off switches
for power domains which isn't terribly idiomatic for modern kernels with
the generic power domain code and creates integration problems on platforms
which don't use regulators for their power domains as it's hard to tell
the difference between a regulator that is needed but failed to be provided
and one that isn't supposed to be there (though DT does make that easier).

Platforms that wish to use the regulator API to manage their power domains
can indirect via the power domain interface.

This feature is only used with the vape supply of the db8500 PRCMU
driver which supplies the UARTs and MMC controllers, none of which have
support for managing vcore at runtime in mainline (only pl022 SPI
controller does).  Update that supply to have an always_on constraint
until the power domain support for the system is updated so that it is
enabled for these users, this is likely to have no impact on practical
systems as probably at least one of these devices will be active and
cause AMBA to hold the supply on anyway.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If, in __persistent_ram_init(), the call to
persistent_ram_buffer_init() fails or the call to
persistent_ram_init_ecc() fails then we fail to free the memory we
allocated to 'prz' with kzalloc() - thus leaking it.

To prevent the leaks I consolidated all error exits from the function
at a 'err:' label at the end and made all error cases jump to that
label where we can then make sure we always free 'prz'. This is safe
since all the situations where the code bails out happen before 'prz'
has been stored anywhere and although we'll do a redundant kfree(NULL)
call in the case of kzalloc() itself failing that's OK since kfree()
deals gracefully with NULL pointers and I felt it was more important
to keep all error exits at a single location than to avoid that one
harmless/redundant kfree() on a error path.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NColin Cross <ccross@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If copy_to_user() fails in the WLAN_CMD_GET_NODE_LIST case of the
switch in drivers/staging/vt6656/ioctl.c::private_ioctl() we'll leak
the memory allocated to 'pNodeList'. Fix that by kfree'ing the memory
in the failure case.
Also remove a pointless cast (to type 'PSNodeList') of a kmalloc()
return value - kmalloc() returns a void pointer that is implicitly
converted, so there is no need for an explicit cast.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix crash after issuing:
	echo hmc5843 0x1e > /sys/class/i2c-dev/i2c-2/device/new_device

