Add a linked list for keeping multiple PHY instances with different
types so that we can have separate USB2 and USB3 PHYs on one single
board. _get_phy_ has been changed so that the controller gets
the transceiver by type. _remove_phy_ has been added to let the phy
be removed from the phy list.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

_transceiver() in otg.c is replaced with _phy. usb_set_transceiver is
replaced with usb_add_phy to make it similar to other usb standard
function names like usb_add_hcd.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

pm_runtime_get_sync returns a signed integer. In case of errors
it returns a negative value. This patch fixes the error check
by making it signed instead of unsigned thus preventing register
access if get_sync_fails. Also passes the error cause to the
debug message.

Cc: stable@vger.kernel.org
Cc:  Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

pm_runtime_enable is being called after omap2430_musb_init. Hence
pm_runtime_get_sync in omap2430_musb_init does not have any effect (does
not enable clocks) resulting in a crash during register access. It is
fixed here.

Cc: stable@vger.kernel.org # v3.0, v3.1, v3.2, v3.3
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When runtime_pm was originally added, it was done in rather confusing
way: omap2430_musb_init() (called from musb_init_controller) would do
runtime_pm_get_sync() and musb_init_controller() itself would do
runtime_pm_put to balance it out. This is not only confusing but also
wrong if non-omap2430 glue layer is used.

This confusion resulted in commit 772aed45 "usb: musb: fix
pm_runtime mismatch", that removed runtime_pm_put() from
musb_init_controller as that looked unbalanced, and also happened to
fix unrelated isp1704_charger crash. However this broke runtime PM
functionality (musb is now always powered, even without gadget active).

Avoid these confusing runtime pm dependences by making
musb_init_controller() and omap2430_musb_init() do their own runtime
get/put pairs; also cover error paths. Remove unneeded runtime_pm_put
in omap2430_remove too. isp1704_charger crash that motivated
772aed45 will be fixed by following patch.

Cc: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This change prevents runtime suspend and resume actual execution, if
omap2430 controller driver is loaded after musb-hdrc, and therefore the
controller isn't initialized properly.

The problem is reproducible with 3.1.y and 3.2 kernels.

Kernel configuration of musb:

  % cat .config | egrep 'MUSB|GADGET'
  CONFIG_USB_MUSB_HDRC=y
  # CONFIG_USB_MUSB_TUSB6010 is not set
  CONFIG_USB_MUSB_OMAP2PLUS=m
  # CONFIG_USB_MUSB_AM35X is not set
  CONFIG_MUSB_PIO_ONLY=y
  CONFIG_USB_GADGET=y
  # CONFIG_USB_GADGET_DEBUG is not set
  # CONFIG_USB_GADGET_DEBUG_FILES is not set
  # CONFIG_USB_GADGET_DEBUG_FS is not set
  CONFIG_USB_GADGET_VBUS_DRAW=2
  CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS=2
  CONFIG_USB_GADGET_MUSB_HDRC=m
  CONFIG_USB_GADGET_DUALSPEED=y
  CONFIG_USB_GADGETFS=m
  # CONFIG_USB_MIDI_GADGET is not set

Fixes the following oops on module unloading:

