When handling IWM_CMD_PMKID_FLUSH command, the bssid and
pmkid in pmksa are all NULL. Check it before memcpy.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

An earlier optimization on removing unnecessary traffic on cooked
monitor interfaces ("mac80211: reduce the amount of unnecessary traffic
on cooked monitor interfaces ") ended up removing quite a bit more
than just unnecessary traffic. It was not supposed to remove TX status
reporting for injected frames, but ended up doing it by checking the
injected flag in skb->cb only after that field had been cleared with
memset.. Fix this by taking a local copy of the injected flag before
skb->cb is cleared.

This broke user space applications that depend on getting TX status
notifications for injected data frames. For example, STA inactivity
poll from hostapd did not work and ended up kicking out stations even
if they were still present.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, the 2GHz band is enabled unconditionally, even if the device
does not support it.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On BigEndian gcc complains:

drivers/net/wireless/airo.c: In function ‘sniffing_mode’:
drivers/net/wireless/airo.c:4809: warning: integer overflow in expression

Fix this by doing the bitwise AND on the host-endian value.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While reviewing the l2pad function to align both the header and the payload
on a DMA-capable boundary a bug was discovered where the payload would not
be properly aligned. The header_align value was used where the payload_align
value should have been used.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I've just noticed that some events are no longer propagated
for some wireless drivers. Basically, SET request with a extra payload
for driver without commit handler. The fix is pretty simple, see
attached.
	Actually, a few lines below this line, you will see that the
event generation for simple SET (iwpoint-less ?) is done properly,
and this other event generation does not need fixing.
Signed-off-by: NJean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For PPC architecture with PHY Revision < 3, a read of the register
B43_MMIO_HWENABLED_LO will cause a CPU fault unless b43legacy_status()
returns a value of 2 (B43legacy_STAT_STARTED); however, one finds that
the driver is unable to associate after resuming from hibernation unless
this routine returns 1. To satisfy both conditions, the routine is rewritten
to return TRUE whenever b43legacy_status() returns a value < 2.

This patch fixes the second problem listed in the postings for Red Hat
Bugzilla #538523.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The routine b43_is_hw_radio_enabled() has long been a problem.
For PPC architecture with PHY Revision < 3, a read of the register
B43_MMIO_HWENABLED_LO will cause a CPU fault unless b43_status()
returns a value of 2 (B43_STAT_STARTED) (BUG 14181). Fixing that
results in Bug 14538 in which the driver is unable to reassociate
after resuming from hibernation because b43_status() returns 0.

The correct fix would be to determine why the status is 0; however,
I have not yet found why that happens. The correct value is found for
my device, which has PHY revision >= 3.

Returning TRUE when the PHY revision < 3 and b43_status() returns 0 fixes
the regression for 2.6.32.

This patch fixes the problem in Red Hat Bugzilla #538523.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NChristian Casteyde <casteyde.christian@free.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need to implement the PMKSA API for proper WPA2 pre-auth and fast
re-association. Our fullmac device generates all (re-)assoc IEs, and thus it
needs the right PMKIDs. With this implementation we now get them from
wpa_supplicant.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the addition of the *_pmksa cfg80211 ops, we can now add the
corresponding wireless extensions compatibility handler.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is an interface to set, delete and flush PMKIDs through nl80211.
Main users would be fullmac devices which firmwares are capable of
generating the RSN IEs for the re-association requests, e.g. iwmc3200wifi.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In my setups, ath9k's debugfs files are most of the time much more
useful than the messages generated by enabling CONFIG_ATH_DEBUG along
with the right debug flags.
Since CONFIG_ATH_DEBUG comes with a noticeable overhead on embedded
systems, this patch makes it possible to use the debugfs files without
that option.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable logging of more configuration data when tracing
is enabled. Except for the channel frequency this is
only useful with the binary trace format, but that can
be recorded and replayed with trace-cmd and I will be
working on a plugin that reports all the information.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As indicated by the comment, the aMPDU RX reorder code
should logically be after ieee80211_rx_h_check(). The
previous patch moved the code there, and this patch now
hooks it up in that place by introducing a list of skbs
that are then processed by the remaining handlers. The
list may be empty if the function is buffering the skb
to release it later.

The only change needed to the RX data is that the crypto
handler needs to clear the key that may be set from a
previous loop iteration, and that not everything can be
in the rx flags now.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This code should be part of RX handlers, so move it
to the place where it belongs without changing it.
A follow-up patch will do the changes to hook it up.
The sole purpose of this code move is to make the
other patch readable, it doesn't change the code at
all except that it now requires a different static
function declaration (which will go away too).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The RX flags should soon be used only for flags
that cannot change within an a-MPDU, so move the
cooked monitor flag into the RX status flags.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves the works cleanup, scan and events to a cfg80211
dedicated workqueue.