	[   37.180999] device: '2-001e': device_add
	[   37.188293] bus: 'i2c': add device 2-001e
	[   37.194549] PM: Adding info for i2c:2-001e
	[   37.200958] bus: 'i2c': driver_probe_device: matched device 2-001e with driver hmc5843
	[   37.210815] bus: 'i2c': really_probe: probing driver hmc5843 with device 2-001e
	[   37.224884] HMC5843 initialized
	[   37.228759] ------------[ cut here ]------------
	[   37.233612] kernel BUG at mm/slab.c:505!
	[   37.237701] Internal error: Oops - BUG: 0 [#1] PREEMPT
	[   37.243103] Modules linked in:
	[   37.246337] CPU: 0    Not tainted  (3.3.1-gta04+ #28)
	[   37.251647] PC is at kfree+0x84/0x144
	[   37.255493] LR is at kfree+0x20/0x144
	[   37.259338] pc : [<c00b408c>]    lr : [<c00b4028>]    psr: 40000093
	[   37.259368] sp : de249cd8  ip : 0000000c  fp : 00000090
	[   37.271362] r10: 0000000a  r9 : de229eac  r8 : c0236274
	[   37.276855] r7 : c09d6490  r6 : a0000013  r5 : de229c00  r4 : de229c10
	[   37.283691] r3 : c0f00218  r2 : 00000400  r1 : c0eea000  r0 : c00b4028
	[   37.290527] Flags: nZcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
	[   37.298095] Control: 10c5387d  Table: 9e1d0019  DAC: 00000015
	[   37.304107] Process sh (pid: 91, stack limit = 0xde2482f0)
	[   37.309844] Stack: (0xde249cd8 to 0xde24a000)
	[   37.314422] 9cc0:                                                       de229c10 de229c00
	[   37.322998] 9ce0: de229c10 ffffffea 00000005 c0236274 de140a80 c00b4798 dec00080 de140a80
	[   37.331573] 9d00: c032f37c dec00080 000080d0 00000001 de229c00 de229c10 c048d578 00000005
	[   37.340148] 9d20: de229eac 0000000a 00000090 c032fa40 00000001 00000000 00000001 de229c10
	[   37.348724] 9d40: de229eac 00000029 c075b558 00000001 00000003 00000004 de229c10 c048d594
	[   37.357299] 9d60: 00000000 60000013 00000018 205b0007 37332020 3432322e 5d343838 c0060020
	[   37.365905] 9d80: de251600 00000001 00000000 de251600 00000001 c0065a84 de229c00 de229c48
	[   37.374481] 9da0: 00000006 0048d62c de229c38 de229c00 de229c00 de1f6c00 de1f6c20 00000001
	[   37.383056] 9dc0: 00000000 c048d62c 00000000 de229c00 de229c00 de1f6c00 de1f6c20 00000001
	[   37.391632] 9de0: 00000000 c048d62c 00000000 c0330164 00000000 de1f6c20 c048d62c de1f6c00
	[   37.400207] 9e00: c0330078 de1f6c04 c078d714 de189b58 00000000 c02ccfd8 de1f6c20 c0795f40
	[   37.408782] 9e20: c0238330 00000000 00000000 c02381a8 de1b9fc0 de1f6c20 de1f6c20 de249e48
	[   37.417358] 9e40: c0238330 c0236bb0 decdbed8 de7d0f14 de1f6c20 de1f6c20 de1f6c54 de1f6c20
	[   37.425933] 9e60: 00000000 c0238030 de1f6c20 c078d7bc de1f6c20 c02377ec de1f6c20 de1f6c28
	[   37.434509] 9e80: dee64cb0 c0236138 c047c554 de189b58 00000000 c004b45c de1f6c20 de1f6cd8
	[   37.443084] 9ea0: c0edfa6c de1f6c00 dee64c68 de1f6c04 de1f6c20 dee64cb8 c047c554 de189b58
	[   37.451690] 9ec0: 00000000 c02cd634 dee64c68 de249ef4 de23b008 dee64cb0 0000000d de23b000
	[   37.460266] 9ee0: de23b007 c02cd78c 00000002 00000000 00000000 35636d68 00333438 00000000
	[   37.468841] 9f00: 00000000 00000000 001e0000 00000000 00000000 00000000 00000000 0a10cec0
	[   37.477416] 9f20: 00000002 de249f80 0000000d dee62990 de189b40 c0234d88 0000000d c010c354
	[   37.485992] 9f40: 0000000d de210f28 000acc88 de249f80 0000000d de248000 00000000 c00b7bf8
	[   37.494567] 9f60: de210f28 000acc88 de210f28 000acc88 00000000 00000000 0000000d c00b7ed8
	[   37.503143] 9f80: 00000000 00000000 0000000d 00000000 0007fa28 0000000d 000acc88 00000004
	[   37.511718] 9fa0: c000e544 c000e380 0007fa28 0000000d 00000001 000acc88 0000000d 00000000
	[   37.520294] 9fc0: 0007fa28 0000000d 000acc88 00000004 00000001 00000020 00000002 00000000
	[   37.528869] 9fe0: 00000000 beab8624 0000ea05 b6eaebac 600d0010 00000001 00000000 00000000
	[   37.537475] [<c00b408c>] (kfree+0x84/0x144) from [<c0236274>] (device_add+0x530/0x57c)
	[   37.545806] [<c0236274>] (device_add+0x530/0x57c) from [<c032fa40>] (iio_device_register+0x8c8/0x990)
	[   37.555480] [<c032fa40>] (iio_device_register+0x8c8/0x990) from [<c0330164>] (hmc5843_probe+0xec/0x114)
	[   37.565338] [<c0330164>] (hmc5843_probe+0xec/0x114) from [<c02ccfd8>] (i2c_device_probe+0xc4/0xf8)
	[   37.574737] [<c02ccfd8>] (i2c_device_probe+0xc4/0xf8) from [<c02381a8>] (driver_probe_device+0x118/0x218)
	[   37.584777] [<c02381a8>] (driver_probe_device+0x118/0x218) from [<c0236bb0>] (bus_for_each_drv+0x4c/0x84)
	[   37.594818] [<c0236bb0>] (bus_for_each_drv+0x4c/0x84) from [<c0238030>] (device_attach+0x78/0xa4)
	[   37.604125] [<c0238030>] (device_attach+0x78/0xa4) from [<c02377ec>] (bus_probe_device+0x28/0x9c)
	[   37.613433] [<c02377ec>] (bus_probe_device+0x28/0x9c) from [<c0236138>] (device_add+0x3f4/0x57c)
	[   37.622650] [<c0236138>] (device_add+0x3f4/0x57c) from [<c02cd634>] (i2c_new_device+0xf8/0x19c)
	[   37.631805] [<c02cd634>] (i2c_new_device+0xf8/0x19c) from [<c02cd78c>] (i2c_sysfs_new_device+0xb4/0x130)
	[   37.641754] [<c02cd78c>] (i2c_sysfs_new_device+0xb4/0x130) from [<c0234d88>] (dev_attr_store+0x18/0x24)
	[   37.651611] [<c0234d88>] (dev_attr_store+0x18/0x24) from [<c010c354>] (sysfs_write_file+0x10c/0x140)
	[   37.661193] [<c010c354>] (sysfs_write_file+0x10c/0x140) from [<c00b7bf8>] (vfs_write+0xb0/0x178)
	[   37.670410] [<c00b7bf8>] (vfs_write+0xb0/0x178) from [<c00b7ed8>] (sys_write+0x3c/0x68)
	[   37.678833] [<c00b7ed8>] (sys_write+0x3c/0x68) from [<c000e380>] (ret_fast_syscall+0x0/0x3c)
	[   37.687683] Code: 1593301c e5932000 e3120080 1a000000 (e7f001f2)
	[   37.700775] ---[ end trace aaf805debdb69390 ]---