  Unable to handle kernel NULL pointer dereference at virtual address 00000220
  ----8<----
  [<bf162088>] (omap2430_runtime_resume+0x24/0x54 [omap2430]) from [<c0302e34>] (pm_generic_runtime_resume+0x3c/0x50)
  [<c0302e34>] (pm_generic_runtime_resume+0x3c/0x50) from [<c0031a24>] (_od_runtime_resume+0x28/0x2c)
  [<c0031a24>] (_od_runtime_resume+0x28/0x2c) from [<c0306cb0>] (__rpm_callback+0x60/0xa0)
  [<c0306cb0>] (__rpm_callback+0x60/0xa0) from [<c0307f2c>] (rpm_resume+0x3fc/0x6e4)
  [<c0307f2c>] (rpm_resume+0x3fc/0x6e4) from [<c030851c>] (__pm_runtime_resume+0x5c/0x90)
  [<c030851c>] (__pm_runtime_resume+0x5c/0x90) from [<c02fd0dc>] (__device_release_driver+0x2c/0xd0)
  [<c02fd0dc>] (__device_release_driver+0x2c/0xd0) from [<c02fda18>] (driver_detach+0xe8/0xf4)
  [<c02fda18>] (driver_detach+0xe8/0xf4) from [<c02fcf88>] (bus_remove_driver+0xa0/0x104)
  [<c02fcf88>] (bus_remove_driver+0xa0/0x104) from [<c02fde54>] (driver_unregister+0x60/0x80)
  [<c02fde54>] (driver_unregister+0x60/0x80) from [<c02ff2d4>] (platform_driver_unregister+0x1c/0x20)
  [<c02ff2d4>] (platform_driver_unregister+0x1c/0x20) from [<bf162928>] (omap2430_exit+0x14/0x1c [omap2430])
  [<bf162928>] (omap2430_exit+0x14/0x1c [omap2430]) from [<c007d8bc>] (sys_delete_module+0x1f4/0x264)
  [<c007d8bc>] (sys_delete_module+0x1f4/0x264) from [<c000f000>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: NVladimir Zapolskiy <vladimir.zapolskiy@nokia.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org # 3.1
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This changes the otg functions so that they receive struct
otg instead of struct usb_phy as parameter and
converts all users of these functions to pass the otg member
of their usb_phy.

Includes fixes to IMX code from Sascha Hauer.

[ balbi@ti.com : fixed a compile warning on ehci-mv.c ]
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Acked-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: NLi Yang <leoli@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the new usb_phy_* functions with transceiver
operations instead of the old otg functions.

Includes fixes from Sascha Hauer.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: NLi Yang <leoli@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use struct usb_otg members with OTG specific functions instead
of usb_phy members.

[ balbi@ti.com: added a missing change on musb_gadget.c to avoid
	a compile error on a later patch ]
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There's really no point in doing all that
initcall trickery when we can safely let
udev handle module probing for us.

Remove all of that trickery, by moving everybody
to module_init() and making proper use of
platform_device_register() rather than
platform_device_probe().
Tested-by: NRajashekhara, Sudhakar <sudhakar.raj@ti.com>
Tested-by: NTasslehoff Kjappfot <tasskjapp@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

1/ remove incorrect comment (it is a non-blocking notifier)
2/ Use correct symbolic return value for notifier
3/ Make sure otg_notifier_work is cancelled before module exit.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

These are handled by drivers core, and in a way that doesn't wake up the
devices.
Signed-off-by: NFelipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

And use dev instead of musb->controller.
Signed-off-by: NFelipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

enabled && driver || !enabled can be simplified to !enabled || driver.
Signed-off-by: NFelipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

fix the following compile warning:

drivers/usb/musb/omap2430.c: In function 'musb_otg_notifier_work':
drivers/usb/musb/omap2430.c:279:3: warning: 'return' with a value, in
	function returning void
drivers/usb/musb/omap2430.c:282:2: warning: 'return' with a value, in
	function returning void
Signed-off-by: NFelipe Balbi <balbi@ti.com>

musb pm_runtime_get_sync call happens in intrrupt context on cable attach case
That can result in re-enabling the interrupts and cause side affects.

So move the code to a work queue.

Following is the error path hit on cable attach:

BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:802
in_atomic(): 0, irqs_disabled(): 0, pid: 18, name: irq/378-twl6030

Backtrace:
[<c00520f0>] (dump_backtrace+0x0/0x110) from [<c054f454>] (dump_stack+0x18/0x1c)
[<c054f43c>] (dump_stack+0x0/0x1c) from [<c007f59c>] (__might_sleep+0x130/0x134)
[<c007f46c>] (__might_sleep+0x0/0x134) from [<c02c2794>] (__pm_runtime_resume+0x94/0x98)
[<c02c2700>] (__pm_runtime_resume+0x0/0x98) from [<c033e7e4>] (musb_otg_notifications+0x9c/0x164)
[<c033e748>] (musb_otg_notifications+0x0/0x164) from [<c00b3df0>] (notifier_call_chain+0x4c/0x8c)
[<c00b3da4>] (notifier_call_chain+0x0/0x8c) from [<c00b44a8>] (__atomic_notifier_call_chain+0x40/0x54)
[<c00b4468>] (__atomic_notifier_call_chain+0x0/0x54) from [<c00b44dc>] (atomic_notifier_call_chain+0x20/0x28)
[<c00b44bc>] (atomic_notifier_call_chain+0x0/0x28) from [<c033f124>] (twl6030_usb_irq+0xc8/0xdc)
[<c033f05c>] (twl6030_usb_irq+0x0/0xdc) from [<c00d79f8>] (irq_thread_fn+0x24/0x40)
[<c00d79d4>] (irq_thread_fn+0x0/0x40) from [<c00d7b64>] (irq_thread+0x150/0x1d8)
[<c00d7a14>] (irq_thread+0x0/0x1d8) from [<c00adf70>] (kthread+0x94/0x98)
[<c00adedc>] (kthread+0x0/0x98) from [<c0094388>] (do_exit+0x0/0x720)