Platform driver like eeepc-laptop ought to use works to rfkill (as
new rfkill does lock in rfkill_unregister and the platform driver is
called from rfkill_switch_all which also lock the same mutex).
This raise a new issue in itself that the work scheduled by the platform
driver to the global worqueue calls wiphy_unregister which flush_work
scan and event works (which thus flush works on the global workqueue inside
a work on the global workqueue) and also put on hold the  wdev_cleanup_work
 (which prevents the dev_put on netdev thus indefinite Usage count error on
wifi device).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAlban Browaeys <prahal@yahoo.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHolger Schurig <holgerschurig@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHolger Schurig <holgerschurig@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This moves mesh initialization, start/stop and rx/tx handling from
into mesh.c.
Signed-off-by: NHolger Schurig <holgerschurig@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHolger Schurig <holgerschurig@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mesh.c will be the file where we concentrate all mesh-related
code. This allows us to either add a KConfig entry for mesh and
makes matters easier for the cfg80211 transition.
Signed-off-by: NHolger Schurig <holgerschurig@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the beacon queue parameters with best effort queue parameters for
IBSS mode. This reduces the number of beacons generated by ath9k and
ensures a fair beacon distribution when there are multiple IBSS stations.
Also CWmin is quadrupled to achieve the expected percentage of
distribution.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Atheros single stream AR9285 and AR9271 have half the PCU TX FIFO
buffer size of that of dual stream devices. Dual stream devices
have a max PCU TX FIFO size of 8 KB while single stream devices
have 4 KB. Single stream devices have an issue though and require
hardware only to use half of the amount of its capable PCU TX FIFO
size, 2 KB and this requires a change in software.

Technically a change would not have been required (except for frame
burst considerations of 128 bytes) if these devices would have been
able to use the full 4 KB of the PCU TX FIFO size but our systems
engineers recommend 2 KB to be used only. We enforce this through
software by reducing the max frame triggger level to 2 KB.

Fixing the max frame trigger level should then have a few benefits:

  * The PER will now be adjusted as designed for underruns when the
    max trigger level is reached. This should help alleviate the
    bus as the rate control algorithm chooses a slower rate which
    should ensure frames are transmitted properly under high system
    bus load.

  * The poll we use on our TX queues should now trigger and work
    as designed for single stream devices. The hardware passes
    data from each TX queue on the PCU TX FIFO queue respecting each
    queue's priority. The new trigger level ensures this seeding of
    the PCU TX FIFO queue occurs as designed which could mean avoiding
    false resets and actually reseting hw correctly when a TX queue
    is indeed stuck.

  * Some undocumented / unsupported behaviour could have been triggered
    when the max trigger level level was being set to 4 KB on single
    stream devices. Its not clear what this issue was to me yet.

Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: Bennyam Malavazi <bennyam.malavazi@atheros.com>
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Shan Palanisamy <shan.palanisamy@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Software padding is done on the TX path and software unpadding is done on the
RX path. This patch corrects the position where the padding occurs. A specific
function computes the pad position and this function is used in the TX and RX
path. This patch has been tested by generating every possible 802.11 frames
with every possible frame_control field and a varying length. This patch is
useful for analyzing non standard 802.11 frames going over the air
Signed-off-by: NBenoit Papillault <benoit.papillault@free.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When mac80211 was telling us to go into Powersave we listened
and immediately turned RX off. This meant hardware would not
see the ACKs from the AP we're associated with and hardware
we'd end up retransmiting the null data frame in a loop
helplessly.

Fix this by keeping track of the transmitted nullfunc frames
and only when we are sure the AP has sent back an ACK do we
go ahead and shut RX off.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NVivek Natarajan <Vivek.Natarajan@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The tx concatenation option works fine now, we no longer need the debugging
option of disabling concatenation.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We add the stopped queue count and display to the tx queue debugfs entry.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To support 802.11n Tx aggregation support with iwmc3200 wifi, we have to
handle the UMAC_CMD_OPCODE_STOP_RESUME_STA_TX notification from the UMAC.
Before sending an AddBA, the UMAC synchronizes with the host in order to
know what is the last Tx frame it's supposed to receive before it will be
able to start the actual aggregation session.
We thus have to keep track of the last sequence number that is scheduled
for transmission on a particular RAxTID, send an answer to the UMAC with
this sequence number. The UMAC then does the BA negociation and once it's
done with it sends a new UMAC_CMD_OPCODE_STOP_RESUME_STA_TX notification
to let us know that we can resume the Tx flow on the specified RAxTID.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Reviewed-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set the wireless mode with regard to both the driver's configuration
and the device's EEPROM result.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The iwmc3200wifi eeprom contains information about the available PHYs on
the chip. We should update our wireless_mode setting and profile according
to it.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we're down, we shouldnt try to set the UMAC power limit. We just return 0
instead, and cfg80211 toggles the soft rfkill state.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The fat channels eeprom entries let us know if 11n is enabled or not. We
update our wiphy supported bands based on that.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update MAINTAINERS with the Intel supported iwmc3200wifi entry.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set the value of extra_tx_headroom in a central place, rather than in each
of the drivers. This is preparatory for taking alignment space into account
in the TX headroom requested by rt2x00.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean up the use of whitespace in the initialization of the rt2x00_ops
structures. This is preparatory for a later patch that adds members
to that structure, which require different whitespace alignment.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <ivdoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RT chipsets are unique across both PCI and USB busses, and don't overlap.
Therefore there is no need to test for bus type when only checking for
chipset type. Remove the redundant checks.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <ivdoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>