Client data was assigned to iio_dev structure in probe but in
hmc5843_init_client function casted to private driver data structure which
is wrong. Possibly calling mutex_init(&data->lock); corrupt data
which the lead to above crash.
Signed-off-by: NMarek Belisko <marek.belisko@open-nandra.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The ST variants of the PL031 all require bit 26 in the control register
to be set before they work properly.  Discovered this when testing on
the Nomadik board where it would suprisingly just stand still.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

RTC stores time and date in several registers.  Due to the fact that
these registers can't be read instantaneously, there is a chance that
reading from counting registers gives an error of one minute, one hour,
one day, etc.

To address this issue, the RTC has hardware support to copy the RTC
counting registers to static shadowed registers.  The current
implementation does not use this feature, and in a stress test, we can
reproduce this error at a rate of around two times per 300000 readings.

Fix the implementation to ensure that the right snapshot of time is
captured.
Signed-off-by: NKonstantin Shlyakhovoy <x0155534@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: linux-omap <linux-omap@vger.kernel.org>
Acked-by: NMykola Oleksiienko <x0174904@ti.com>
Acked-by: NOleksandr Dmytryshyn <oleksandr.dmytryshyn@ti.com>
Acked-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Driver data field is a pointer, hence assigning that to an integer results
in compilation warnings.

Fixes following compilation warnings:

  drivers/rtc/rtc-s3c.c: In function `s3c_rtc_get_driver_data':
  drivers/rtc/rtc-s3c.c:452:3: warning: return makes integer from pointer without a cast [enabled by default]
  drivers/rtc/rtc-s3c.c: At top level:
  drivers/rtc/rtc-s3c.c:674:3: warning: initialization makes pointer from integer without a cast [enabled by default]
  drivers/rtc/rtc-s3c.c:674:3: warning: (near initialization for `s3c_rtc_dt_match[1].data') [enabled by default]
  drivers/rtc/rtc-s3c.c:677:3: warning: initialization makes pointer from integer without a cast [enabled by default]
  drivers/rtc/rtc-s3c.c:677:3: warning: (near initialization for `s3c_rtc_dt_match[2].data') [enabled by default]
  drivers/rtc/rtc-s3c.c:680:3: warning: initialization makes pointer from integer without a cast [enabled by default]
  drivers/rtc/rtc-s3c.c:680:3: warning: (near initialization for `s3c_rtc_dt_match[3].data') [enabled by default]
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix this error:

  drivers/rtc/rtc-s3c.c: At top level:
  drivers/rtc/rtc-s3c.c:671:3: error: request for member `data' in something not a structure or union
  drivers/rtc/rtc-s3c.c:674:3: error: request for member `data' in something not a structure or union
  drivers/rtc/rtc-s3c.c:677:3: error: request for member `data' in something not a structure or union
  drivers/rtc/rtc-s3c.c:680:3: error: request for member `data' in something not a structure or union
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

efi_rtc_init() uses platform_driver_probe(), so there's no need to also
set efi_rtc_driver's probe member (as it won't be used anyway).  This
fixes a modpost section mismatch warning (as efi_rtc_probe() validly is
__init).
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

hwclock refuses to set date/time if RTC registers contain invalid
values.  Check the date/time register values at probe time and
initialize them to make hwclock happy.
Signed-off-by: NAndreas Dumberger <andreas.dumberger@tqs.de>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

/proc/sys/kernel/random/boot_id can be read concurrently by userspace
processes.  If two (or more) user-space processes concurrently read
boot_id when sysctl_bootid is not yet assigned, a race can occur making
boot_id differ between the reads.  Because the whole point of the boot id
is to be unique across a kernel execution, fix this by protecting this
operation with a spinlock.

Given that this operation is not frequently used, hitting the spinlock
on each call should not be an issue.
Signed-off-by: NMathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since commit 96104eda ("RDMA/core: Add SRQ type field"), kernel
users of SRQs need to specify srq_type = IB_SRQT_BASIC in struct
ib_srq_init_attr, or else most low-level drivers will fail in
when srpt_add_one() calls ib_create_srq() and gets -ENOSYS.

(mlx4_ib works OK nearly all of the time, because it just needs
srq_type != IB_SRQT_XRC.  And apparently nearly everyone using
ib_srpt is using mlx4 hardware)
Reported-by: NAlexey Shvetsov <alexxy@gentoo.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This fixes a resume regression introduced in

commit 7dd49065
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Wed Mar 21 10:48:18 2012 +0000

    drm/i915: Mark untiled BLT commands as fenced on gen2/3

which fixed fencing tracking for untiled blt commands.

A side effect of that patch was that now also untiled objects have a
non-zero obj->last_fenced_seqno to track when a fence can be set up
after a pipelined tiling change. Unfortunately this was only cleared
by the fence setup and teardown code, resulting in tons of untiled but
inactive objects with non-zero last_fenced_seqno.

Now after resume we completely reset the seqno tracking, both on the
driver side (by setting dev_priv->next_seqno = 1) and on the hw side
(by allocating a new hws page, which contains the seqnos). Hilarity
and indefinite waits ensued from the stale seqnos in
obj->last_fenced_seqno from before the suspend.

The fix is to properly clear the fencing tracking state like we
already do for the normal gpu rendering while moving objects off the
active list.
Reported-and-tested-by: N"Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This removes the HOTPLUG_PCI_PCIE dependency on the driver and makes it
depend on PCI.

Cc: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

If a bitmap is added while the array is active, it is possible
for bitmap_daemon_work to run while the bitmap is being
initialised.
This is particularly a problem if bitmap_daemon_work sees
bitmap->filemap as non-NULL before it has been filled in properly.
So hold bitmap_info.mutex while filling in ->filemap
to prevent problems.

This patch is suitable for any -stable kernel, though it might not
apply cleanly before about 3.1.

Cc: stable@vger.kernel.org
Signed-off-by: NNeilBrown <neilb@suse.de>

If r1bio->sectors % 8 != 0,then the memcmp and a later
memcpy will omit the last bio_vec.

This is suitable for any stable kernel since 3.1 when bad-block
management was introduced.