Tested with:
MUSB Device mode: Cold boot / Hot plug
MUSB Host mode: Cold boot / Hot plug
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove a few unnecessary headers from a
few files.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

we need to save and restore OTG_INTERFSEL register
else we will be unable to function on resume after
OFF mode.
Reported-by: NDevaraj Rangasamy <dev@ti.com>
Signed-off-by: NHema HK <hemahk@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

the MUSB IP is always OTG, so there's no point
in adding so many ifdefs on the code. Drop those
and always compile the driver for OTG support.

This also allows us to drop the useless "driver
mode" choice. For doing that, we need to make
musb depend on both Host and Peripheral side.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We have a generic way of enabling/disabling
different debug messages on a driver called
DYNAMIC_PRINTK. Anyone interested in enabling
just part of the debug messages, please read
the documentation under:

Documentation/dynamic-debug-howto.txt

for information on how to use that great
infrastructure.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Commit 3dacdf11 "usb: factor out state_string() on otg drivers"
broke building musb drivers since there is already another
otg_state_string() function in musb drivers, but with different
prototype. Fix musb drivers to use common otg_state_string(), too.

Also provide a nop for otg_state_string() if CONFIG_USB_OTG_UTILS
is not defined.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Recent runtime pm and hwmod conversions for 2.6.39 broke the musb peripheral
mode OMAP retention idle on boards where the board mode in struct
musb_hdrc_platform_data is set to MUSB_PERIPHERAL.

These conversions changed the way how the OTG_SYSCONFIG register is
configured and used in runtime. Before 2.6.39 smart standby/idle modes were
activated statically in OTG_SYSCONFIG. Those modes allow that the musb is
able to idle when peripheral device is not connected to host.

In 2.6.39 the OTG_SYSCONFIG is updated runtime depending on VBUS status.
No standby/idle modes are used when device is connected and force
standby/idle when disconnected.

Unfortunately VBUS disconnect event that handles the disconnect case lets
the peripheral musb to idle only when board mode is MUSB_OTG. Fix this by
checking the peripheral mode also.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix build failure introduced by commit
7acc6197 (usb: musb: Idle path retention
and offmode support for OMAP3) when building without gadget
support.

  CC      drivers/usb/musb/omap2430.o
drivers/usb/musb/omap2430.c: In function ‘musb_otg_notifications’:
drivers/usb/musb/omap2430.c:262: error: ‘struct musb’ has no member named ‘gadget_driver’
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In OMAP3xxx with OTG mode or host only mode, When the device
is inserted after the gadget driver loading the enumeration was not
through. This is because the mentor controller will start sensing the
ID PIN only after setting the session bit.
So after ID-GND, need to set the session bit for mentor to get it
configured as A device.

This is a fix to set the session bit again in ID_GND notification handler.
Tested with OMAP3630Zoom3 platform.
Signed-off-by: NHema HK <hemahk@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch supports the retention and offmode support in the idle path for
musb driver using runtime pm APIs.

This is restricted to support offmode and retention only when device not
connected.When device/cable connected with gadget driver loaded,configured
to no idle/standby which will not allow the core transition to retention
or off.

There is no context save/restore done by hardware for musb in OMAP3
and OMAP4,driver has to take care of saving and restoring the context
during offmode.

Musb has a requirement of configuring sysconfig register to force
idle/standby mode and set the ENFORCE bit in module STANDBY register
for retention and offmode support.

Runtime pm and hwmod frameworks will take care of configuring to force
idle/standby when pm_runtime_put_sync is called and back to no
idle/standby when pm_runeime_get_sync is called.

Compile, boot tested and also tested the retention in the idle path on
OMAP3630Zoom3. And tested the global suspend/resume with offmode enabled.
Usb basic functionality tested on OMAP4430SDP.

There is some problem with idle path offmode in mainline, I could not test
with offmode. But I have tested this patch with resetting the controller
in the idle path when wakeup from retention just to make sure that the
context is lost, and restore path is working fine.

Removed .suspend/.resume fnction pointers and functions because there
is no need of having these functions as all required work is done
at runtime in the driver.

There is no need to call the runtime pm api with glue driver device
as glue layer device is the parent of musb core device, when runtime apis
are called for the child, parent device runtime functionality
will be invoked.

Design overview:

pm_runtime_get_sync: When called with musb core device takes care of
enabling the clock, calling runtime callback function of omap2430 glue
layer, runtime call back of musb driver and configure the musb sysconfig
to no idle/standby

pm_runtime_put: Takes care of calling runtime callback function of omap2430
glue layer, runtime call back of musb driver, Configure the musb sysconfig
to force idle/standby and disable the clock.

During musb driver load: Call pm_runtime_get_sync.

End of musb driver load: Call pm_runtime_put

During gadget driver load: Call pm_runtime_get_sync,
End of gadget driver load: Call pm_runtime_put if there is no device
or cable is connected.

During unload of the gadget driver:Call pm_runtime_get_sync if cable/device
is not connected.
End of the gadget driver unload : pm_runtime_put

During unload of musb driver : Call pm_runtime_get_sync
End of unload: Call pm_runtime_put

On connect of usb cable/device -> transceiver notification(VBUS and ID-GND):
pm_runtime_get_sync only if the gadget driver loaded.

On disconnect of the cable/device -> Disconnect Notification:
pm_runtime_put if the gadget driver is loaded.
Signed-off-by: NHema HK <hemahk@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

For OMAP3 and OMAP4 for offmode and retention support, musb
sysconfig is configured to force idle and standby with ENABLE_FORCE bit
of OTG_FORCESTNDBY set.
And on wakeup configure to no ilde/standby with resetting the ENABLE_FORCE
bit. There is not need to save and restore of this register anymore
so removed omap2430_save_context/omap2430_restore_context functions.
and also removed otg_forcestandby member of musb_context_registers
structure
Signed-off-by: NHema HK <hemahk@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

OMAP4430 is embedded with UTMI PHY. This PHY does not support the
OTG features like ID pin detection and VBUS detection. This function
is exported to an external companion chip TWL6030. Software must retrieve
the OTG HNP and SRP status from the TWL6030 and configure the bits inside
the control module that drive the related USBOTGHS UTMI interface signals.
It must also read back the UTMI signals needed to configure the TWL6030
OTG module.

Can find more details in the TRM[1].
[1]:http://focus.ti.com/pdfs/wtbu/OMAP4430_ES2.0_Public_TRM_vJ.pdf

In OMAP4430 musb driver VBUS and ID notifications are received from the
transceiver driver. If the cable/device is connected during boot,
notifications from transceiver driver will be missed till musb driver
is loaded.
Patch to configure the transceiver in the platform_enable/disable
functions and enable the vbus in the gadget driver based on the
last_event of the otg_transceiver.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Calling runtime pm APIs pm_runtime_put_sync() and pm_runtime_get_sync()
for enabling/disabling the clocks, sysconfig settings.

Enable clock, configure no-idle/standby when active and configure force idle/standby
and disable clock when idled. This is taken care by the runtime framework when
driver calls the pm_runtime_get_sync and pm_runtime_put_sync APIs.
Need to configure MUSB into force standby and force idle mode when usb not used
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Cancel idle timer in musb_platform_exit.

The idle timer could trigger after clock had been disabled leading to
kernel panic when MUSB_DEVCTL is accessed in musb_do_idle on 2.6.37.

The fault below is no longer triggered on 2.6.38-rc4 (clock is disabled
later, and only if compiled as a module, and the offending memory access
has moved) but the timer should be cancelled nonetheless.