Cc: stable@vger.kernel.org
Signed-off-by: Nmajianpeng <majianpeng@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

bitmap_new_disk_sb() would still create V3 bitmap superblock
with host-endian layout.

Perhaps I'm confused, but shouldn't bitmap_new_disk_sb() be
creating a V4 bitmap superblock instead, that is portable,
as per comment in bitmap.h?
Signed-off-by: NAndrei Warkentin <andrey.warkentin@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

The struct exynos_drm_manager has to exist for exynos drm sub driver
using encoder and connector. If it isn't NULL to member of struct
exynos_drm_subdrv, will create encoder and connector else will not. And
the is_local member also doesn't need.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The mixer driver and hdmi driver have each operation callback functions
and they is registered to hdmi common driver. Their struct names in hdmi
common driver include display, manager and overlay. It confuses to
appear whose operation and two driver cannot register same operation
callback functions at the same time. Use their struct names to driver
name.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The default_win member in struct mixer_context isn't change its value
after initialized to 0, so it's better using to define.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

HDMI_OVERLAY_NUMBER is specific of mixer driver and be used "windows
layer" term in exynos user manaual, so rename it.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Some members in struct mixer_context aren't used and the define
HDMI_OVERLAY_NUMBER is unused in hdmi driver, remove them.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

When the void pointer type variable is assigned to the specific pointer
type variable, don't need to do type conversion.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

If, in drivers/input/misc/da9052_onkey.c::da9052_onkey_probe(), the
call to either kzalloc() or input_allocate_device() fails then we will
return -ENOMEM from the function without freeing the other allocation
that may have succeeded, thus we leak either the memory allocated for
'onkey' or the memory allocated for 'input_dev' if one succeeds and
the other fails.
Fix that by jumping to the 'err_free_mem' label at the end of the
function that properly cleans up rather than returning directly.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This reverts commit b5195082.

The reason for this revert is that making the frequency verification
preemptible and interruptible is not working reliably. Michaels
machine failed to use PM-timer with the message:

  PM-Timer running at invalid rate: 113% of normal - aborting.

That's not a surprise as the frequency verification does rely on
interrupts being disabled. With a async scheduled thread there is no
guarantee to achieve the same result. Also some driver might fiddle
with the CTC channel 2 during the verification period, which makes the
result even more random and unpredictable.

This can be solved by using the same mechanism as we use in the
deferred TSC validation code, but that only will work if we verified a
working HPET _BEFORE_ trying to do the PM-Timer lazy validation.

So for now reverting is the safe option.
Bisected-by: NMichael Witten <mfwitten@gmail.com>
Cc: Arjan van de Ven <arjanvandeven@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <alpine.LFD.2.02.1204112303270.2542@ionos>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

People have been getting confused and thinking this is a runtime control.

Cc: stable@vger.kernel.org
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In https://bugzilla.kernel.org/show_bug.cgi?id=42976, a system with driver
rtl8192se used as an AP suffers from "Out of SW-IOMMU space" errors. These
are caused by the DMA buffers used for beacons never being unmapped.

This bug was also reported at
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/961618Reported-and-Tested-by: NDa Xue <da@lessconfused.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current version of rtlwifi for USB operations uses kmalloc to
acquire a 32-bit buffer for each read of the device. When
_usb_read_sync() is called with the rcu_lock held, the result is
a "sleeping function called from invalid context" BUG. This is
reported for two cases in https://bugzilla.kernel.org/show_bug.cgi?id=42775.
The first case has the lock originating from within rtlwifi and could
be fixed by rearranging the locking; however, the second originates from
within mac80211. The kmalloc() call is removed from _usb_read_sync()
by creating a ring buffer pointer in the private area and
allocating the buffer data in the probe routine.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [This version good for 3.3+ - different patch for 3.2 - 2.6.39]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Re-define XHCI_LEGACY_DISABLE_SMI and used it in right way. All SMI enable
bits will be cleared to zero and flag bits 29:31 are also cleared to zero.
Other bits should be presvered as Table 146.

This patch should be backported to kernels as old as 2.6.31.
Signed-off-by: NAlex He <alex.he@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org