Rebooting... musb_hdrc musb_hdrc: remove, state 4
usb usb1: USB disconnect, address 1
musb_hdrc musb_hdrc: USB bus 1 deregistered
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab060
Internal error: : 1028 [#1] PREEMPT
last sysfs file: /sys/kernel/uevent_seqnum
Modules linked in:
CPU: 0    Not tainted  (2.6.37+ #6)
PC is at musb_do_idle+0x24/0x138
LR is at musb_do_idle+0x18/0x138
pc : [<c02377d8>]    lr : [<c02377cc>]    psr: 80000193
sp : cf2bdd80  ip : cf2bdd80  fp : c048a20c
r10: c048a60c  r9 : c048a40c  r8 : cf85e110
r7 : cf2bc000  r6 : 40000113  r5 : c0489800  r4 : cf85e110
r3 : 00000004  r2 : 00000006  r1 : fa0ab000  r0 : cf8a7000
Flags: Nzcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c5387d  Table: 8faac019  DAC: 00000015
Process reboot (pid: 769, stack limit = 0xcf2bc2f0)
Stack: (0xcf2bdd80 to 0xcf2be000)
dd80: 00000103 c0489800 c02377b4 c005fa34 00000555 c0071a8c c04a3858 cf2bdda8
dda0: 00000555 c048a00c cf2bdda8 cf2bdda8 1838beb0 00000103 00000004 cf2bc000
ddc0: 00000001 00000001 c04896c8 0000000a 00000000 c005ac14 00000001 c003f32c
dde0: 00000000 00000025 00000000 cf2bc000 00000002 00000001 cf2bc000 00000000
de00: 00000001 c005ad08 cf2bc000 c002e07c c03ec039 ffffffff fa200000 c0033608
de20: 00000001 00000000 cf852c14 cf81f200 c045b714 c045b708 cf2bc000 c04a37e8
de40: c0033c04 cf2bc000 00000000 00000001 cf2bde68 cf2bde68 c01c3abc c004f7d8
de60: 60000013 ffffffff c0033c04 00000000 01234567 fee1dead 00000000 c006627c
de80: 00000001 c00662c8 28121969 c00663ec cfa38c40 cf9f6a00 cf2bded0 cf9f6a0c
dea0: 00000000 cf92f000 00008914 c02cd284 c04a55c8 c028b398 c00715c0 becf24a8
dec0: 30687465 00000000 00000000 00000000 00000002 1301a8c0 00000000 00000000
dee0: 00000002 1301a8c0 00000000 00000000 c0450494 cf527920 00011f10 cf2bdf08
df00: 00011f10 cf2bdf10 00011f10 cf2bdf18 c00f0b44 c004f7e8 cf2bdf18 cf2bdf18
df20: 00011f10 cf2bdf30 00011f10 cf2bdf38 cf401300 cf486100 00000008 c00d2b28
df40: 00011f10 cf401300 00200200 c00d3388 00011f10 cfb63a88 cfb63a80 c00c2f08
df60: 00000000 00000000 cfb63a80 00000000 cf0a3480 00000006 c0033c04 cfb63a80
df80: 00000000 c00c0104 00000003 cf0a3480 cfb63a80 00000000 00000001 00000004
dfa0: 00000058 c0033a80 00000000 00000001 fee1dead 28121969 01234567 00000000
dfc0: 00000000 00000001 00000004 00000058 00000001 00000001 00000000 00000001
dfe0: 4024d200 becf2cb0 00009210 4024d218 60000010 fee1dead 00000000 00000000
[<c02377d8>] (musb_do_idle+0x24/0x138) from [<c005fa34>] (run_timer_softirq+0x1a8/0x26)
[<c005fa34>] (run_timer_softirq+0x1a8/0x26c) from [<c005ac14>] (__do_softirq+0x88/0x13)
[<c005ac14>] (__do_softirq+0x88/0x138) from [<c005ad08>] (irq_exit+0x44/0x98)
[<c005ad08>] (irq_exit+0x44/0x98) from [<c002e07c>] (asm_do_IRQ+0x7c/0xa0)
[<c002e07c>] (asm_do_IRQ+0x7c/0xa0) from [<c0033608>] (__irq_svc+0x48/0xa8)
Exception stack(0xcf2bde20 to 0xcf2bde68)
de20: 00000001 00000000 cf852c14 cf81f200 c045b714 c045b708 cf2bc000 c04a37e8
de40: c0033c04 cf2bc000 00000000 00000001 cf2bde68 cf2bde68 c01c3abc c004f7d8
de60: 60000013 ffffffff
[<c0033608>] (__irq_svc+0x48/0xa8) from [<c004f7d8>] (sub_preempt_count+0x0/0xb8)
Code: ebf86030 e5940098 e594108c e5902010 (e5d13060)
---[ end trace 3689c0d808f9bf7c ]---
Kernel panic - not syncing: Fatal exception in interrupt

Cc: stable <stable@kernel.org>
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Cancel idle timer in musb_platform_exit.

The idle timer could trigger after clock had been disabled leading to
kernel panic when MUSB_DEVCTL is accessed in musb_do_idle on 2.6.37.

The fault below is no longer triggered on 2.6.38-rc4 (clock is disabled
later, and only if compiled as a module, and the offending memory access
has moved) but the timer should be cancelled nonetheless.

Rebooting... musb_hdrc musb_hdrc: remove, state 4
usb usb1: USB disconnect, address 1
musb_hdrc musb_hdrc: USB bus 1 deregistered
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab060
Internal error: : 1028 [#1] PREEMPT
last sysfs file: /sys/kernel/uevent_seqnum
Modules linked in:
CPU: 0    Not tainted  (2.6.37+ #6)
PC is at musb_do_idle+0x24/0x138
LR is at musb_do_idle+0x18/0x138
pc : [<c02377d8>]    lr : [<c02377cc>]    psr: 80000193
sp : cf2bdd80  ip : cf2bdd80  fp : c048a20c
r10: c048a60c  r9 : c048a40c  r8 : cf85e110
r7 : cf2bc000  r6 : 40000113  r5 : c0489800  r4 : cf85e110
r3 : 00000004  r2 : 00000006  r1 : fa0ab000  r0 : cf8a7000
Flags: Nzcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c5387d  Table: 8faac019  DAC: 00000015
Process reboot (pid: 769, stack limit = 0xcf2bc2f0)
Stack: (0xcf2bdd80 to 0xcf2be000)
dd80: 00000103 c0489800 c02377b4 c005fa34 00000555 c0071a8c c04a3858 cf2bdda8
dda0: 00000555 c048a00c cf2bdda8 cf2bdda8 1838beb0 00000103 00000004 cf2bc000
ddc0: 00000001 00000001 c04896c8 0000000a 00000000 c005ac14 00000001 c003f32c
dde0: 00000000 00000025 00000000 cf2bc000 00000002 00000001 cf2bc000 00000000
de00: 00000001 c005ad08 cf2bc000 c002e07c c03ec039 ffffffff fa200000 c0033608
de20: 00000001 00000000 cf852c14 cf81f200 c045b714 c045b708 cf2bc000 c04a37e8
de40: c0033c04 cf2bc000 00000000 00000001 cf2bde68 cf2bde68 c01c3abc c004f7d8
de60: 60000013 ffffffff c0033c04 00000000 01234567 fee1dead 00000000 c006627c
de80: 00000001 c00662c8 28121969 c00663ec cfa38c40 cf9f6a00 cf2bded0 cf9f6a0c
dea0: 00000000 cf92f000 00008914 c02cd284 c04a55c8 c028b398 c00715c0 becf24a8
dec0: 30687465 00000000 00000000 00000000 00000002 1301a8c0 00000000 00000000
dee0: 00000002 1301a8c0 00000000 00000000 c0450494 cf527920 00011f10 cf2bdf08
df00: 00011f10 cf2bdf10 00011f10 cf2bdf18 c00f0b44 c004f7e8 cf2bdf18 cf2bdf18
df20: 00011f10 cf2bdf30 00011f10 cf2bdf38 cf401300 cf486100 00000008 c00d2b28
df40: 00011f10 cf401300 00200200 c00d3388 00011f10 cfb63a88 cfb63a80 c00c2f08
df60: 00000000 00000000 cfb63a80 00000000 cf0a3480 00000006 c0033c04 cfb63a80
df80: 00000000 c00c0104 00000003 cf0a3480 cfb63a80 00000000 00000001 00000004
dfa0: 00000058 c0033a80 00000000 00000001 fee1dead 28121969 01234567 00000000
dfc0: 00000000 00000001 00000004 00000058 00000001 00000001 00000000 00000001
dfe0: 4024d200 becf2cb0 00009210 4024d218 60000010 fee1dead 00000000 00000000
[<c02377d8>] (musb_do_idle+0x24/0x138) from [<c005fa34>] (run_timer_softirq+0x1a8/0x26)
[<c005fa34>] (run_timer_softirq+0x1a8/0x26c) from [<c005ac14>] (__do_softirq+0x88/0x13)
[<c005ac14>] (__do_softirq+0x88/0x138) from [<c005ad08>] (irq_exit+0x44/0x98)
[<c005ad08>] (irq_exit+0x44/0x98) from [<c002e07c>] (asm_do_IRQ+0x7c/0xa0)
[<c002e07c>] (asm_do_IRQ+0x7c/0xa0) from [<c0033608>] (__irq_svc+0x48/0xa8)
Exception stack(0xcf2bde20 to 0xcf2bde68)
de20: 00000001 00000000 cf852c14 cf81f200 c045b714 c045b708 cf2bc000 c04a37e8
de40: c0033c04 cf2bc000 00000000 00000001 cf2bde68 cf2bde68 c01c3abc c004f7d8
de60: 60000013 ffffffff
[<c0033608>] (__irq_svc+0x48/0xa8) from [<c004f7d8>] (sub_preempt_count+0x0/0xb8)
Code: ebf86030 e5940098 e594108c e5902010 (e5d13060)
---[ end trace 3689c0d808f9bf7c ]---
Kernel panic - not syncing: Fatal exception in interrupt

Cc: stable@kernel.org
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

OMAP4430 supports UTMI and ULPI types of transceiver interface.

In UTMI mode: The PHY is embedded within OMAP4430. The transceiver functionality
is split between the twl6030 PMIC chip and OMAP4430. The VBUS, ID pin
sensing and OTG SRP generation part is integrated in TWL6030 and UTMI PHY
functionality is embedded within the OMAP4430.

There is no direct interactions between the MUSB controller and TWL6030
chip to communicate the session-valid, session-end and ID-GND events.
It has to be done through a software by setting/resetting bits in
one of the control module register of OMAP4430 which in turn toggles
the appropriate signals to MUSB controller.

musb driver is register for blocking notifications from the transceiver
driver to get the event notifications for connect/disconnect and ID-GND.
Based on these events call the transceiver init/shutdown function to
configure the transceiver to toggle the VBUS valid, session end and ID_GND
signals to musb and power on/off the internal PHY.

For ID_GND event notifications, toggle the ID_GND signal and then wait for
musb to be configured as "A" device, and then call the transceiver function
to set the VBUS.

In OTG mode and musb as a host, When the Micro A connector used, VBUS is turned on
and session bit set. When the device is connected, enumeration goes through.
When the device disconnected from the other end of the connector(ID is still grounded),
link will detect the disconnect and end the session. When the device is connected back,
there are no events generated in the TWL6030-usb, and link is already down.
So the device is not detected. Removed the session bit disable code which
will recognize the connect of the device.

Limitation: In OTG host mode, if device is connected during boot, it does not get
detected. If disconnect and connect it back or connect after boot only it works.
Fix for this, I will submit seperate patch later.
Signed-off-by: NHema HK <hemahk@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

that's not used anymore. So let's drop it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

instead of using musb_platform_suspend/resume,
we can use dev_pm_ops and let the platform_device
core handle when to call musb_core's suspend and
glue layer's suspend.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

we don't need those nops, so drop them.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

... that can be easily folded into the
musb_platform_suspend/resume calls.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

musb core doesn't need to know about platform
specific details. So start moving clock
handling to platform glue layer and make
musb core agnostic about that.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

... then we don't need to export any symbols
from glue layer to musb_core.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

that structure currently only holds a device
pointer to our own platform_device and musb's
platform_device, but soon it will hold pointers
to our clock structures and glue-specific bits
and pieces.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Just adding its own platform_driver, not really
using it yet.

When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

preparing to a big refactor on musb code. We need
to be able to compile in all glue layers (or at
least all ARM-based ones) together and have a
working binary.

While preparing for that, we move every glue
layer to export only one symbol, which is
a struct musb_platform_ops, and make all
other functions static.

Later patches will come to allow for compiling
all glue layers together and have a working
binary.
Signed-off-by: NFelipe Balbi <balbi@ti.com>